MODEL 5610 SERIES
2” Diameter
Single Turn
Wirewound
Precision Potentiometer
MODEL STYLES
2
5611
5613
ELECTRICAL
1/4" Shaft, 3/8" Bushing
1/4" Shaft, Servo
Resistance Range, Ohms
Standard Resistance Tolerance
Minimum Practical Resistance Tolerance
Independent Linearity
Minimum Practical Independent Linearity
Power Rating, Watts
Dielectric Strength
Insulation Resistance, Minimum
Noise, Maximum
Actual Electrical Travel
Tap Tolerance
End Voltage, Maximum
ENVIRONMENTAL (MIL-R-12934)
15 to 80K
±5%
±1.0%
±1.0%, <50 Ohms
±0.5%,
≥50
Ohms
±1.0%, <50 Ohms
±0.5%, 50-499 Ohms
±0.25%, 500-4,999 Ohms
±0.1%,
≥5K
Ohms
3.5 at 70°C derating to 0 at 125°C
1,000V rms
1,000 Megohms
100 Ohms
356° + 1°
±1°
Linearity x Input Voltage
Operating Temperature Range
Temperature Cycling
Shock, 6ms Sawtooth
Vibration
Moisture Resistance
High Temperature Exposure
Rotational Life
Rotational Load Life
Specifications subject to change without notice.
Static: –65°C to +125°C
Dynamic: –40°C to +125°C
5 cycles, -65°C to +125°C (10%
∆R)
50G’s (0.1ms discontinuity max.)
15G’s, 10 to 2,000 Hz (5%
∆R,
0.1ms discontinuity max.)
Ten 24 hour cycles (3%
∆R)
1,000 hours at 125°C (5%
∆R)
1 Mil. Shaft Rev.
1 mil. shaft rev. at rated wattage at 70°C (5%
∆R)
2-51
Model 5610 Series
MECHANICAL
Total Mechanical Travel
Number of Gangs, Maximum
Weight, Nominal
Backlash, Maximum
Shaft End Play, Maximum
Shaft Runout, T.I.R., Maximum
Pilot Diameter Runout, T.I.R., Maximum
Lateral Runout, T.I.R., Maximum
Shaft Radial Play, Maximum
Starting Torque, Maximum (per gang)
Running Torque, Maximum (per gang)
OUTLINE DIMENSIONS (Inch/mm)
360° Continuous
4
3.7 oz. Single Gang
1.3 oz. Each Added Gang
1°
.005”
5611
5613
.0005”
.001”
.002”
.0015”
.004”
.006”
.004”
.002”
1.5 oz.-in.
0.8 oz.-in.
1.1 oz.-in.
0.6 oz.-in.
Model 5611
Bushing Mount with Sleeve Bearing
Mounting Surface
.875±.031
22.2±0.79
.375
9.53
Min.
+.0000
-.0003 Dia.
+0.000
6.342
-0.008
.2497
90° Max.
CCW
Clamp CW
Ears
Slider
1.250
R. Max.
31.75
"RS"
±.031
±0.79
"L"
2.000±.016
50.80±0.41
Dia.
1.375±.016
Dia.
34.93±0.41
+.000
-.010
+0.00
1.58
-0.25
.062
.375±.016
9.53±0.41
+.000
-.002 Dia.
+0.00
10.3
-0.05
.406
Chamfer .016 Max. x 45°
0.41
3/8 - 32 UNEF Thread
Dim. "L"
.905±.020
22.9±0.51
1.467±0.22
37.26±0.56
2.029±.024
51.54±0.61
2.591±.026
65.81±0.66
.531±.016
R.
13.5±0.41
Locating Hole
.129±.005
.062±.016
Dia. x
Deep
3.28±0.13
1.58±0.41
Positioned as shown
±
5°
Dim. "RS" No. of Cups
1.405
35.69
1.967
49.96
2.529
64.24
3.091
78.51
1
2
3
4
2-52
Model 5610 Series
OUTLINE DIMENSIONS (Inch/mm)
Model 5613
Servo Mount with Ball Bearing
"RS"
±.031
±0.79
"L"
.50
12.7
Min.
Mounting Surface
.625±.031
15.9±0.79
.010 R. Max
0.25
+.0000
-.0003
Dia.
+.000
+0.000
1.875
6.342
-.001
-0.008
+0.00
47.63
-0.03
.2497
90° Max.
Slider
CCW
Clamp CW
Ears
1.250
R. Max.
31.75
2
2.000±.016 Dia.
50.80±0.41
2.000±.005 Dia.
50.80±0.13
1.875 Dia. Max.
47.63
.073 Min.
1.85
.062±.005
1.58±0.13
.093±.005
2.36±0.13
Chamfer .016 Max. x 45°
0.41
Dim. "L"
1.020±.015
25.91±0.38
1.582±0.17
40.18±0.43
2.144±.019
54.46±0.48
2.706±.021
68.73±0.53
Dim. "RS" No. of Cups
1.520
38.61
2.082
52.88
2.644
67.16
3.206
81.43
1
2
3
4
METRIC CONVERSIONS
1 in.
1 oz.
25.4 mm
28.4 gm
1 oz.-in.
1 lb.-in.
0,007 N-m
0,113 N-m
2-53
Model Series 5610
STANDARD RESISTANCE VALUES, OHMS
Total
Resistance
1K
2K
5K
10K
20K
30K
50K
Theoretical
Resolution
(% Nominal)
0.089
0.071
0.058
0.053
0.043
0.040
0.040
* Lower tempco available as a non-standard model (consult factory).
Tempco
of Wire
*±130 ppm/°C
*±130 ppm/°C
±20 ppm/°C
±20 ppm/°C
±20 ppm/°C
± 20 ppm/°C
± 20 ppm/°C
SPECIAL FEATURES
Center Tap
Linearity Tape
Rear Shaft Extension
Flatted Shaft
Slotted Shaft
Shaft Lock (5611 only)
Additional Gangs
ORDERING INFORMATION
CT
LT
RS
FS
SS
SL
2G or 3G or 4G
5611 R 10K T2 L .50 XX
Model Series
Resistance Prefix
Resistance Value
Optional Special
Feature Code
Linearity
Optional
Non-Standard Tolerance
CIRCUIT DIAGRAM
NOTES
(S)
(CCW)
(CW)
Metric equivalents, based on 1 inch = 25.4mm are rounded to
the same number of significant figures as in the original
English units and are provided for general information only.
Tolerances unless otherwise specified:
Linear = ± .01 inches
(.25mm)
Angular = ± 2 degrees
INCH
mm
2-54
Model 5610 Series
京公网安备 11010802033920号
EEWORLD
