SIT8208AC-32-18S-12.000000T datasheet, PDF

Datasheet> All Categories > Passive components> SIT8208AC-32-18S-12.000000T

Preview

SIT8208AC-32-18S-12.000000T: Description-20 TO 70C, 5032, 25PPM, 1.8V, 1; CategoryPassive components; File Size750KB，15 Pages; ManufacturerSiTime; Environmental Compliance

Download Datasheet View All

SIT8208AC-32-18S-12.000000T Overview

-20 TO 70C, 5032, 25PPM, 1.8V, 1

Preview

Download Datasheet

View All

SiT8208

Ultra Performance Oscillator

The Smart Timing Choice

Features



Applications



Any frequency between 1 and 80 MHz accurate to 6 decimal places

100% pin-to-pin drop-in replacement to quartz-based oscillators

Ultra low phase jitter: 0.5 ps (12 kHz to 20 MHz)

Frequency stability as low as ±10 PPM

Industrial or extended commercial temperature range

LVCMOS/LVTTL compatible output

Standard 4-pin packages: 2.5 x 2.0, 3.2 x 2.5, 5.0 x 3.2,

7.0 x 5.0 mm x mm

Instant samples with

Time Machine II

and

field programmable

oscillators

Outstanding silicon reliability of 2 FIT or 500 million hour MTBF

Pb-free, RoHS and REACH compliant

Ultra short lead time

SATA, SAS, Ethernet, PCI Express, video, WiFi

Computing, storage, networking, telecom, industrial control

Electrical Characteristics

[1]

Parameter

Output Frequency Range

Frequency Stability

Symbol

F_stab

Min.

-10

-20

-25

-50

First year Aging

10-year Aging

Operating Temperature Range

T_use

F_aging

-1.5

-5

-20

-40

Supply Voltage

Vdd

1.71

2.25

2.52

2.97

Current Consumption

OE Disable Current

Idd

I_OD

–

Standby Current

I_std

–

Duty Cycle

Rise/Fall Time

Output Voltage High

Output Voltage Low

Input Voltage High

Input Voltage Low

Input Pull-up Impedance

Tr, Tf

VOH

VOL

VIH

VIL

Z_in

–

90%

–

70%

–

Typ.

–

1.8

2.5

2.8

3.3

–

1.2

–

100

–

Max.

+10

+20

+25

+50

+1.5

+70

+85

1.89

2.75

3.08

3.63

–

10%

–

30%

250

–

Unit

MHz

PPM

°C

A

Vdd

kΩ

MΩ

15 pF load, 10% - 90% Vdd

IOH = -6 mA, IOL = 6 mA, (Vdd = 3.3V, 2.8V, 2.5V)

IOH = -3 mA, IOL = 3 mA, (Vdd = 1.8V)

No load condition, f = 20 MHz, Vdd = 2.5V, 2.8V or 3.3V

No load condition, f = 20 MHz, Vdd = 1.8V

Vdd = 2.5V, 2.8V or 3.3V, OE = GND, output is Weakly Pulled

Down

Vdd = 1.8 V. OE = GND, output is Weakly Pulled Down

Vdd = 2.5V, 2.8V or 3.3V, ST = GND, output is Weakly Pulled

Down

Vdd = 1.8 V. ST = GND, output is Weakly Pulled Down

25°C

Extended Commercial

Industrial

Supply voltages between 2.5V and 3.3V can be supported.

Contact

SiTime

for additional information.

Inclusive of Initial tolerance at 25 °C, and variations over

operating temperature, rated power supply voltage and load

Condition

Frequency Range

Frequency Stability and Aging

Operating Temperature Range

Supply Voltage and Current Consumption

LVCMOS Output Characteristics

Input Characteristics

Pin 1, OE or ST

Pin 1, OE logic high or logic low, or ST logic high

Pin 1, ST logic low

Note:

1. All electrical specifications in the above table are specified with 15 pF output load and for all Vdd(s) unless otherwise stated.

SiTime Corporation

Rev. 1.02

990 Almanor Avenue

Sunnyvale, CA 94085

(408) 328-4400

www.sitime.com

Revised June 24, 2013

Recommended Resources

Touch type self-extinguishing circuit

High input impedance differential amplifier

Micro infrared receiver module PIC-12043S circuit diagram

Use a multimeter to measure the head and tail of the three-phase winding of the motor

Voltage follower circuit with overvoltage protection

Low resistance power distribution circuit

The pants are coming~~~ A fully handmade ARM9 (2410) application board: Top layer: [img]http://bbs.21ic.com/upfiles/img/20081/2008123233735447.jpg[/img] Bottom layer: [img]http://bbs.21ic.com/upfiles/img/20081/2008123233850646.jpg[/img]...; awey PCB Design

Can the EVC simulator communicate with the GPRS module on the PC serial port?: Can the EVC simulator communicate with the GPRS module on the PC serial port? Has anyone done a similar communication between the simulator and the device on the PC serial port?...; jgj Embedded System

Xiaobai asks questions (2): I have another question. The signal components after detection and DC blocking capacitor are () A: AM wave, low frequency, DC B: constant amplitude carrier and upper and lower sidebands C: constant am...; RFjohn RF/Wirelessly

Electronic Transformer: Help: Where can I buy the model of an electronic transformer that converts 220V AC to 110V AC 20A? Or can I get the circuit diagram of the electronic transformer? Thank you!...; kind Power technology

Why Use a 24-Bit Converter Instead of Multiple 12-Bit Devices: In portable medical devices and industrial automation involving temperature measurement, pressure measurement, industrial process control, 12-bit converters are ideal. However, if you consider the ent...; Jacktang Analogue and Mixed Signal

Maybe it's malicious code!: Recently, when I turn on my computer, the following web pages will pop up automatically every few minutes: [url]http://www.it234.com/html/food_and_drink/index.html[/url] [url]http://www.5ctc.cn/[/url]...; huchuan987 Embedded System

Shortcut: 00 01 02 03 04 05 06 07 08 09 0A 0C 0F 0J 0L 0M 0R 0S 0T 0Z 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 1H 1K 1M 1N 1P 1S 1T 1V 1X 1Z 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 2G 2K 2M 2N 2P 2Q 2R 2S 2T 2W 2Z 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 3G 3H 3J 3K 3L 3M 3N 3P 3R 3S 3T 3V 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4M 4N 4P 4S 4T 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5E 5G 5H 5K 5M 5N 5P 5S 5T 5V 60 61 62 63 64 65 66 67 68 69 6A 6C 6E 6F 6M 6N 6P 6R 6S 6T 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7M 7N 7P 7Q 7V 7W 7X 80 81 82 83 84 85 86 87 88 89 8A 8D 8E 8L 8N 8P 8S 8T 8W 8Y 8Z 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9F 9G 9H 9L 9S 9T 9W

Popular Components