EEWORLDEEWORLDEEWORLD

Part Number

Search

CPCC052R700KE66

Description
RES 2.7 OHM 5W 10% RADIAL
CategoryPassive components   
File Size84KB,3 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Environmental Compliance
Download Datasheet Parametric View All

CPCC052R700KE66 Overview

RES 2.7 OHM 5W 10% RADIAL

CPCC052R700KE66 Parametric

Parameter NameAttribute value
resistance2.7 Ohms
Tolerance±10%
Power (W)5W
componentWinding
characteristicFlame resistant and safe
Temperature Coefficient±400ppm/°C
Operating temperature-65°C ~ 275°C
Package/casingRadial
Supplier device packagingRadial leads
size/dimensions0.512" long x 0.354" wide (13.00mm x 9.00mm)
Height - Installation (maximum)1.003"(25.48mm)
Number of terminals2
failure rate-
CPCC, CPCF High Volume
www.vishay.com
Vishay Dale
Wirewound/Metal Oxide Resistors, Commercial Power,
Vertical Mount
FEATURES
• Space saving
• Direct mounting on printed circuit board
• High power to size ratio
• Special cement potting compound and ceramic
case provide high thermal conductivity in a
fireproof package
• Material categorization:
for definitions of compliance please see
www.vishay.com/doc?99912
STANDARD ELECTRICAL SPECIFICATIONS
GLOBAL MODEL
CPCC02
CPCF02
CPCC03
CPCF03
CPCC05
CPCF05
CPCC07
CPCF07
CPCC10
CPCC1A
POWER RATING
P
40 °C
W
2
2
3
3
5
5
7
7
10
10
RESISTANCE RANGE RESISTANCE RANGE
WIREWOUND
METAL OXIDE
0.1 to 100
NA
0.1 to 100
NA
0.1 to 100
NA
0.1 to 100
NA
0.1 to 100
0.1 to 100
n/a
101 to 50K
n/a
101 to 50K
n/a
101 to 50K
n/a
101 to 50K
n/a
n/a
TOLERANCE
±%
5, 10
5, 10
5, 10
5, 10
5, 10
5, 10
5, 10
5, 10
5, 10
5, 10
WEIGHT
(typical)
g
4.7
4.7
5.5
5.5
6.9
6.9
9.2
9.2
14.3
13.2
TECHNICAL SPECIFICATIONS
PARAMETER
Temperature Coefficient
Short Time Overload
Maximum Working Voltage
Operating Temperature Range
Terminal Strength
Dielectric Withstanding Voltage
UNIT
ppm/°C
-
V
°C
lb
V
AC
CPCC, CPCF HIGH VOLUME RESISTOR CHARACTERISTICS
± 400
5 x rated power for 5 s
(P x R)
1/2
-65 to +275 for wirewound, -65 to +225 for metal oxide
10 minimum
1000
GLOBAL PART NUMBER INFORMATION
Global Part Numbering example: CPCC0515R00JE66
C
P
C
C
0
VALUE
5
1
5
R
0
0
J
E
6
6
SPECIAL
(Dash number)
(up to 3 digits)
From
1 to 999
as applicable
GLOBAL MODEL
(See Standard Electrical
Specifications Global
Model column for
options)
TOLERANCE
J
= ± 5.0 %
K
= ± 10.0 %
PACKAGING
E66
= lead (Pb)-free bulk pack
R
= decimal
K
= thousand
R1500
= 0.15
1K500
= 1500
Revision: 02-Oct-15
Document Number: 30116
1
For technical questions, contact:
ww2aresistors@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
  Advanced control software and DCS human-machine interface design
Starting from the actual application of advanced control software, this paper explains how to solve the design problem of the operation interface between advanced control software and DCS. Since advan...
frozenviolet Industrial Control Electronics
SPI data transmission problem in STM32
I connected an ADC-TLC2543 to the outside of STM32, and used the SPI of STM32 to transmit the result after ADC conversion. Now I use an oscilloscope to observe the output of MOSI (PA7) in STM32, and t...
向日葵不哭100 stm32/stm8
Regarding the problem of digital-to-analog-to-analog conversion? Maybe I don't understand the microcontroller deeply enough, can anyone answer this question?
For example, when using a single-chip microcomputer, I directly set the high level to light up the external light-emitting diode, and I use digital-to-analog conversion to output a voltage to light up...
落日归侠 51mcu
Are there any requirements for the PWM amplitude?
I want to use pt4207 to make a PWM dimming circuit for LEDs. What are the requirements for the PWM signal amplitude of pin 1 of pt4207? Can 0~5V be used? Also, how should pin 1 be connected?...
linkin19 LED Zone
CPLD chip reset pin
Which one is the reset pin in the picture below? Thanks!...
shaorc Power technology
LM3S811's 24L01 sends
[local]1[Using 24L01 to do wireless transmission experiment, but when transmitting, it is always unable to send normally, TX_Sta=SPI_Read(STATUS); the read TX_Sta is always 0; I have posted the source...
guozhiyang Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2235  224  49  1445  1051  46  5  1  30  22 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号