EEWORLDEEWORLDEEWORLD

Part Number

Search

SIT9005ACF1D-33EA

Description
OSC MEMS
CategoryPassive components   
File Size333KB,9 Pages
ManufacturerSiTime
Environmental Compliance
Download Datasheet View All

SIT9005ACF1D-33EA Overview

OSC MEMS

SiT9005
1 to 141 MHz EMI Reduction Oscillator
Features
Applications
Spread spectrum for EMI reduction
Wide spread % option
Center spread: from ±0.125% to ±2%, ±0.125% step size
Down spread: -0.25% to -4% with -0.25% step size
Spread profile option: Triangular, Hershey-kiss
Programmable rise/fall time for EMI reduction: 8 options,
0.25 to 40 ns
Any frequency between 1 MHz and 141 MHz accurate to
6 decimal places
100% pin-to-pin drop-in replacement to quartz-based XO’s
Excellent total frequency stability as low as ±20 ppm
Operating temperature from -40°C to 85°C.
Low power consumption of 4.0 mA typical at 1.8V
Pin1 modes: Standby, output enable, or spread disable
Fast startup time of 5 ms
LVCMOS output
Industry-standard packages
QFN: 2.0 x 1.6, 2.5 x 2.0, 3.2 x 2.5 mm
2
Contact
SiTime
for SOT23-5 (2.9 x 2.8 mm
2
)
RoHS and REACH compliant, Pb-free, Halogen-free
and Antimony-free
Surveillance camera
IP camera
Industrial motors
Flat panels
Multi function printers
PCI express
Electrical Specifications
Table 1. Electrical Characteristics
All Min and Max limits are specified over temperature and rated operating voltage with 15 pF output load unless otherwise stated.
Typical values are at 25°C and 3.3V supply voltage.
Parameters
Output Frequency Range
Symbol
Min.
Typ.
Max.
Unit
Condition
Frequency Range
f
1
141
MHz
Frequency Stability and Aging
Frequency Stability
F_stab
-20
-25
-50
Operating Temperature Range
T_use
-20
-40
Supply Voltage
Vdd
1.62
2.25
2.52
2.7
2.97
2.25
Current Consumption
OE Disable Current
Idd
I_OD
Standby Current
I_std
1.8
2.5
2.8
3.0
3.3
5.6
5.0
5.0
4.6
2.1
0.4
+20
+25
+50
+70
+85
1.98
2.75
3.08
3.3
3.63
3.63
6.5
5.5
6.5
5.2
4.3
1.5
ppm
ppm
ppm
°C
°C
V
V
V
V
V
V
mA
mA
mA
mA
µA
µA
No load condition, f = 40 MHz, Vdd = 2.5V to 3.3V
No load condition, f = 40 MHz, Vdd = 1.8V
f = 40 MHz, Vdd = 2.5V to 3.3V, OE = GND, Output in high-Z
state
f = 40 MHz, Vdd = 1.8V, OE = GND, Output in high-Z state
ST
= GND, Vdd = 2.5V to 3.3V, Output is weakly pulled down
ST
= GND, Vdd = 1.8V, Output is weakly pulled down
Inclusive of initial tolerance at 25°C, 1st year aging at 25°C, and
variations over operating temperature, rated power supply
voltage. Spread = Off.
Operating Temperature Range
Extended Commercial
Industrial
Supply Voltage and Current Consumption
Rev 1.0
September 25, 2017
www.sitime.com
Found a good way to disassemble LQFP...
Last time a friend asked me how to disassemble LQFP, and after much discussion, we found that it is really difficult to do without a heat gun... Or two people would have to use four soldering irons to...
anqi90 DIY/Open Source Hardware
Experts please come in!!! Dual power supply working, when the main power supply is disconnected, the backup power supply works?
[i=s]This post was last edited by paulhyde on 2014-9-15 03:32[/i]:) I've been busy with dual power supplies recently, but I'm a little confused. For example, for a laptop, when the computer is fully c...
lin861296825 Electronics Design Contest
Problem starting wince from eboot?
After starting EBOOT, press L to start wince normally. The serial port output is as follows: Microsoft Windows CE Ethernet Bootloader Common Library Version 1.0 Built Mar 13 2003 23:08:10 Microsoft Wi...
5133858 Embedded System
Allegro sets groups to be equal in length
When using Allegro to set the SRAM group to be equal in length, the following problem occurs: PinPair creation fails. How can I solve this problem?...
dongsy2012 PCB Design
Analyze the relationship between J-link hardware, firmware, and drivers
J-Link is a commonly used ARM debugger in the field of embedded development. Beginners are not very clear about the relationship between J-Link hardware version, J-Link driver and J-Link firmware. Her...
MamoYU MCU
Football robot graduation project, please help me
Requirements: 1. Realize the mechanism design and circuit design of the soccer robot body ; 2. Complete the wireless communication control between the soccer robot and the monitoring computer; 3. Use ...
mirasy Robotics Development

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1959  2561  1239  2095  2361  40  52  25  43  48 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号