EEWORLDEEWORLDEEWORLD

Part Number

Search

SIT9005ACE2D-33ND

Description
OSC MEMS
CategoryPassive components   
File Size333KB,9 Pages
ManufacturerSiTime
Environmental Compliance
Download Datasheet Parametric View All

SIT9005ACE2D-33ND Overview

OSC MEMS

SIT9005ACE2D-33ND Parametric

Parameter NameAttribute value
typeSSXO MEMS
Programmable typeProgrammed by Digi-Key (please enter your desired frequency on the website order form)
Available frequency range1MHz ~ 141MHz
Function-
outputLVCMOS
Voltage - Power3.3V
frequency stability±20ppm,±25ppm,±50ppm
Frequency stability (overall)-
Operating temperature-20°C ~ 70°C
spread spectrum bandwidth-1.04%, Down Spread
Current - Power (maximum)6.5mA
grade-
Installation typesurface mount
Package/casing4-SMD, no leads
size/dimensions0.126" long x 0.098" wide (3.20mm x 2.50mm)
high0.030"(0.76mm)
SiT9005
1 to 141 MHz EMI Reduction Oscillator
Features
Applications
Spread spectrum for EMI reduction
Wide spread % option
Center spread: from ±0.125% to ±2%, ±0.125% step size
Down spread: -0.25% to -4% with -0.25% step size
Spread profile option: Triangular, Hershey-kiss
Programmable rise/fall time for EMI reduction: 8 options,
0.25 to 40 ns
Any frequency between 1 MHz and 141 MHz accurate to
6 decimal places
100% pin-to-pin drop-in replacement to quartz-based XO’s
Excellent total frequency stability as low as ±20 ppm
Operating temperature from -40°C to 85°C.
Low power consumption of 4.0 mA typical at 1.8V
Pin1 modes: Standby, output enable, or spread disable
Fast startup time of 5 ms
LVCMOS output
Industry-standard packages
QFN: 2.0 x 1.6, 2.5 x 2.0, 3.2 x 2.5 mm
2
Contact
SiTime
for SOT23-5 (2.9 x 2.8 mm
2
)
RoHS and REACH compliant, Pb-free, Halogen-free
and Antimony-free
Surveillance camera
IP camera
Industrial motors
Flat panels
Multi function printers
PCI express
Electrical Specifications
Table 1. Electrical Characteristics
All Min and Max limits are specified over temperature and rated operating voltage with 15 pF output load unless otherwise stated.
Typical values are at 25°C and 3.3V supply voltage.
Parameters
Output Frequency Range
Symbol
Min.
Typ.
Max.
Unit
Condition
Frequency Range
f
1
141
MHz
Frequency Stability and Aging
Frequency Stability
F_stab
-20
-25
-50
Operating Temperature Range
T_use
-20
-40
Supply Voltage
Vdd
1.62
2.25
2.52
2.7
2.97
2.25
Current Consumption
OE Disable Current
Idd
I_OD
Standby Current
I_std
1.8
2.5
2.8
3.0
3.3
5.6
5.0
5.0
4.6
2.1
0.4
+20
+25
+50
+70
+85
1.98
2.75
3.08
3.3
3.63
3.63
6.5
5.5
6.5
5.2
4.3
1.5
ppm
ppm
ppm
°C
°C
V
V
V
V
V
V
mA
mA
mA
mA
µA
µA
No load condition, f = 40 MHz, Vdd = 2.5V to 3.3V
No load condition, f = 40 MHz, Vdd = 1.8V
f = 40 MHz, Vdd = 2.5V to 3.3V, OE = GND, Output in high-Z
state
f = 40 MHz, Vdd = 1.8V, OE = GND, Output in high-Z state
ST
= GND, Vdd = 2.5V to 3.3V, Output is weakly pulled down
ST
= GND, Vdd = 1.8V, Output is weakly pulled down
Inclusive of initial tolerance at 25°C, 1st year aging at 25°C, and
variations over operating temperature, rated power supply
voltage. Spread = Off.
Operating Temperature Range
Extended Commercial
Industrial
Supply Voltage and Current Consumption
Rev 1.0
September 25, 2017
www.sitime.com
The FGPAs of the Cyclone IV series are set as output deriving ground. The FPGA pins are all high level.
The fgpa pins of the cyclone iv series are set as output deriving ground. When testing the fpga pins, they are all high level, and the measured io port voltages are all 3.3v. Is the default output lev...
tianma123 FPGA/CPLD
What chips are supported in Keil?
What chips are supported in Keil? What software is used to program arm7?...
blue670117 Embedded System
The problem of different voltages at the two input terminals of the operational amplifier
I need some advice. I am using an operational amplifier. The input voltage at the positive input is 1V, but the voltage at the negative input is 0V. According to the virtual short principle of the ope...
王小明A Analog electronics
First time
When I first arrived, I broadened my horizons and found myself so weak....
经世致用 Talking
Waiting for epoll events
The system call epoll_wait() waits for events on the file descriptor associated with the specified epoll instance: #include int epoll_wait(int epfd, struct epoll_event *events, int maxevents, int time...
chenbingjy Linux and Android
Please recommend an embedded real-time OS with a small kernel suitable for learning
I want to find an OS that has many applications, is easy to port, has a small amount of code, and is suitable for learning. I heard that freeRTOS and RT-Thread are good, but I haven't used them.Please...
ozx0512 stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 634  36  298  1955  546  13  1  6  40  11 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号