534CB622080BGR datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > 534CB622080BGR

Preview

534CB622080BGR: DescriptionCRYSTAL OSCILLATOR (XO) (10 MHZ TO 1.4 GHZ); File Size180KB，10 Pages; ManufacturerSILABS; Websitehttp://www.silabs.com

Download Datasheet View All

534CB622080BGR Overview

CRYSTAL OSCILLATOR (XO) (10 MHZ TO 1.4 GHZ)

Preview

Download Datasheet

View All

Si534

R E L I M I N A R Y

A TA

H E E T

R Y S TA L

S C I L L A T O R

(XO)

(10 M H

Z T O

1.4 G H

)

Features

Available with any-rate output

frequencies from 10 MHz to 945 MHz

and select frequencies to 1.4 GHz

Four selectable output frequencies

3rd generation DSPLL

with superior

jitter performance

3x better frequency stability than

SAW-based oscillators

Internal fixed crystal frequency

ensures high reliability and low

aging

Available CMOS, LVPECL,

LVDS, and CML outputs

3.3, 2.5, and 1.8 V supply options

Industry-standard 5 x 7 mm

package and pinout

Pb-free/RoHS-compliant

Si5602

Ordering Information:

See page 6.

Applications

SONET/SDH

Networking

SD/HD video

Clock and data recovery

FPGA/ASIC clock generation

Pin Assignments:

See page 5.

(Top View)

FS[1]

GND

FS[0]

Description

The Si534 quad frequency XO utilizes Silicon Laboratories’ advanced

DSPLL

circuitry to provide a low jitter clock at high frequencies. The Si534

is available with any-rate output frequency from 10 to 945 MHz and select

frequencies to 1400 MHz. Unlike a traditional XO where a different crystal is

required for each output frequency, the Si534 uses one fixed crystal to

provide a wide range of output frequencies. This IC based approach allows

the crystal resonator to provide exceptional frequency stability and reliability.

In addition, DSPLL clock synthesis provides superior supply noise rejection,

simplifying the task of generating low jitter clocks in noisy environments

typically found in communication systems. The Si534 IC-based XO is factory

configurable for a wide variety of user specifications including frequency,

supply voltage, output format, and temperature stability. Specific

configurations are factory programmed at time of shipment, thereby

eliminating long lead times associated with custom oscillators.

CLK–

CLK+

(LVDS/LVPECL/CML)

FS[1]

GND

FS[0]

Functional Block Diagram

CLK– CLK+

CLK

FS[1]

Fixed

Frequency

Any-rate

10–1400 MHz

DSPLL

Clock

Synthesis

FS[0]

(CMOS)

GND

Preliminary Rev. 0.4 5/06

Si534

This information applies to a product under development. Its characteristics and specifications are subject to change without notice.

Recommended Resources

AC electronic voltage regulator overvoltage protection circuit

Stabilized power supply overcurrent protection circuit 3a

SZ-9201 AC lantern control circuit

LED matrix drive circuit

Two types of single tone multiharmonic generating circuits

Three discharge prevention type snubber circuit IGBTs

Where is the EEFPGA reset pin?: The EEFPGA board I applied for has been made, but I didn't find the reset pin after a careful inspection. I copied the first LED lighting program of EE-FPGA, but when I assigned the pins, I didn't ass...; zw357234798 FPGA/CPLD

Transfer Huaqing Yuanjian voucher 700 yuan: Embedded training expert Huaqing Yuanjian 700 yuan voucher 300 yuan transfer (negotiable), I am an old student of Huaqing, Huaqing teacher is good, and communicates with students in time, if you can't...; shi5732 Embedded System

Learning experience of "Operational Amplifier Noise Optimization Handbook" 1: [i=s]This post was last edited by Doudou Lanyan on 2015-9-6 15:01[/i] [font=Times New Roman][size=3] A few days ago, because I had to calculate the noise level of a photodetector designed with a PMT (...; 奋斗澜颜 Analogue and Mixed Signal

Questions about the silk screen layer of PCB board: If the component identifier of the silk screen layer is set to be hidden in the PCB drawing, can the component identifier be printed when the PCB board is produced?...; soup17 PCB Design

IAR compiles a simple interrupt program with an error, please help me see how to solve it: Where the error occursError message Full code: #include void P11_Onclick() { P1OUT ^= BIT0;//Flip the level of the LED} int main( void ) { // Stop watchdog timer to prevent time out reset WDTCTL = WDT...; Krmay Microcontroller MCU

I would like to ask the experts about the CCS drawing function?: I am new to CCS. I saw that it has a drawing function. I don't have an oscilloscope, so I want to ask if I can draw the output waveform of the pin on CCS? For example, when MSP430 G2553 P1.4 outputs S...; 涅槃重生 Microcontroller MCU

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components