TRR01MZPJ8R2 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Passive components> TRR01MZPJ8R2

TRR01MZPJ8R2: DescriptionRES SMD 8.2 OHM 5% 1/16W 0402; CategoryPassive components; File Size588KB，7 Pages; ManufacturerROHM Semiconductor; Websitehttps://www.rohm.com/; Environmental Compliance

Download Datasheet Parametric View All

TRR01MZPJ8R2 Overview

RES SMD 8.2 OHM 5% 1/16W 0402

TRR01MZPJ8R2 Parametric

Parameter Name	Attribute value
resistance	8.2 Ohms
Tolerance	±5%
Power (W)	0.063W，1/16W
component	thick film
characteristic	Resistant to vulcanization
Temperature Coefficient	-250/ +500ppm/°C
Operating temperature	-55°C ~ 155°C
Package/casing	0402 (1005 Metric)
Supplier device packaging	402
size/dimensions	0.039" long x 0.020" wide (1.00mm x 0.50mm)
Height - Installation (maximum)	0.016"（0.40mm）
Number of terminals	2
failure rate	-

Preview

Download Datasheet

View All

Sulfur tolerant chip resistors

TRR series

●

Features

Datasheet

1)Special construction prevents sulfur gas penetration, significantly increasing reliability.

2)ROHM resistors have obtained ISO9001 / ISO / TS16949 certification.

●

Products

ist

Part No.

Size

Rated

power

(70

℃

)

(W)

0.063

ew om

es en

ig de

ns d

(inch)

Limiting

emperature Resistance

element T

coefficient

tolerance

voltage

(V)

(ppm /

℃

)

(%)

Resistance range

(Ω)

(mm)

TRR01

1005

0402

TRR03

1608

0603

0.10

TRR10

2012

0805

0.125

150

TRR18

3216

1206

0.25

200

±100

F ( ±1% )

+500 / -250

J ( ±5% )

±200

J ( ±5% )

Jumper type

：

Rmax = 50mΩ

±100

F ( ±1% )

±400

J ( ±5% )

±200

J ( ±5% )

Jumper type

：

Rmax = 50mΩ

±100

F ( ±1% )

±400

J ( ±5% )

±200

J ( ±5% )

Jumper type

：

Rmax = 50mΩ

F ( ±1% )

±100

±400

J ( ±5% )

±200

J ( ±5% )

Jumper type

：

Rmax = 50mΩ

≦

2.2M

1.0

≦

R<10

≦

10M

/ Imax = 1A

≦

10M

≦

R<10

≦

10M

/ Imax = 1A

≦

2.2M

1.0

≦

R<10

≦

10M

/ Imax = 2A

≦

2.2M

1.0

≦

R<10

≦

10M

/ Imax = 2A

※

Design and specifications are subject to change without notice.

Carefully check the specification sheet supplied with the product before using or ordering it.

T RR

Part No.

●

Part Number description

0 1

MZ P

Size

(mm [inch])

Packaging specifications code

Paper tape

(2mm Pitch)

Paper tape

(4mm Pitch)

Paper tape

(4mm Pitch)

Paper tape

(4mm Pitch)

TRR

(Sulfur tolerant

chip resistors)

01 (1005 [0402])

03 (1608 [0603])

10 (2012 [0805])

18 (3216 [1206])

Packaging

Part No. Code specifications Quantity

/ Reel

Resistance

tolerance

F ( ±1% )

J ( ±5% )

TRR01

TRR03

TRR10

TRR18

MZP

EZP

10,000

5,000

www.rohm.com

1/4

Operating

temperature

range

(

℃

)

(E24/96 series)

(E24 series)

(E24/96 series)

(E24 series)

(E24/96 series)

(E24 series)

(E24/96 series)

(E24 series)

-55

+155

-55

+155

-55

+155

-55

+155

1 0 5

Nominal resistance

Resistance code, 3 or 4 digits.

000 denotes jumper type.

Resistance

tolerance

：

Resistance

code

4 digits

3 digits

EX.)

1Ω = 1R0 ( ±5% )

9.1Ω = 9R1 ( ±5% )

10Ω = 10R0 ( ±1% )

100 ( ±5% )

1MΩ = 1004 ( ±1% )

105 ( ±5% )

2014.12 - Rev.C

Datasheet

Notice

Precaution on using ROHM Products

1. If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment

(Note 1)

aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life,

bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales

representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way

responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of

any ROHM’s Products for Specific Applications.

(Note1) Medical Equipment Classification of the Specific Applications

JAPAN

USA

CHINA

CLASS

Ⅲ

CLASS

Ⅱ

CLASS

Ⅲ

CLASS

Ⅲ

CLASS

Ⅳ

CLASS

Ⅲ

2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor

products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities,

adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any

property, which a failure or malfunction of our Products may cause. The following are examples of safety measures:

[a] Installation of protection circuits or other protective devices to improve system safety

[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure

Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below.

Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from

the use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use

our Products under any special or extraordinary environments or conditions (as exemplified below), your

independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary:

[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents

[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust

[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including

Cl2, H2S, NH3, SO2, and NO2

[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves

[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items

[f] Sealing or coating our Products with resin or other coating materials

[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue

of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for

cleaning residue after soldering

[h] Use of the Products in places subject to dew condensation

The Products are not subject to radiation-proof design.

Please verify and confirm characteristics of the final or mounted products in using the Products.

In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,

confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power

exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively

affect product performance and reliability.

De-rate Power Dissipation (Pd) depending on Ambient temperature (T When used in sealed area, confirm the

a).

actual ambient temperature.

Confirm that operation temperature is within the specified range described in the product specification.

ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined

in this document.

Precaution for Mounting / Circuit board design

1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect

product performance and reliability.

In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must

be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,

please consult with the ROHM representative in advance.

For details, please refer to ROHM Mounting specification

Notice-PAA-E

ew om

es en

ig de

ns d

Rev.001

Recommended Resources

Novel small power DC motor speed regulating circuit

RTD sensor and 24-bit AD7711A circuit

Two chip FM stereo radio

Adjustable voltage control part circuit diagram

Toy model road sign indicating circuit

Safe and reliable delay switch circuit

How to deal with severe overheating of the adjustable DCDC circuit?: I've been working on a commonly used DCDC circuit recently. How do I deal with the overheating? Isn't the LM2576 capable of outputting 3A of current? Why is it generating a fever at 900ma? When the ci...; Knight97538 Power technology

c# Question about rfid reading: My RFID can read the serial number in the RFID card and output it to the computer through PS/2, which is equivalent to automatic keyboard input. How can I read it using C#? The product says that the c...; 碧海沉天 Embedded System

DAC0832 maximum output voltage is related to the applied voltage? Why?: I have been working on the ADC and DAC of MSP430 recently. The schematic diagram of DAC0832 is as follows. When I tested it, I found that when the chip voltage VCC=5V, Vref=5V, after passing through t...; eemingtian Microcontroller MCU

What is the difference between Xiangyang No. 1 fuel consumption GPS and ordinary GPS?: Beijing Xiangyangtian Technology Co., Ltd. ([url=http://www.xiangyangtian.com]www.xiangyangtian.com[/url]) is a professional company engaged in the research and development and application of data tra...; bjxiangyangtian Automotive Electronics

LPC800 development board I2C enabling problem.: I modified the I2C_EEPROM program in the I2C in Zhou Ligong's LPC800 example, but it still doesn't work. Please help me take a look. void I2CInit (void) { //The original program uses the most suitable...; hizzx NXP MCU

XILINX ISE14.6 fails to generate bitstream: The synthesis, routing, etc. of the design can all be passed. When generating the bitstream, the following error will be displayed: ERROR:PhysDesignRules:1383 - Issue with pin connections and/or confi...; daiwenzhou FPGA/CPLD

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components