......................................................................................................... -0.6V to V
CC
+1.0V
Storage temperature ...............................................................................................................................-65°C to +150°C
Ambient temperature with power applied ................................................................................................-40°C to +125°C
ESD protection on all pins ..........................................................................................................................................4 kV
† NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to
the device. This is a stress rating only and functional operation of the device at those or any other conditions
above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating
conditions for extended periods may affect device reliability.
TABLE 1-1:
DC CHARACTERISTICS
Industrial (I):
Automotive (E)
Symbol
V
IH
V
IL
V
HYS
V
OL
I
LI
I
LO
C
IN
,
C
OUT
I
CC
Write
I
CC
Read
I
CCS
T
A
= -40°C to +85°C,
T
A
= -40°C to +125°C,
Max.
—
0.3 V
CC
—
0.4
±1
±1
10
2
1
1
Units
V
V
V
V
A
A
pF
mA
mA
A
(Note)
(Note)
V
CC
2.5V
(Note)
I
OL
= 3.0 mA, V
CC
= 4.5V
I
OL
= 2.1 mA, V
CC
= 2.5V
V
IN
= V
CC
or V
SS
V
OUT
= V
CC
or V
SS
V
CC
= 5.0V
(Note)
T
A
= 25°C, F
CLK
= 1 MHz
V
CC
= 5.5V, SCL = 400 kHz
V
CC
= 5.5V, SCL = 400 kHz
V
CC
= 5.5V, SDA = SCL = V
CC
V
CC
= 1.8V to 5.5V
V
CC
= 4.5V to 5.5V
Conditions
All Parameters apply across the
recommended operating ranges unless
otherwise noted
Parameter
SCL and SDA pins:
High-level input voltage
Low-level input voltage
Hysteresis of Schmitt Trigger
inputs
Low-level output voltage
Input leakage current
Output leakage current
Pin capacitance (all inputs/outputs)
Operating current
Standby current
Note:
Min.
0.7 V
CC
—
.05 V
CC
—
—
—
—
—
—
—
This parameter is periodically sampled and not 100% tested.
FIGURE 1-1:
BUS TIMING DATA
T
F
T
HIGH
T
R
SCL
T
SU
:
STA
T
LOW
T
HD
:
DAT
T
SU
:
DAT
T
SU
:
STO
SDA
IN
T
SP
T
HD
:
STA
T
AA
T
BUF
SDA
OUT
DS20001178J-page 2
1996-2018 Microchip Technology Inc.
24AA00/24LC00/24C00
TABLE 1-2:
AC CHARACTERISTICS
Industrial (I):
Automotive (E):
Symbol
F
CLK
Min
—
—
—
4000
4000
600
4700
4700
1300
—
—
—
—
4000
4000
600
4700
4700
600
0
250
250
100
4000
4000
600
—
—
—
4700
4700
1300
20+0.1
CB
—
—
1M
T
A
= -40°C to +85°C, V
CC
= 1.8V to 5.5V
T
A
= -40°C to +125°C, V
CC
= 4.5V to 5.5V
Max
100
100
400
—
—
—
—
—
—
1000
1000
300
300
—
—
—
—
—
—
—
—
—
—
—
—
—
3500
3500
900
—
—
—
250
50
4
—
Units
kHz
Conditions
4.5V
Vcc
5.5V (E Temp range)
1.8V
Vcc 4.5V
4.5V
Vcc
5.5V
4.5V
Vcc
5.5V (E Temp range)
1.8V
Vcc 4.5V
4.5V
Vcc
5.5V
4.5V
Vcc
5.5V (E Temp range)
1.8V
Vcc 4.5V
4.5V
Vcc
5.5V
4.5V
Vcc
5.5V (E Temp range)
1.8V
Vcc 4.5V
4.5V
Vcc
5.5V
(Note
1)
4.5V
Vcc
5.5V (E Temp range)
1.8V
Vcc 4.5V
4.5V
Vcc
5.5V
4.5V
Vcc
5.5V (E Temp range)
1.8V
Vcc 4.5V
4.5V
Vcc
5.5V
(Note
2)
4.5V
Vcc
5.5V (E Temp range)
1.8V
Vcc 4.5V
4.5V
Vcc
5.5V
4.5V
Vcc
5.5V (E Temp range)
1.8V
Vcc 4.5V
4.5V
Vcc
5.5V
4.5V
Vcc
5.5V (E Temp range)
1.8V
Vcc 4.5V
4.5V
Vcc
5.5V
4.5V
Vcc
5.5V (E Temp range)
1.8V
Vcc 4.5V
4.5V
Vcc
5.5V
(Note
1),
CB
100
pF
(Notes
1, 3)
All Parameters apply across all
recommended operating ranges
unless otherwise noted
Parameter
Clock frequency
Clock high time
T
HIGH
ns
Clock low time
T
LOW
ns
SDA and SCL rise time
(Note
1)
SDA and SCL fall time
Start condition hold time
T
R
ns
T
F
T
HD
:
STA
ns
ns
Start condition setup time
T
SU
:
STA
ns
Data input hold time
Data input setup time
T
HD
:
DAT
T
SU
:
DAT
ns
ns
Stop condition setup time
T
SU
:
STO
ns
Output valid from clock
(Note
2)
T
AA
ns
Bus free time: Time the bus must T
BUF
be free before a new transmis-
sion can start
Output fall time from V
IH
minimum to V
IL
maximum
Input filter spike suppression
(SDA and SCL pins)
Write cycle time
Endurance
Note 1:
2:
3:
4:
T
OF
T
SP
T
WC
ns
ns
ns
ms
cycles
(Note
4)
Not 100% tested. C
B
= total capacitance of one bus line in pF.
As a transmitter, the device must provide an internal minimum delay time to bridge the undefined region
(minimum 300 ns) of the falling edge of SCL to avoid unintended generation of Start or Stop conditions.
The combined T
SP
and V
HYS
specifications are due to new Schmitt Trigger inputs which provide improved
noise spike suppression. This eliminates the need for a TI specification for standard operation.
This parameter is not tested but ensured by characterization. For endurance estimates in a specific
application, please consult the Total Endurance™ Model which can be obtained at www.microchip.com.
1996-2018 Microchip Technology Inc.
DS20001178J-page 3
24AA00/24LC00/24C00
2.0
PIN DESCRIPTIONS
PDIP
1, 2, 3, 7
4
5
6
8
SOIC
1, 2, 3, 7
4
5
6
8
TSSOP
1, 2, 3, 7
4
5
6
8
DFN
(1)
1, 2, 3, 7
4
5
6
8
TDFN
(1)
1, 2, 3, 7
4
5
6
8
SOT-23
4
2
3
1
5
Ground
Serial Address/Data I/O
Serial Clock
+1.8V to 5.5V Power Supply
Description
Not Connected
Pin Function Table
Name
NC
V
SS
SDA
SCL
V
CC
Note 1:
The exposed pad on the DFN/TDFN packages can be connected to V
SS
or left floating.
2.1
SDA Serial Data
This is a bidirectional pin used to transfer addresses
and data into and data out of the device. It is an open
drain terminal, therefore the SDA bus requires a pull-up
resistor to V
CC
(typical 10 k for 100 kHz, 2 k for
400 kHz).
For normal data transfer SDA is allowed to change only
during SCL low. Changes during SCL high are
reserved for indicating the Start and Stop conditions.
2.2
SCL Serial Clock
This input is used to synchronize the data transfer from
and to the device.
2.3
Noise Protection
The SCL and SDA inputs have Schmitt Trigger and
filter circuits which suppress noise spikes to assure
proper device operation even on a noisy bus.
DS20001178J-page 4
1996-2018 Microchip Technology Inc.
24AA00/24LC00/24C00
3.0
FUNCTIONAL DESCRIPTION
4.0
BUS CHARACTERISTICS
The 24XX00 supports a bidirectional 2-wire bus and
data transmission protocol. A device that sends data
onto the bus is defined as a transmitter, and a device
receiving data as a receiver. The bus has to be
controlled by a master device which generates the
Serial Clock (SCL), controls the bus access, and
generates the Start and Stop conditions, while the
24XX00 works as slave. Both master and slave can
operate as transmitter or receiver, but the master
device determines which mode is activated.
The following
bus protocol
has been defined:
• Data transfer may be initiated only when the bus
is not busy.
• During data transfer, the data line must remain
stable whenever the clock line is high. Changes in
the data line while the clock line is high will be
interpreted as a Start or Stop condition.
Accordingly, the following bus conditions have been
defined (Figure
4-1).
4.1
Bus Not Busy (A)
Both data and clock lines remain high.
4.2
Start Data Transfer (B)
A high-to-low transition of the SDA line while the clock
(SCL) is high determines a Start condition. All
commands must be preceded by a Start condition.
4.3
Stop Data Transfer (C)
A low-to-high transition of the SDA line while the clock
(SCL) is high determines a Stop condition. All
operations must be ended with a Stop condition.
4.4
Data Valid (D)
The state of the data line represents valid data when,
after a Start condition, the data line is stable for the
duration of the high period of the clock signal.
The data on the line must be changed during the low
period of the clock signal. There is one bit of data per
clock pulse.
Each data transfer is initiated with a Start condition and
terminated with a Stop condition. The number of the
data bytes transferred between the Start and Stop
conditions is determined by the master device and is
There have been 335 commits since the last release on September 2, 2021, averaging about 2.5 commits per day.The full changelog can be found at https://micropython.org/resources/micropython-ChangeLog....
The last day to apply, the Allwinner R329 development board worth 299 yuan is waiting for you to take away, let's play togetherhow to apply
(1) ReadR329 Tutorial 1 | Zhouyi AIPU Deployment and Simulat...
I would like to ask you a question:Can I output ACLK on other IO pins? For example, P6.0?If not, if I want to output a clock signal on a pin, can I only use timerA?:confused::confused:...
introduction
In the discharge process of tokamak plasma physics, the study of rupture and sawtooth is of great significance. Rupture and sawtooth exist in most tokamaks. Rupture is a notew...[Details]
AD8205 is
a single-supply high-performance differential
amplifier
launched by
Analog
Devices of the United States
. The typical single-supply voltage is 5V, and its common-mode volta...[Details]
General LED lighting has a current limiting resistor in the driving circuit, and the power consumed by the resistor has nothing to do with the LED light emission. In order to improve efficiency, a...[Details]
VP2188 is a color STN LCD module produced by Jingdian Pengyuan. This module is a dot matrix transmissive color STN display screen with a color scale of 65 k colors and white LED backlight. Its core...[Details]
Problems such as the depletion of natural resources, air pollution, traffic congestion, and rising fossil fuel prices have forced societies and individuals to seek alternative means of transportati...[Details]
OC faults may be the most frequent and the most frequent of all faults in the inverter. They alarm during the startup process, during the shutdown process, during operation, and even when powered o...[Details]
Motors, especially those with brushes, generate a lot of noise. This noise must be dealt with if the appliance is to meet the requirements of EMC standards. The means to solve EMC are nothing more ...[Details]
According to the Industrial Technology Research Institute of Taiwan, due to factors such as the oil crisis and global warming, the issues of energy conservation and environmental protection have at...[Details]
hint:
The number of speakers and their spacing limit the sound field of a portable stereo system.
Spatial audio attempts to artificially recreate the experience of listening to sounds i...[Details]
The TPS92210 is a single-stage LED lighting pulse width modulation (PWM) controller. The TRIAC dimmable solution not only regulates the LED current, but also achieves a power factor close to 1. The...[Details]
Preface
In recent years, white light LEDs have gradually replaced incandescent bulbs and fluorescent lamps because they have unparalleled advantages over traditional light sources in terms...[Details]
The serial interface real-time clock chip DS1302 launched by Dallas Company in the United States can trickle charge the backup battery of the clock chip. Due to the main features of the chip such a...[Details]
1 Basic Features
In computer control systems and various intelligent instruments and meters composed of single-chip microcomputers (or microprocessors), various external analog signals must be ...[Details]
Introduction
As the country increases its efforts to control the atmospheric environment, motorcycle emission regulations will become stricter year by year, and motorcycles that do not meet the...[Details]
0 Introduction
With the rapid development of social economy and science and technology, electric locomotives, subways and electric vehicles will be widely used. The power conversion and cont...[Details]
MicroPython Open Source section
京公网安备 11010802033920号
EEWORLD
