EEWORLDEEWORLDEEWORLD

Part Number

Search

KNP400JT-73-6R8

Description
RES WW 4W 5% AXIAL
CategoryPassive components   
File Size269KB,3 Pages
ManufacturerYAGEO
Websitehttp://www.yageo.com/
Environmental Compliance
Download Datasheet Parametric View All

KNP400JT-73-6R8 Overview

RES WW 4W 5% AXIAL

KNP400JT-73-6R8 Parametric

Parameter NameAttribute value
resistance6.8 Ohms
Tolerance±5%
Power (W)4W
componentWinding
characteristicFlame retardant coating, safe
Temperature Coefficient±300ppm/°C
Operating temperature-40°C ~ 200°C
Package/casingAxial
Supplier device packagingAxial
size/dimensions0.256" diameter x 0.689" length (6.50mm x 17.50mm)
Height - Installation (maximum)-
Number of terminals2
Through-hole resisTors
Wirewound Resistors
General Type
Normal & Miniature Style [ KNP Series ]
FeATures
Power Rating
Resistance Tolerance
T.C.R.
Flameproof Multi-layer Coating Meets
Flameproof Feature Meets Overload Test
1/4W, 1/2W, 1W, 2W, 3W, 4W, 5W, 7W
±1%, ±5%
±300ppm/°C
UL-94V-0
UL-1412
iNTroDuCTioN
The resistor element is a resistive wire which
is wound in a single layer on a ceramic rod,
with tinned connecting wires of electrolytic
copper welded to the end-caps. The ends of
the resistive wire are connected to the caps by
welding. The resistors are coated with layers of
green color flame-proof lacquer.
DerATiNg CurVe
For resistors operated in ambient temperatures above 40°C, power rating must be derated
in accordance with the curve below.
Rated Load (%)
40 70
100
80
60
40
20
50
100 150 200 250 300
3W-7W
1/4W-3WS
200
275 °C
Ambient Temperature (°C)
DiMeNsioNs
sTYle
Normal
KNP-25
KNP-50
KNP100
ød
H
L
øD
KNP200
KNP300
KNP400
KNP500
KNP600
KNP700
Note: KNP1WS ( for MB Type ) ød = 0.8±0.05 mm
Unit: mm
DiMeNsioN
Miniature
KNP50S
KNP1WS
KNP2WS
KNP3SS
KNP3WS
KNP5WS
l
6.3±0.5
9.0±0.5
11.5±1.0
15.5±1.0
17.5±1.0
øD
2.5±0.3
3.5±0.3
4.6±0.5
5.2±0.5
6.5±0.5
h
28±2.0
26±2.0
35±2.0
33±2.0
32±2.0
ød
0.55±0.05
0.55±0.05
0.8±0.05
0.8±0.05
0.8±0.05
KNP7WS
-
24.5±1.0
24.5±1.0
8.5±0.5
8.5±0.5
38±2.0
38±2.0
0.8±0.05
0.8±0.05
Several different ways to describe triggers in Verilog language
There are several different ways to describe triggers in Verilog. Some are synthesizable, and some are not synthesizable and are used in the testbench. The first description is the most common and can...
eeleader FPGA/CPLD
Solutions to monitoring system failures
1. Equipment failure caused by incorrect power supply. There are several possible reasons for incorrect power supply: incorrect power supply line or power supply voltage, insufficient power, short cir...
lukdtc Test/Measurement
'l;'
hahaha...
handsomeboy Embedded System
Stepper motor knowledge
A stepper motor is an actuator that converts electrical pulses into angular displacement. When the stepper driver receives a pulse signal, it drives the stepper motor to rotate a fixed angle (called t...
jek9528 Industrial Control Electronics
I need help with the capacitive touch button problem of MSP430F5 microcontroller.
Whenever the MCU runs to TI_CAPT_Init_Baseline(&slider); //capacitive touch initialization thing will jump to this void TI_CTS_fRO_COMPB_TA1_SW_HAL(const struct Sensor *group,uint16_t *counts) { uint8...
xiexfei Microcontroller MCU
Solve FPGA chip programming questions
Every time I finish burning the program into the FPGA, the result is displayed, but after pressing reset or power off, the result is the same as before the program was burned. Later I found that my pr...
wall_e FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1548  1363  1834  1496  1210  32  28  37  31  25 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号