A range of dc rated multi-layer chip capacitors from
0.47pF to 22µF and in case sizes 0603 to 8060 in
C0G/NP0 and X7R dielectrics. Suitable for all general
purpose and high reliability applications where package
size and reliability are important. All are manufactured
using Syfer’s unique wet process and incorporate
precious metal electrodes.
Dissipation Factor
Ageing Rate
Range Dimensions – Standard MLCC Ranges
Length
(L1)
mm/inches
1.6 ± 0.2
0.063 ± 0.008
2.0 ± 0.3
0.08 ± 0.012
3.2 ± 0.3
0.126 ± 0.012
3.2 ± 0.3
0.126 ± 0.012
4.5 ± 0.35
0.18 ± 0.014
4.5 ± 0.35
0.18 ± 0.014
4.5 ± 0.35
0.18 ± 0.014
5.7 ± 0.4
0.225 ± 0.016
5.7 ± 0.4
0.225 ± 0.016
9.2 ± 0.5
0.36 ± 0.02
14.0 ± 0.5
0.55 ± 0.02
20.3 ± 0.5
0.8 ± 0.02
Width
(W)
mm/inches
0.8 ± 0.2
0.031 ± 0.008
1.25 ± 0.2
0.05 ± 0.008
1.6 ± 0.2
0.063 ± 0.008
2.5 ± 0.3
0.1 ± 0.012
2.0 ± 0.3
0.08 ± 0.012
3.2 ± 0.3
0.126 ± 0.012
6.30 ± 0.4
0.25 ± 0.016
5.0 ± 0.4
0.197 ± 0.016
6.3 ± 0.4
0.25 ± 0.016
10.16 ± 0.5
0.4 ± 0.02
12.7 ± 0.5
0.5 ± 0.02
15.24 ± 0.5
0.6 ± 0.02
Max. Thickness
(T)
mm/inches
0.8
0.013
1.3
0.051
1.6
0.063
2.0
0.08
2.0
0.08
2.5
0.1
2.5
0.1
4.2
0.16
4.2
0.16
2.5
0.1
4.2
0.16
2.5
0.1
Termination Band
(L2)
mm/inches
min
0.10
0.004
0.13
0.005
0.25
0.01
0.25
0.01
0.25
0.01
0.25
0.01
0.25
0.01
0.25
0.01
0.25
0.01
0.5
0.02
0.5
0.02
0.5
0.02
max
0.40
0.015
0.75
0.03
0.75
0.03
0.75
0.03
1.0
0.04
1.0
0.04
1.0
0.04
1.0
0.04
1.0
0.04
1.5
0.06
1.5
0.06
1.5
0.06
Size
0603
0805
1206
1210
1808
1812
1825
2220
2225
3640
5550
8060
Custom chip sizes not included in the table, but larger than 2225, can be considered with minimum tooling charges. Please refer specific requests direct to the sales office.
Max thickness relates to standard components and actual thickness may be considerably less. Thicker parts, or components with reduced maximum thickness, can be considered by request – please refer
Features of LM3S8962 serial port module;
1. Support configurable data of 5~8 bits; maximum baud rate 3.125MHZ;2. The start bit and stop bit bandwidth are configurable;
3. The check mode can be configu...
Remove with a soldering iron:Step 1. Use an enameled wire with a diameter of about 0.15mm to pass under the first row of pins, fix one end and hold the other end in your hand.2. Heat the moving end of...
An I2C is simulated in STM32. When communicating with the ferroelectric, it is found that the ferroelectric has no response. Therefore, the function of reading the ferroelectric cannot be used! ! ! !
...
Medical and industrial applications often require isolation voltages of 2500Vac or higher for patient and equipment operator safety. The isolation barrier must not only transmit power to the sensin...[Details]
This summary will introduce the transmitter characteristic test of TD terminal products - uplink power control. According to the 3GPP TS34.122 standard, UE uplink power control is divided into uplink ...[Details]
Overview
Currently, many portable consumer electronic products, such as mobile phones, PDAs, MP3 players, and notebooks, are equipped with display screens. Although the type and size of the di...[Details]
Overview
In recent years, the vigorous development of integrated circuits has created a huge space for the research and application of digital circuits. FPGA has low power consumption, high re...[Details]
Introduction
The MAX2116 P1db data is measured at specific combinations of RF and baseband gain over the adjustable range of these two gains. These data can be used to select gain control se...[Details]
In the issue of ensuring the safety of drivers and pedestrians, the proportion of electronic technology has increased. According to the survey, 80% to 90% of traffic accidents are caused by driver...[Details]
Multiple Input and Multiple Output (MIMO) technology is arguably the next most important development in wireless communication technology since the advent of digital communications. Many new wir...[Details]
In the process of RF transceiver application, adjusting the processing gain (PG) of the direct sequence spread spectrum communication system (DSSS) can obtain excellent anti-noise performance, whic...[Details]
Portable products are generally powered by batteries. Due to cost and size considerations, there is a trend to reduce the number and size of batteries used in design. If the number of batteries is ...[Details]
1 Introduction
In many communication systems, the base station usually sends a training sequence for the terminal to synchronize with the system. The synchronization here includes time syn...[Details]
CVC5.0 (CSR recently announced the fifth generation of clear voice capture technology) is the only solution on the market that provides advanced audio enhancement and noise suppression to both the ...[Details]
1 Introduction
Digital video is the use of video capture devices such as cameras to collect external image information and digitize the image information, and then record it to storage med...[Details]
Plasma processing in the semiconductor industry is a challenging environment for fluororubber vacuum seals. The ability to seal under high temperature and plasma conditions is critical to maximizin...[Details]
Our company's teardown work has always been as close to global technology trends as possible, but not all new product trials are like this. Just as Japan frequently conducts new product trials in i...[Details]
Recently, Infineon Technologies AG launched the world's first monolithic linear regulator with integrated diagnostics and protection functions for in-vehicle radio systems, further expanding its pr...[Details]
Talking
京公网安备 11010802033920号
EEWORLD
