EEWORLDEEWORLDEEWORLD

Part Number

Search

SIT9005AIB1G-33DN

Description
OSC MEMS
CategoryPassive components   
File Size333KB,9 Pages
ManufacturerSiTime
Environmental Compliance
Download Datasheet View All

SIT9005AIB1G-33DN Overview

OSC MEMS

SiT9005
1 to 141 MHz EMI Reduction Oscillator
Features
Applications
Spread spectrum for EMI reduction
Wide spread % option
Center spread: from ±0.125% to ±2%, ±0.125% step size
Down spread: -0.25% to -4% with -0.25% step size
Spread profile option: Triangular, Hershey-kiss
Programmable rise/fall time for EMI reduction: 8 options,
0.25 to 40 ns
Any frequency between 1 MHz and 141 MHz accurate to
6 decimal places
100% pin-to-pin drop-in replacement to quartz-based XO’s
Excellent total frequency stability as low as ±20 ppm
Operating temperature from -40°C to 85°C.
Low power consumption of 4.0 mA typical at 1.8V
Pin1 modes: Standby, output enable, or spread disable
Fast startup time of 5 ms
LVCMOS output
Industry-standard packages
QFN: 2.0 x 1.6, 2.5 x 2.0, 3.2 x 2.5 mm
2
Contact
SiTime
for SOT23-5 (2.9 x 2.8 mm
2
)
RoHS and REACH compliant, Pb-free, Halogen-free
and Antimony-free
Surveillance camera
IP camera
Industrial motors
Flat panels
Multi function printers
PCI express
Electrical Specifications
Table 1. Electrical Characteristics
All Min and Max limits are specified over temperature and rated operating voltage with 15 pF output load unless otherwise stated.
Typical values are at 25°C and 3.3V supply voltage.
Parameters
Output Frequency Range
Symbol
Min.
Typ.
Max.
Unit
Condition
Frequency Range
f
1
141
MHz
Frequency Stability and Aging
Frequency Stability
F_stab
-20
-25
-50
Operating Temperature Range
T_use
-20
-40
Supply Voltage
Vdd
1.62
2.25
2.52
2.7
2.97
2.25
Current Consumption
OE Disable Current
Idd
I_OD
Standby Current
I_std
1.8
2.5
2.8
3.0
3.3
5.6
5.0
5.0
4.6
2.1
0.4
+20
+25
+50
+70
+85
1.98
2.75
3.08
3.3
3.63
3.63
6.5
5.5
6.5
5.2
4.3
1.5
ppm
ppm
ppm
°C
°C
V
V
V
V
V
V
mA
mA
mA
mA
µA
µA
No load condition, f = 40 MHz, Vdd = 2.5V to 3.3V
No load condition, f = 40 MHz, Vdd = 1.8V
f = 40 MHz, Vdd = 2.5V to 3.3V, OE = GND, Output in high-Z
state
f = 40 MHz, Vdd = 1.8V, OE = GND, Output in high-Z state
ST
= GND, Vdd = 2.5V to 3.3V, Output is weakly pulled down
ST
= GND, Vdd = 1.8V, Output is weakly pulled down
Inclusive of initial tolerance at 25°C, 1st year aging at 25°C, and
variations over operating temperature, rated power supply
voltage. Spread = Off.
Operating Temperature Range
Extended Commercial
Industrial
Supply Voltage and Current Consumption
Rev 1.0
September 25, 2017
www.sitime.com
Research on High Dynamic Signal Conditioning Circuit
Realize three-way signal input connection;Input signal frequency 0.1~100Hz;Input signal amplitude 1mV~10V;Input signal amplitude 0°~180°;Realize input signal noise reduction processing;Realize 0~20V s...
ZYN931220 ADI Reference Circuit
Power supply switching problem
The system is powered by an external DC5V power supply and a 3.7V lithium battery. When the DC5V is plugged in, the lithium battery does not supply power, but needs to be charged; when the DC5V is unp...
ly6277895 Analogue and Mixed Signal
[AT-START-F403A Evaluation] 4. FreeRTOS system based on IAR environment external flash (SPIM) operation evaluation
The last evaluation achieved a rough test of the performance of the external SPIM QSPI Flash. This evaluation will divide the external flash into two parts:0x08400000-0x0840FFFF is used as the data ar...
uuxz99 Domestic Chip Exchange
spi communication
I would like to ask the forum owner, when I use SPI communication, I use the DMA+DMA interrupt+CRC check method to send and receive 8-bit data. I would like to know how the final CRC is transmitted an...
shortt stm32/stm8
[STM32F769 Review] --STM32F769Discovery Unboxing Experience
[i=s]This post was last edited by DavidZH on 2016-12-10 20:52[/i] [size=5]Unboxing experience:[/size] [align=left]The long-awaited [font=Times New Roman, serif]STM32F7Discovery[/font] finally arrived ...
DavidZH stm32/stm8
Problems with writing USB drivers with WDF...
I am currently learning to use WDF to develop a USB interface driver for a board. I mainly want to complete the function of interrupt transmission. I modified an example provided by Microsoft and comp...
coolgreen1 Programming Basics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1819  1936  2042  930  1180  37  39  42  19  24 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号