EEWORLDEEWORLDEEWORLD

Part Number

Search

SIT8208AI-31-25E-10.000000Y

Description
-40 TO 85C, 5032, 20PPM, 2.5V, 1
CategoryPassive components   
File Size750KB,15 Pages
ManufacturerSiTime
Environmental Compliance
Download Datasheet View All

SIT8208AI-31-25E-10.000000Y Overview

-40 TO 85C, 5032, 20PPM, 2.5V, 1

SiT8208
Ultra Performance Oscillator
The Smart Timing Choice
The Smart Timing Choice
Features
Applications
Any frequency between 1 and 80 MHz accurate to 6 decimal places
100% pin-to-pin drop-in replacement to quartz-based oscillators
Ultra low phase jitter: 0.5 ps (12 kHz to 20 MHz)
Frequency stability as low as ±10 PPM
Industrial or extended commercial temperature range
LVCMOS/LVTTL compatible output
Standard 4-pin packages: 2.5 x 2.0, 3.2 x 2.5, 5.0 x 3.2,
7.0 x 5.0 mm x mm
Instant samples with
Time Machine II
and
field programmable
oscillators
Outstanding silicon reliability of 2 FIT or 500 million hour MTBF
Pb-free, RoHS and REACH compliant
Ultra short lead time
SATA, SAS, Ethernet, PCI Express, video, WiFi
Computing, storage, networking, telecom, industrial control
Electrical Characteristics
[1]
Parameter
Output Frequency Range
Frequency Stability
Symbol
f
F_stab
Min.
1
-10
-20
-25
-50
First year Aging
10-year Aging
Operating Temperature Range
T_use
F_aging
-1.5
-5
-20
-40
Supply Voltage
Vdd
1.71
2.25
2.52
2.97
Current Consumption
OE Disable Current
Idd
I_OD
Standby Current
I_std
Duty Cycle
Rise/Fall Time
Output Voltage High
Output Voltage Low
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
DC
Tr, Tf
VOH
VOL
VIH
VIL
Z_in
45
90%
70%
2
Typ.
1.8
2.5
2.8
3.3
31
29
1.2
100
Max.
80
+10
+20
+25
+50
+1.5
+5
+70
+85
1.89
2.75
3.08
3.63
33
31
31
30
70
10
55
2
10%
30%
250
Unit
MHz
PPM
PPM
PPM
PPM
PPM
PPM
°C
°C
V
V
V
V
mA
mA
mA
mA
A
A
%
ns
Vdd
Vdd
Vdd
Vdd
kΩ
MΩ
15 pF load, 10% - 90% Vdd
IOH = -6 mA, IOL = 6 mA, (Vdd = 3.3V, 2.8V, 2.5V)
IOH = -3 mA, IOL = 3 mA, (Vdd = 1.8V)
No load condition, f = 20 MHz, Vdd = 2.5V, 2.8V or 3.3V
No load condition, f = 20 MHz, Vdd = 1.8V
Vdd = 2.5V, 2.8V or 3.3V, OE = GND, output is Weakly Pulled
Down
Vdd = 1.8 V. OE = GND, output is Weakly Pulled Down
Vdd = 2.5V, 2.8V or 3.3V, ST = GND, output is Weakly Pulled
Down
Vdd = 1.8 V. ST = GND, output is Weakly Pulled Down
25°C
25°C
Extended Commercial
Industrial
Supply voltages between 2.5V and 3.3V can be supported.
Contact
SiTime
for additional information.
Inclusive of Initial tolerance at 25 °C, and variations over
operating temperature, rated power supply voltage and load
Condition
Frequency Range
Frequency Stability and Aging
Operating Temperature Range
Supply Voltage and Current Consumption
LVCMOS Output Characteristics
Input Characteristics
Pin 1, OE or ST
Pin 1, OE or ST
Pin 1, OE logic high or logic low, or ST logic high
Pin 1, ST logic low
Note:
1. All electrical specifications in the above table are specified with 15 pF output load and for all Vdd(s) unless otherwise stated.
SiTime Corporation
Rev. 1.02
990 Almanor Avenue
Sunnyvale, CA 94085
(408) 328-4400
www.sitime.com
Revised June 24, 2013
Electronic motherboard cable we repair?
Electronic motherboard cable we repair?...
一梦千回 RF/Wirelessly
The easiest question is how to control the LED on the evaluation board under VxWorks?
VxWorks + ARM7 4510 evaluation board, an LED flashing program that has passed bare metal programming debugging under ADS. After adding it to a program that can already run under VxWorks. (Of course, t...
armchina Real-time operating system RTOS
microPython cannot import .py file
As shown in the figure, after the pyboardv202 is burned with microPython firmware, main.py cannot be imported and the terminal software cannot send commands...
lehuijie MicroPython Open Source section
CC2650 uses TI's mobile app to flash the firmware to Zigbee, how to flash it back to Bluetooth?
After flashing the Zigbee firmware, the phone can no longer find the CC2650. Can I only use a programmer to flash it back to Bluetooth mode? Can I flash it with a JLink?...
szqt Wireless Connectivity
Make a multi-way switching power supply, please provide a solution
To make an output of positive and negative 200V, current 100MA, dual 15V, 200MA, which circuit should be used for the pre-stage...
dianzijie5 Power technology
AT89S51 MCU Experiment and Practice Tutorial (very good introductory material)
Very good information for getting started with microcontrollers, including: 1. Detailed schematic module introduction; 2. Program flow chart; 3. Assembly language implementation; 4. C implementation; ...
hxqhit 51mcu

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1600  8  1688  2241  1976  33  1  34  46  40 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号