EEWORLDEEWORLDEEWORLD

Part Number

Search

DCD290P138T600A40

Description
EVAL BRD FOR DCM290P138T600A40
CategoryDevelopment board/suite/development tools   
File Size654KB,17 Pages
ManufacturerVICOR
Websitehttp://www.vicorpower.com/
Environmental Compliance
Download Datasheet Parametric View All

DCD290P138T600A40 Online Shopping

Suppliers Part Number Price MOQ In stock  
DCD290P138T600A40 - - View Buy Now

DCD290P138T600A40 Overview

EVAL BRD FOR DCM290P138T600A40

DCD290P138T600A40 Parametric

Parameter NameAttribute value
The main purposeDC/DC, step down
Output and type1. Isolation
Power - output600W
Voltage - Output13.8V
Current - Output43.5A
Voltage - input160 V ~ 420 V
Regulator topologystep down
Frequency - Switch-
Board typecompletely filled
What's includedplate
IC/parts usedDCM290P138T600A40
USER GUIDE | UG:017
Analog Control 3623 and 4623 ChiP DCMs
Evaluation Board
Arthur Russell
VI Chip
®
Applications Engineering
October 2014
Contents
Introduction
Contents
Features
Board Description
General Components
Test Points Description
Page
1
3
3
4
4
6
Introduction
The Analog Control 3623 and 4623 ChiP DCM evaluation boards described in this document are
designed to be used with the DCM family of isolated, DC-DC converters. The 3623 DCM board is used
for the analog control, low input voltage 3623 ChiP products, while the 4623 DCM board is used for
the analog control, high input voltage (offline) 4623 ChiP products.
The DCM evaluation board can be configured for various enabling and fault monitoring schemes,
as well as to exercise various modes of trimming, depending on the application requirements. The
evaluation board can be used to evaluate DCMs in either a stand-alone configuration, or as an
array of modules.
Schematic, Assembly Drawing
and Bill of Materials
7
Recommended Test
Equipment
Basic Connections
Board Operation Details
Trim Control
Fault Monitoring
Chassis Ground
Paralleling
14
14
14
15
15
16
16
Enable options:
1.
2.
On-board mechanical switch (default)
External control
Trim options:
1.
2.
3.
Fixed trim operation (default): the TR pin is permitted to float at initial startup.
The DCM disables output trimming and the output trim is programmed to the nominal rated V
OUT
.
Variable trim operation, on-board variable resistor: The trim pin voltage is ratiometric,
with a rheostat working against a pull-up resistor inside the DCM to VCC.
Variable trim operation, off-board control: The trim pin voltage is controlled via external
programming control, which is referenced to the –IN of each specific DCM in the system.
Fault monitor options:
1.
2.
On-board LED: the FT pin drives a visible LED for visual feedback on fault status.
On-board optocoupler: the FT pin drives an on-board optocoupler to bring
fault status across the primary-secondary isolation boundary.
UG:017
vicorpower.com
Applications Engineering: 800 927.9474
Page 1
What is the difference between simulation and burning operation?
[i=s] This post was last edited by dontium on 2015-1-23 13:07 [/i] Please analyze:What is the difference between using a development board to simulate (external DRAM memory) and burning the program di...
lwh1987927 Analogue and Mixed Signal
About PWM A/d GPIO driver
Is it feasible to use address mapping? Or is it better to write a driver?...
sanoboy Embedded System
TCP/IP Detailed Explanation (Layer 7/Layer 4 Protocol)
Why is there TCP/IP protocol?All over the world, various computers run different operating systems to serve everyone. The methods used by these computers to express the same information vary greatly. ...
Aguilera RF/Wirelessly
Analog Devices' Lithium Battery Management Solutions for HEVs and EVs
Due to the excellent energy and power characteristics of lithium batteries in hybrid and pure electric vehicles, the automotive industry has begun to shift from nickel-metal hydride batteries to lithi...
EEWORLD社区 ADI Reference Circuit
[Ask] When using 16554 to expand the serial port, port a is normal, but port b always overflows when receiving.
I use 16554 to expand 4 serial ports. When I test port a and port b at the same time, port a works fine, but port b often overflows. As a result, the interrupt pin is always pulled high, making it imp...
demoxie Embedded System
Application of LOGO! Control in Pressure Tank Control System
LOGO! is a universal logic module . This product integrates control, operation and display functions. Various basic LOGO! and expansion module combinations can accurately adapt to specific tasks. The ...
frozenviolet Industrial Control Electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 936  290  2421  379  387  19  6  49  8  29 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号