EEWORLDEEWORLDEEWORLD

Part Number

Search

SIT9005AIE1D-28NP

Description
OSC MEMS
CategoryPassive components   
File Size333KB,9 Pages
ManufacturerSiTime
Environmental Compliance
Download Datasheet View All

SIT9005AIE1D-28NP Overview

OSC MEMS

SiT9005
1 to 141 MHz EMI Reduction Oscillator
Features
Applications
Spread spectrum for EMI reduction
Wide spread % option
Center spread: from ±0.125% to ±2%, ±0.125% step size
Down spread: -0.25% to -4% with -0.25% step size
Spread profile option: Triangular, Hershey-kiss
Programmable rise/fall time for EMI reduction: 8 options,
0.25 to 40 ns
Any frequency between 1 MHz and 141 MHz accurate to
6 decimal places
100% pin-to-pin drop-in replacement to quartz-based XO’s
Excellent total frequency stability as low as ±20 ppm
Operating temperature from -40°C to 85°C.
Low power consumption of 4.0 mA typical at 1.8V
Pin1 modes: Standby, output enable, or spread disable
Fast startup time of 5 ms
LVCMOS output
Industry-standard packages
QFN: 2.0 x 1.6, 2.5 x 2.0, 3.2 x 2.5 mm
2
Contact
SiTime
for SOT23-5 (2.9 x 2.8 mm
2
)
RoHS and REACH compliant, Pb-free, Halogen-free
and Antimony-free
Surveillance camera
IP camera
Industrial motors
Flat panels
Multi function printers
PCI express
Electrical Specifications
Table 1. Electrical Characteristics
All Min and Max limits are specified over temperature and rated operating voltage with 15 pF output load unless otherwise stated.
Typical values are at 25°C and 3.3V supply voltage.
Parameters
Output Frequency Range
Symbol
Min.
Typ.
Max.
Unit
Condition
Frequency Range
f
1
141
MHz
Frequency Stability and Aging
Frequency Stability
F_stab
-20
-25
-50
Operating Temperature Range
T_use
-20
-40
Supply Voltage
Vdd
1.62
2.25
2.52
2.7
2.97
2.25
Current Consumption
OE Disable Current
Idd
I_OD
Standby Current
I_std
1.8
2.5
2.8
3.0
3.3
5.6
5.0
5.0
4.6
2.1
0.4
+20
+25
+50
+70
+85
1.98
2.75
3.08
3.3
3.63
3.63
6.5
5.5
6.5
5.2
4.3
1.5
ppm
ppm
ppm
°C
°C
V
V
V
V
V
V
mA
mA
mA
mA
µA
µA
No load condition, f = 40 MHz, Vdd = 2.5V to 3.3V
No load condition, f = 40 MHz, Vdd = 1.8V
f = 40 MHz, Vdd = 2.5V to 3.3V, OE = GND, Output in high-Z
state
f = 40 MHz, Vdd = 1.8V, OE = GND, Output in high-Z state
ST
= GND, Vdd = 2.5V to 3.3V, Output is weakly pulled down
ST
= GND, Vdd = 1.8V, Output is weakly pulled down
Inclusive of initial tolerance at 25°C, 1st year aging at 25°C, and
variations over operating temperature, rated power supply
voltage. Spread = Off.
Operating Temperature Range
Extended Commercial
Industrial
Supply Voltage and Current Consumption
Rev 1.0
September 25, 2017
www.sitime.com
Share Wince600's memory viewing tool
Because the AP has limited permissions under CE6, it is difficult to see the status of the memory in the physical address and kernel address space....
fuan1981 Embedded System
Ask about the design of aspect ratio
If I design a circuit using a 0.18um process, how do I estimate the aspect ratio of the transistor? Should I calculate by hand or use MATLAB? Please explain in detail. I would be grateful....
wljmm Analog electronics
[RVB2601 Creative Application Development] CDK installation problem
BG: CDK is installed on a virtual machine Win7. The system has only one C drive. A hard drive was added later and a new partition D was created. The following attempts were all fruitless. I am very fr...
shinykongcn XuanTie RISC-V Activity Zone
Temperature control between two points
[b]1. Experimental task[/b] Use an adjustable resistor to adjust the voltage value as the input of the simulated temperature. When the temperature is lower than 30℃, a long beep and light alarm sound ...
呱呱 DIY/Open Source Hardware
Data transmission issues of 3G protocol
I want to make a data acquisition card based on 3G protocol, but I don't know where to start. I want to ask experts for advice. If I design the hardware circuit myself, how should I choose the 3G netw...
kerong12 Embedded System
How is the temperature measurement on the LaunchPad demo calibrated?
After reading the manual, it seems that pressing the p1.3 button for the second time is for calibration. What is the calibration principle? How to calibrate to the actual temperature to display the am...
wangfuchong Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 186  2360  45  56  3  4  48  1  2  6 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号