EEWORLDEEWORLDEEWORLD

Part Number

Search

SIT9005AIT2H-30NJ

Description
OSC MEMS
CategoryPassive components   
File Size333KB,9 Pages
ManufacturerSiTime
Environmental Compliance
Download Datasheet View All

SIT9005AIT2H-30NJ Overview

OSC MEMS

SiT9005
1 to 141 MHz EMI Reduction Oscillator
Features
Applications
Spread spectrum for EMI reduction
Wide spread % option
Center spread: from ±0.125% to ±2%, ±0.125% step size
Down spread: -0.25% to -4% with -0.25% step size
Spread profile option: Triangular, Hershey-kiss
Programmable rise/fall time for EMI reduction: 8 options,
0.25 to 40 ns
Any frequency between 1 MHz and 141 MHz accurate to
6 decimal places
100% pin-to-pin drop-in replacement to quartz-based XO’s
Excellent total frequency stability as low as ±20 ppm
Operating temperature from -40°C to 85°C.
Low power consumption of 4.0 mA typical at 1.8V
Pin1 modes: Standby, output enable, or spread disable
Fast startup time of 5 ms
LVCMOS output
Industry-standard packages
QFN: 2.0 x 1.6, 2.5 x 2.0, 3.2 x 2.5 mm
2
Contact
SiTime
for SOT23-5 (2.9 x 2.8 mm
2
)
RoHS and REACH compliant, Pb-free, Halogen-free
and Antimony-free
Surveillance camera
IP camera
Industrial motors
Flat panels
Multi function printers
PCI express
Electrical Specifications
Table 1. Electrical Characteristics
All Min and Max limits are specified over temperature and rated operating voltage with 15 pF output load unless otherwise stated.
Typical values are at 25°C and 3.3V supply voltage.
Parameters
Output Frequency Range
Symbol
Min.
Typ.
Max.
Unit
Condition
Frequency Range
f
1
141
MHz
Frequency Stability and Aging
Frequency Stability
F_stab
-20
-25
-50
Operating Temperature Range
T_use
-20
-40
Supply Voltage
Vdd
1.62
2.25
2.52
2.7
2.97
2.25
Current Consumption
OE Disable Current
Idd
I_OD
Standby Current
I_std
1.8
2.5
2.8
3.0
3.3
5.6
5.0
5.0
4.6
2.1
0.4
+20
+25
+50
+70
+85
1.98
2.75
3.08
3.3
3.63
3.63
6.5
5.5
6.5
5.2
4.3
1.5
ppm
ppm
ppm
°C
°C
V
V
V
V
V
V
mA
mA
mA
mA
µA
µA
No load condition, f = 40 MHz, Vdd = 2.5V to 3.3V
No load condition, f = 40 MHz, Vdd = 1.8V
f = 40 MHz, Vdd = 2.5V to 3.3V, OE = GND, Output in high-Z
state
f = 40 MHz, Vdd = 1.8V, OE = GND, Output in high-Z state
ST
= GND, Vdd = 2.5V to 3.3V, Output is weakly pulled down
ST
= GND, Vdd = 1.8V, Output is weakly pulled down
Inclusive of initial tolerance at 25°C, 1st year aging at 25°C, and
variations over operating temperature, rated power supply
voltage. Spread = Off.
Operating Temperature Range
Extended Commercial
Industrial
Supply Voltage and Current Consumption
Rev 1.0
September 25, 2017
www.sitime.com
About STM8 interrupt problem
After STVD builds the project, there is a file stm8_interrupt_vector.c. I built the interrupt vector and interrupt service function in it,but the question is, how do I enable and disable interrupts in...
忧乐游子 stm32/stm8
Network Development Notes 9_Access Database Basics
Why learn Access?Why learn Access? Many friends will ask curiously, aren't you talking about Lm3sxxxx 's network development? Why are you talking about Access database? Isn't this irrelevant?No, not a...
yuhua8688 Microcontroller MCU
ATMEL AT91SAM9263 development board technical exchange QQ group welcome to join
The TE9263 development board uses the ATMEL AT91SAM9263 microcontroller, which has an embedded ARM926EJ-S processor. The parallel bus architecture of this processor uses distributed DMA, thus breaking...
sypanyue Embedded System
Real-time control technologies meet the demands of real-time industrial communications - Part 2
Part 1 of this blog series introduced the market opportunity for EtherCAT slave stack solutions for C2000 microcontrollers (MCUs) and presented a three-stage guide to quickly get started with slave st...
alan000345 TI Technology Forum
TMS320F28335 ADC reference voltage problem
Hi everyone, I have a question: Is the 28335 ADC conversion result calculated according to the formula of 226380? What if the reference voltage I set is 2.048V?...
Duanming Microcontroller MCU
Regarding the timing constraints, does the chip that works normally after downloading need timing constraints?
If both the functional simulation and timing simulation pass, but the chip does not work properly after downloading it to the chip, is it necessary to make timing constraints at this time? If the enti...
瓷娃娃 FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2166  1720  608  1174  2578  44  35  13  24  52 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号