EEWORLDEEWORLDEEWORLD

Part Number

Search

3C92CTX

Description
OPTOISOLATOR 1KV TRANS TO72-4
CategoryLED optoelectronic/LED   
File Size1MB,17 Pages
ManufacturerTT Electronics
Download Datasheet Parametric View All

3C92CTX Online Shopping

Suppliers Part Number Price MOQ In stock  
3C92CTX - - View Buy Now

3C92CTX Overview

OPTOISOLATOR 1KV TRANS TO72-4

3C92CTX Parametric

Parameter NameAttribute value
Number of channels1
Voltage - Isolation1000VDC
Current transfer ratio (minimum value)30% @ 10mA
Current transfer ratio (maximum)200% @ 10mA
Open/close time (typ.)9µs, 6µs (maximum)
Rise/Fall Time (Typical)-
input typeDC
Output typetransistor
Voltage - Output (maximum)50V
Current - Output/Channel30mA
Voltage - Forward (Vf) (Typical)1.2V (maximum)
Current - DC Forward (If)50mA
Vce saturation value (maximum value)400mV
Operating temperature-55°C ~ 125°C
Installation typeThrough hole
Package/casingTO-206AF, TO-72-4 metal can
Supplier device packagingTO-72-4
OPIA814, OPIA815, OPIA817
OPIA1210, OPIA4010
DIP Package
Features:
5,000 Vrms electrical isolation
Choice of a Single and Dual LED
Phototransistor or Photodarlington Sensor
Low-cost plastic Dual-In-Line (DIP) package
UL Certification No: E58730
VDE No
:
40026625 40026536, 40026654
Approval Agency:
Description:
The OPIA series optocouplers are designed for applications that use an analog output (Phototransistor or
Photodarlington) in a dual-in-line package. A wide selection of configurations are available. With typical isolation
voltage of 5,000 Volts(RMS), these products meet typical power system isolation requirements.
Theory of operation: The LED transmitter is used to illuminate the Photosensor providing electrical isolation
between two power systems while maintaining the ability to transmit information from one power system to the
other. In many applications, analog signal levels may be required to be transmitted between two power systems
while maintaining isolation between the power systems up to 5,000 volts(RMS). A variety of LED and photosensor
configurations are available depending on the system requirements.
The ratio Current Transfer Ratio (CTR) is determined by using the output current and input current for analog
photosensors. CTR ratios can range from as low as 5 to over 9,000 depending on the device.
CTR
=
Photosenso
r
Current
LED
Current
=
20
mA
* 100
=
200
10
mA
All DIP product is shipped in a shipping tube with “TU” identified on the end of the part number.
Example: OPIA817DTUE is a 4-Pin DIP shipped in a tube (TU).
Applications:
High voltage isolation: 5,000 Volts RMS
PCBoard power system isolation
Industrial equipment power isolation
Medical equipment power isolation
Office equipment
RoHS
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
Issue A.5
8/09
Page 1 of 17
OPTEK Technology Inc. —
1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
See how many layers ARM has reached? Ten layers in total
I like embedded systems more, but I don't work in this field. I can only learn by myself (protocol stack) as a hobby. Now I am familiar with UCOS2 system, can read source code, and understand task mec...
sz_jian ARM Technology
Can any expert help me find what is wrong? The DMA channel transfer is completed, and there is data in DR but it is not written to the array hh
[code]UART3Init(); RS485_SendByte(0x00); Delay2(10); hh[0]=0x66; MYDMA_Config(DMA1_Channel3,(u32)&USART3->DR,(u32)hh,1);//DMA1 channel 3, peripheral is serial port 3, memory is hh, length 1 USART3->CR...
mynameisbill2 stm32/stm8
How to export data in Keil uvision?
I would like to ask for help from all the experts. I am recently debugging a board and need to export the data of an array of 1000 in the program. However, I have searched for a long time and cannot f...
fridaydpd MCU
I read the forum posts. Has anyone used 900MHz Zigbee chips? What are the results?
The ism frequency band in Europe and North America is mainly 900M. I wonder if anyone has considered or made a 900 zigbee module? Please introduce it....
joooker RF/Wirelessly
[Transfer] ESP8266 Guide: Role, Functions and Applications
Original title: ESP8266 Guide: Role, Function and Development Approach [url]http://makerpro.cc/2015/08/esp8266-guideline/[/url] [p=26, null, left][color=rgb(51 , 51, 51)][font=Raleway, Arial, sans-ser...
dontium RF/Wirelessly
【Let's play MicroPython】Belated unboxing
This is my first post on ee. I hope to share and learn with you~ I received the express delivery on the weekend. During that time, the forum left my phone number wrong. This incident made me meet the ...
荣丰宇 MicroPython Open Source section

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1156  65  170  215  1752  24  2  4  5  36 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号