EEWORLDEEWORLDEEWORLD

Part Number

Search

UMP1C-S2E-S2L-S2L-S2L-S2L-S2Y-00-A

Description
UMP CONFIGURABLE POWER SUPPLY
CategoryPower/power management   
File Size1MB,6 Pages
ManufacturerArtesyn
Websitehttp://www.artesyn.com
Environmental Compliance
Download Datasheet View All

UMP1C-S2E-S2L-S2L-S2L-S2L-S2Y-00-A Overview

UMP CONFIGURABLE POWER SUPPLY

Embedded Power for
Business-Critical Continuity
µMP Series
Up to 1200 Watts
Total Power:
Up to 1200 Watts
Input Voltage:
85 - 264 Vac
120-300 Vdc
# of Outputs:
Up to 12
MicroMP 1U Multi Output
Rev. 12.12.2013
µMP
Series
1 of 6
Special Features
Full Medical EN60601 approval
• PMBus
• High efficiency
• Current limit modification
(foldback or constant current)
• High power density.
uMP4: 10.8 W/cu-in
uMP1: 15.1 W/cu-in
• Intelligent fan
(speed control/fault status)
• Downloadable GUI from website
• uP controlled PFC input with active
inrush protection
• Optional conformal coating
• Industrial temp range (-40 ºC
to 70
ºC)
• No preload required
• Industrial shock/vibration (> 50G’s)
• Low cost
• IEC or terminal block input
• Low profile 1U size
Electrical Specifications
Input
Input range:
Frequency:
Inrush current:
Efficiency:
Power Factor:
Turn-on time:
EMI filter:
Leakage current:
Radiated EMI:
Holdover storage:
AC OK:
Harmonic distortion:
Isolation:
Input fuse (internal):
Warranty:
47 - 440 Hz
40 A peak max. (soft start)
Up to 91% @ full case load
µMP4C shown
85 - 264 Vac, 120 - 350 Vdc (limited to 250 Vac/300 Vdc in medical apps)
0.99 typ. meets EN61000-3-2 (n/a @ 440 Hz)
AC on 2 sec for uMP1 and 1.5 sec for uMP4, inhibit/enable 250 ms typical
CISPR 22/EN55022 Level “B”
300 µA Max. @ 240 VAC
CISPR 22/EN55022 Level “B”
16.7 ms minimum (independent of input Vac, 0 °C to 50 °C))
Signal goes low indicating loss of AC input.
Hold up = Full cycle ride thru (50 Hz)
Meets EN61000-3-2
Meets EN60950 and EN60601
uMP1: 16 A/250 V TLAG, uMP4: 10 A / 250 V. (both lines fused)
2 years
Global Inhibit/Enable: TTL, Logic “1” and Logic “0”; fan off when unit is inhibited
Environmental Specifications
Safety
UL
CSA
VDE
BABT
UL60950/UL60601-1
CSA22.2 No. 234 Level 5
EN60950/EN60601-1
Compliance to
EN60950/EN60601 BS7002
Certificate and report
Mark to LVD
Approved
-40 ° to 70 °C ambient. Derate each output 2.5% per degree from 50 °C to 70 °C.
( -20 °C start up). Meets full spec after 1/2 load. 10 min warm-up
Storage temperature:
-40 °C to 85 °C
Electromagnetic susceptibility:
Designed to meet EN61000-4; -3, -5, -6, -11 Level 3, Level 4 for -2, -4
Humidity:
Operating; non-condensing 10% to 95% RH
Vibration:
MIL-STD-810E
MTBF demonstrated:
> 350,000 hours at full load, one uMP4 case + two modules, Telcordia SR-332
calculated MTBF
Altitude:
Up to 10k feet; derate linear to 50% from 10k-30k feet
Operating temperature:
CB
CE
CCC
【Old Posts】Record Total Posts
First floor for Nong Jie... Just kidding. I have always had obsessive compulsive disorder. For example, when digging graves, I planned to dig them all up one by one from the beginning to the latest. B...
辛昕 Programming Basics
I stayed up late for 3 consecutive nights, but achieved little results.
Look at the picture without explanation...
shower.xu RF/Wirelessly
Introduction to Power Line Network Technology
In the past, there have been many factors that have prevented the popularization of power line technology . The most suspicious one is: Can IP packets really be transmitted on 110V or 220V power lines...
feifei Embedded System
MSP430 (F5529) study notes - UCS configuration details
MSP430 (F5529) is more powerful than MSP430 (F149). UCS Introduction The UCS of MSP430F5XX/MSP430F6XX series devices contains five clock sources, namely: XT1CLK, VLOCLK, REFOCLK, DCOCLK and XT2CLK. Fo...
fish001 Microcontroller MCU
The most comprehensive summary of Beaglebone learning peripheral circuit design reference materials
I have compiled all the reference materials used in the peripheral circuit design process and put them here. Everyone is welcome to download them. There are materials for commercial boards, open sourc...
fengzhang2002 DSP and ARM Processors
Analog electronics knowledge
1. Why are T1 and T2 damaged due to excessive power consumption when D1 is open? 2. Why does T2 get damaged due to excessive power consumption when the collector of T1 is open? Please help me explain ...
whwshiyuan1984 Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1350  2274  2238  2283  2090  28  46  43  44  24 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号