EEWORLDEEWORLDEEWORLD

Part Number

Search

SIT8208AC-G3-18E-35.840000X

Description
-20 TO 70C, 2520, 50PPM, 1.8V, 3
CategoryPassive components   
File Size750KB,15 Pages
ManufacturerSiTime
Environmental Compliance
Download Datasheet View All

SIT8208AC-G3-18E-35.840000X Overview

-20 TO 70C, 2520, 50PPM, 1.8V, 3

SiT8208
Ultra Performance Oscillator
The Smart Timing Choice
The Smart Timing Choice
Features
Applications
Any frequency between 1 and 80 MHz accurate to 6 decimal places
100% pin-to-pin drop-in replacement to quartz-based oscillators
Ultra low phase jitter: 0.5 ps (12 kHz to 20 MHz)
Frequency stability as low as ±10 PPM
Industrial or extended commercial temperature range
LVCMOS/LVTTL compatible output
Standard 4-pin packages: 2.5 x 2.0, 3.2 x 2.5, 5.0 x 3.2,
7.0 x 5.0 mm x mm
Instant samples with
Time Machine II
and
field programmable
oscillators
Outstanding silicon reliability of 2 FIT or 500 million hour MTBF
Pb-free, RoHS and REACH compliant
Ultra short lead time
SATA, SAS, Ethernet, PCI Express, video, WiFi
Computing, storage, networking, telecom, industrial control
Electrical Characteristics
[1]
Parameter
Output Frequency Range
Frequency Stability
Symbol
f
F_stab
Min.
1
-10
-20
-25
-50
First year Aging
10-year Aging
Operating Temperature Range
T_use
F_aging
-1.5
-5
-20
-40
Supply Voltage
Vdd
1.71
2.25
2.52
2.97
Current Consumption
OE Disable Current
Idd
I_OD
Standby Current
I_std
Duty Cycle
Rise/Fall Time
Output Voltage High
Output Voltage Low
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
DC
Tr, Tf
VOH
VOL
VIH
VIL
Z_in
45
90%
70%
2
Typ.
1.8
2.5
2.8
3.3
31
29
1.2
100
Max.
80
+10
+20
+25
+50
+1.5
+5
+70
+85
1.89
2.75
3.08
3.63
33
31
31
30
70
10
55
2
10%
30%
250
Unit
MHz
PPM
PPM
PPM
PPM
PPM
PPM
°C
°C
V
V
V
V
mA
mA
mA
mA
A
A
%
ns
Vdd
Vdd
Vdd
Vdd
kΩ
MΩ
15 pF load, 10% - 90% Vdd
IOH = -6 mA, IOL = 6 mA, (Vdd = 3.3V, 2.8V, 2.5V)
IOH = -3 mA, IOL = 3 mA, (Vdd = 1.8V)
No load condition, f = 20 MHz, Vdd = 2.5V, 2.8V or 3.3V
No load condition, f = 20 MHz, Vdd = 1.8V
Vdd = 2.5V, 2.8V or 3.3V, OE = GND, output is Weakly Pulled
Down
Vdd = 1.8 V. OE = GND, output is Weakly Pulled Down
Vdd = 2.5V, 2.8V or 3.3V, ST = GND, output is Weakly Pulled
Down
Vdd = 1.8 V. ST = GND, output is Weakly Pulled Down
25°C
25°C
Extended Commercial
Industrial
Supply voltages between 2.5V and 3.3V can be supported.
Contact
SiTime
for additional information.
Inclusive of Initial tolerance at 25 °C, and variations over
operating temperature, rated power supply voltage and load
Condition
Frequency Range
Frequency Stability and Aging
Operating Temperature Range
Supply Voltage and Current Consumption
LVCMOS Output Characteristics
Input Characteristics
Pin 1, OE or ST
Pin 1, OE or ST
Pin 1, OE logic high or logic low, or ST logic high
Pin 1, ST logic low
Note:
1. All electrical specifications in the above table are specified with 15 pF output load and for all Vdd(s) unless otherwise stated.
SiTime Corporation
Rev. 1.02
990 Almanor Avenue
Sunnyvale, CA 94085
(408) 328-4400
www.sitime.com
Revised June 24, 2013
Microcontroller Technology
What is the classic circuit of the microcontroller like? I hope you can give me some suggestions. It would be best if you can give me a Protel 99se....
xouxie Embedded System
【MXCHIP Open1081】Help me figure out why the download failed?
[i=s]This post was last edited by dontium on 2014-12-5 17:41[/i] I have just installed KEIL and I am not familiar with it yet. I got the message Error: Flash Download failed - "Cortex-M3". Where shoul...
dontium RF/Wirelessly
wince gprs dialing problem
My program opens the serial port first, then writes the AT command to the serial port, and finally calls the rasdial() function to dial up. The problem now is that the dial-up is successful, but a ter...
rock_17 Embedded System
I'm looking for help with the problems I encountered while doing the sensorDemo experiment of zigbeecc2530
When doing the sensorDemo experiment of zigbeecc2530, the terminal node cannot be added to the zigbee sensor monitor software, and the terminal node interface always displays simpleAPI. What should I ...
王明伟 RF/Wirelessly
How about exchanging the AM3359 development board for an FPGA or DSP development board?
I want to exchange this AM3359 development board for an FPGA or DSP development board that requires USB 2.0 HS and LVDS interfaces. How about using E coins to get more or less? :lol:lol:lol...
littleshrimp Buy&Sell
WinCE interrupt processing--the problem of physical interrupt number and logical interrupt number
Hello everyone: I am working on interrupt processing under WinCE and I have encountered a problem. I hope you will speak up and give me some advice. During interrupt processing, the physical interrupt...
meja Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 190  824  1694  2745  129  4  17  35  56  3 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号