EEWORLDEEWORLDEEWORLD

Part Number

Search

SIT8208AC-G2-28E-75.000000Y

Description
-20 TO 70C, 2520, 25PPM, 2.8V, 7
CategoryPassive components   
File Size750KB,15 Pages
ManufacturerSiTime
Environmental Compliance
Download Datasheet View All

SIT8208AC-G2-28E-75.000000Y Overview

-20 TO 70C, 2520, 25PPM, 2.8V, 7

SiT8208
Ultra Performance Oscillator
The Smart Timing Choice
The Smart Timing Choice
Features
Applications
Any frequency between 1 and 80 MHz accurate to 6 decimal places
100% pin-to-pin drop-in replacement to quartz-based oscillators
Ultra low phase jitter: 0.5 ps (12 kHz to 20 MHz)
Frequency stability as low as ±10 PPM
Industrial or extended commercial temperature range
LVCMOS/LVTTL compatible output
Standard 4-pin packages: 2.5 x 2.0, 3.2 x 2.5, 5.0 x 3.2,
7.0 x 5.0 mm x mm
Instant samples with
Time Machine II
and
field programmable
oscillators
Outstanding silicon reliability of 2 FIT or 500 million hour MTBF
Pb-free, RoHS and REACH compliant
Ultra short lead time
SATA, SAS, Ethernet, PCI Express, video, WiFi
Computing, storage, networking, telecom, industrial control
Electrical Characteristics
[1]
Parameter
Output Frequency Range
Frequency Stability
Symbol
f
F_stab
Min.
1
-10
-20
-25
-50
First year Aging
10-year Aging
Operating Temperature Range
T_use
F_aging
-1.5
-5
-20
-40
Supply Voltage
Vdd
1.71
2.25
2.52
2.97
Current Consumption
OE Disable Current
Idd
I_OD
Standby Current
I_std
Duty Cycle
Rise/Fall Time
Output Voltage High
Output Voltage Low
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
DC
Tr, Tf
VOH
VOL
VIH
VIL
Z_in
45
90%
70%
2
Typ.
1.8
2.5
2.8
3.3
31
29
1.2
100
Max.
80
+10
+20
+25
+50
+1.5
+5
+70
+85
1.89
2.75
3.08
3.63
33
31
31
30
70
10
55
2
10%
30%
250
Unit
MHz
PPM
PPM
PPM
PPM
PPM
PPM
°C
°C
V
V
V
V
mA
mA
mA
mA
A
A
%
ns
Vdd
Vdd
Vdd
Vdd
kΩ
MΩ
15 pF load, 10% - 90% Vdd
IOH = -6 mA, IOL = 6 mA, (Vdd = 3.3V, 2.8V, 2.5V)
IOH = -3 mA, IOL = 3 mA, (Vdd = 1.8V)
No load condition, f = 20 MHz, Vdd = 2.5V, 2.8V or 3.3V
No load condition, f = 20 MHz, Vdd = 1.8V
Vdd = 2.5V, 2.8V or 3.3V, OE = GND, output is Weakly Pulled
Down
Vdd = 1.8 V. OE = GND, output is Weakly Pulled Down
Vdd = 2.5V, 2.8V or 3.3V, ST = GND, output is Weakly Pulled
Down
Vdd = 1.8 V. ST = GND, output is Weakly Pulled Down
25°C
25°C
Extended Commercial
Industrial
Supply voltages between 2.5V and 3.3V can be supported.
Contact
SiTime
for additional information.
Inclusive of Initial tolerance at 25 °C, and variations over
operating temperature, rated power supply voltage and load
Condition
Frequency Range
Frequency Stability and Aging
Operating Temperature Range
Supply Voltage and Current Consumption
LVCMOS Output Characteristics
Input Characteristics
Pin 1, OE or ST
Pin 1, OE or ST
Pin 1, OE logic high or logic low, or ST logic high
Pin 1, ST logic low
Note:
1. All electrical specifications in the above table are specified with 15 pF output load and for all Vdd(s) unless otherwise stated.
SiTime Corporation
Rev. 1.02
990 Almanor Avenue
Sunnyvale, CA 94085
(408) 328-4400
www.sitime.com
Revised June 24, 2013
Linux driver development learning steps
1. Learn to write a simple makefile 2. Write an application that can be run with makefile 3. Learn to write a driver makefile 4. Write a simple char driver, makefile compiled, can be insmod, lsmod, rm...
educn721521 Linux and Android
Launchpadi Learning + Original Routines
After getting the lauchpad , I never looked at the example program on the board. Today I had some time to study it. 1. Downloadthe GUI interface according to the link in the experimental instruction b...
billjing Microcontroller MCU
MSP430G2 Development Board Learning (VIII): Timer A Upward Growth Mode
//************************************************ **************************** // MSP430F20xx Demo - Timer_A, Toggle P1.0, CCR0 Up Mode ISR, DCO SMCLK / // // Description: Toggle P1.0 using software ...
lilong8470 Microcontroller MCU
I want to ask what kind of signal the OUT (below the 3.3V input resistor) in the figure will output, and whether the second one can be removed...
As the title says: What kind of signal will the OUT (below the 3.3V input resistor) in the figure output? Also, can the second optocoupler be removed? Thank you....
cuiguifu Analog electronics
TI promotional delivery issues
A few days ago, I received an email from TI saying that the "Bluetooth Smart Development Kit" I bought was shipped, but there was no tracking number on it. The shipping email of my other watch showed ...
xscc TI Technology Forum
How can I see the assembly information in ATMANAVR?
I am frustrated. I defined a structure variable, but I can't find its corresponding register. When I added the variable in DEBUG, WATCH shows SYMBOL IS NOT FOUND! Brothers and sisters, please help me ...
XWXWANG Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1102  1866  1520  310  2237  23  38  31  7  46 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号