Y4725187R200T9L datasheet, PDF

Datasheet> All Categories > Passive components> Y4725187R200T9L

Y4725187R200T9L: DescriptionRES 187.2 OHM 3/4W 0.01% AXIAL; CategoryPassive components; File Size466KB，6 Pages; ManufacturerVishay; Websitehttp://www.vishay.com; Environmental Compliance

Download Datasheet Parametric View All

Y4725187R200T9L Overview

RES 187.2 OHM 3/4W 0.01% AXIAL

Y4725187R200T9L Parametric

Parameter Name	Attribute value
resistance	187.2 Ohms
Tolerance	±0.01%
Power (W)	0.75W，3/4W
component	metal foil
characteristic	non-inductive
Temperature Coefficient	±0.2ppm/°C
Operating temperature	-55°C ~ 125°C
Package/casing	Radial - 4 leads
Supplier device packaging	-
size/dimensions	0.500" diameter x 0.625" length (12.70mm x 15.88mm)
Height - Installation (maximum)	-
Number of terminals	4
failure rate	-

Preview

Download Datasheet

View All

HZ Series (Z-Foil) with Zero TCR

Vishay Foil Resistors

New Generation of Secondary Standards Hermetically Sealed Construction Ultra High

Precision Z-Foil Technology Resistors with TCR of ± 0.2 ppm/°C, Tolerance of ± 0.001 %

and Load Life Stability of ± 0.002 % (Metrology, Laboratory, Instrumentation, Industrial)

FEATURES



Temperature coefficient of resistance (TCR):

± 0.2 ppm/°C typical (- 55 °C to + 125 °C,

+ 25 °C ref.). For ultra high performances

(instrumentation and metrology) please refer to

the last page



Resistance range: 5



to 1.1 M (higher or lower values of

resistance available)



Foil resistors are not restricted to standard values; specific

“as required” values can be supplied at no extra cost or

delivery (e.g. 1K2345 vs. 1K)



Power coefficient “R due to self heating”:

5 ppm at rated power with the Z-Foil technology



Tolerance:

to ± 0.001 % (10 ppm)



Load life stability to ± 0.002 % (20 ppm) at 25 °C, 2000 h

at rated power



Load life stability, can be considerably improved

through in-house stabilization



Shelf life stability: 2 ppm for at least 6 years

(unaffected by humidity)



Electrostatic discharge (ESD) up to 25 000 V



Power rating: 0.3 W to 2.5 W at + 25 °C (depending on

model - see table 2)



Non-inductive, non-capacitive design



Non hot spot design



Rise time: 1 ns effectively no ringing



Current noise: 0.010 µV

RMS

/V of applied voltage (< - 40 dB)



Thermal EMF: 0.05 µV/°C typical



Voltage coefficient: < 0.1 ppm/V



Thermal stabilization time < 1 s (nominal value achieved

within 10 ppm of steady state value)



Non-inductive: < 0.08 µH



Terminal finish available: lead (Pb)-free or tin/lead alloy



Impervious to harmful environments - oil filled



Prototype quantities available in just 5 working days

or sooner. For more information, please contact

foil@vishaypg.com



For better performances (values, TCR, tolerance, stability),

please contact us

INTRODUCTION

The Z-Foil based oil filled, hermetically sealed HZ Series

resistors represent an industry breakthrough. The hermetic

sealing eliminates the ingress of moisture and oxygen, while

the oil acts as a thermal conductor, thus eliminating

long-term degradation elements of unsealed resistors, while

at the same time allowing the device to accept short periods

of overload without degradation.

The Z-Foil technology provides a significant reduction of the

resistive components, sensitivity to ambient temperature

variations (TCR) and applied power changes (PCR). When

combined with the hermetic sealing and oil filling, the

HZ Series resistors become

the most precise and stable

resistors available.

They are used as the most precise

secondary standards for ultra precision metrology.

With accuracies of ± 0.001 % (10 ppm) and a resistance

range from 5



to 1.1 M and long term shelf life of less than

2 ppm, these devices are virtually secondary standards that

can be carried in sets for daily or periodic calibration of

factory measurement equipment.

The HZ Series is available with laboratory and metrology

level precision and long-term stability with additional

in-house oriented processes such as: chip stabilization,

special TCR plotting, additional treatments for ultra

stability and special post manufacturing operations

(PMO). (Please refer to the last page)

TABLE 1 - TCR VS. RESISTANCE VALUE

RESISTANCE VALUE

()

TYPICAL TCR AND

MAX. SPREAD

(- 55 °C to + 125 °C, + 25 °C ref.)

(ppm/°C)

± 0.2 ± 2

± 0.2 ± 3

± 0.2 ± 4

FIGURE 1 - SHELF LIFE - VHA518-11

12K9 VS. QHE

0.9

0.8

0.7

0.6

0.5

0.4

0.3

0.2

0.1

- 0.1

100 200 300 400 500 600 700 800 900 1000

100 to < 1M1

50 to < 100

5 to < 50

Note

• For maximum TCR < 1 ppm/°C, see VHP100 and contact

application engineering

Resistance Change (ppm)

Time (Days)

Document Number: 63120

Revision: 25-Mar-10

For any questions, contact:

foil@vishaypg.com

www.foilresistors.com

Recommended Resources

Dual power supply specifications require you to understand

Thermocouple Isolation Amplifier

555 integrated direct reading audio meter circuit

MAXl898 single-cell Li+ battery linear charger

WIFI car can be controlled by mobile phone: A complete set of materials for making the WIFI car, including the Android program source code module for the mobile phone, the ST-MW-08S module is available on Taobao....; CFE2011 DIY/Open Source Hardware

A car that can rotate on the spot: Without solid driving skills, it is difficult to make a car rotate 360 degrees on the spot. However, with the concept car we introduce to you today, this "stunt" has become commonplace.The connection ...; xyh_521 Creative Market

How do I download the application developed under EVC to the target platform?: After I compiled the winCE kernel with PB, I downloaded the image to the target platform and started running it. Now the next step is to develop the application, which is to download the application u...; cswer911 Embedded System

That expert has used DP-1581+ MCU to develop things, and is currently learning...: That expert has used DP-1581 + MCU to develop things, and now I am learning... Can you give me some code reference to learn, even the simplest one is fine, it's just for learning. Now I have a simulat...; yzmb1985 Embedded System

The GCC version of HELPER2416+RAWOS is basically available: The code repository is as follows: [url=https://git.oschina.net/raw-os/gcc_helper2416.git]https://git.oschina.net/raw-os/gcc_helper2416.git[/url] Brothers who are interested can download it for trial,...; spacexplorer Embedded System

Testing and debugging of DSP system 4: Testing and debugging of DSP system 4...; 安_然 Microcontroller MCU

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components