EEWORLDEEWORLDEEWORLD

Part Number

Search

SIT9005ACB1D-18DB

Description
OSC MEMS
CategoryPassive components   
File Size333KB,9 Pages
ManufacturerSiTime
Environmental Compliance
Download Datasheet View All

SIT9005ACB1D-18DB Overview

OSC MEMS

SiT9005
1 to 141 MHz EMI Reduction Oscillator
Features
Applications
Spread spectrum for EMI reduction
Wide spread % option
Center spread: from ±0.125% to ±2%, ±0.125% step size
Down spread: -0.25% to -4% with -0.25% step size
Spread profile option: Triangular, Hershey-kiss
Programmable rise/fall time for EMI reduction: 8 options,
0.25 to 40 ns
Any frequency between 1 MHz and 141 MHz accurate to
6 decimal places
100% pin-to-pin drop-in replacement to quartz-based XO’s
Excellent total frequency stability as low as ±20 ppm
Operating temperature from -40°C to 85°C.
Low power consumption of 4.0 mA typical at 1.8V
Pin1 modes: Standby, output enable, or spread disable
Fast startup time of 5 ms
LVCMOS output
Industry-standard packages
QFN: 2.0 x 1.6, 2.5 x 2.0, 3.2 x 2.5 mm
2
Contact
SiTime
for SOT23-5 (2.9 x 2.8 mm
2
)
RoHS and REACH compliant, Pb-free, Halogen-free
and Antimony-free
Surveillance camera
IP camera
Industrial motors
Flat panels
Multi function printers
PCI express
Electrical Specifications
Table 1. Electrical Characteristics
All Min and Max limits are specified over temperature and rated operating voltage with 15 pF output load unless otherwise stated.
Typical values are at 25°C and 3.3V supply voltage.
Parameters
Output Frequency Range
Symbol
Min.
Typ.
Max.
Unit
Condition
Frequency Range
f
1
141
MHz
Frequency Stability and Aging
Frequency Stability
F_stab
-20
-25
-50
Operating Temperature Range
T_use
-20
-40
Supply Voltage
Vdd
1.62
2.25
2.52
2.7
2.97
2.25
Current Consumption
OE Disable Current
Idd
I_OD
Standby Current
I_std
1.8
2.5
2.8
3.0
3.3
5.6
5.0
5.0
4.6
2.1
0.4
+20
+25
+50
+70
+85
1.98
2.75
3.08
3.3
3.63
3.63
6.5
5.5
6.5
5.2
4.3
1.5
ppm
ppm
ppm
°C
°C
V
V
V
V
V
V
mA
mA
mA
mA
µA
µA
No load condition, f = 40 MHz, Vdd = 2.5V to 3.3V
No load condition, f = 40 MHz, Vdd = 1.8V
f = 40 MHz, Vdd = 2.5V to 3.3V, OE = GND, Output in high-Z
state
f = 40 MHz, Vdd = 1.8V, OE = GND, Output in high-Z state
ST
= GND, Vdd = 2.5V to 3.3V, Output is weakly pulled down
ST
= GND, Vdd = 1.8V, Output is weakly pulled down
Inclusive of initial tolerance at 25°C, 1st year aging at 25°C, and
variations over operating temperature, rated power supply
voltage. Spread = Off.
Operating Temperature Range
Extended Commercial
Industrial
Supply Voltage and Current Consumption
Rev 1.0
September 25, 2017
www.sitime.com
Analysis of transistor voltage stabilization circuit
[i=s]This post was last edited by Beixiao on 2021-11-13 11:39[/i]I used a series voltage regulator circuit before, and then I saw this circuit. Both circuits can stabilize the voltage, but what is the...
悲晓 Analog electronics
Share and summarize the problems in lithium-ion battery production
[i=s]This post was last edited by qwqwqw2088 on 2020-1-24 15:03[/i]30 questions in total 1. Opposites in batteries 2. Analysis of low-capacity ideas 3. A brief discussion of Six Sigma Design 4. Severa...
qwqwqw2088 Analogue and Mixed Signal
An error occurred when writing files under EVC and reading them under vc
Under EVC: typedef struct { TCHAR id1[200]; TCHAR id2[200]; TCHAR id3[200]; TCHAR id4[200]; TCHAR id5[200]; TCHAR id6[200]; TCHAR id7[200]; TCHAR id8 [200]; TCHAR id9[200]; TCHAR id10[200]; }Info; Inf...
梦幻泡影 Embedded System
Why is the output voltage of the power supply I designed almost 0?
In the power design module, I refer to TI's design circuit. The two power chips are of the same model, and the peripheral resistors and capacitors are calculated using the same formula. Why can one ou...
testttest Analogue and Mixed Signal
Ask for help on the program under msp430 simulation
In the past, I always ran it at full speed, waited a few times, and then deleted the red erase. As a result, it was indeed burned in. The question is how did you download it?...
水货老手 Microcontroller MCU
NXP agent: WT Microelectronics or Zhou Ligong, which one is better?
See the attached picture, Wenye and Zhou Ligong are both agents of NXP. May I ask: Which one is better (such as high agent level, adequate technical support, etc.)? Thank you! Description: Automotive ...
yhye2world Automotive Electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 717  1460  1526  2562  2461  15  30  31  52  50 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号