100% pin-to-pin drop-in replacement to quartz-based (VC)TCXO
Frequency stability as low as ±5 ppm. Contact SiTime for tighter
stability options
Low phase jitter: 0.5 ps (12 kHz to 20 MHz)
LVCMOS compatible output with SoftEdge
™
option for EMI reduction
Voltage control, standby, output enable or no connect modes
Standard 4-pin packages: 2.5 x 2.0, 3.2 x 2.5, 5.0 x 3.2, 7.0 x 5.0 mm
Outstanding silicon reliability of 2 FIT, 10 times better than quartz
Pb-free, RoHs and REACH compliant
WiFi, 3G, LTE, SDI, Ethernet, SONET, DSL
Telecom, networking, smart meter, wireless, test instrumentation
Electrical Characteristics
Parameter
Output Frequency Range
Initial Tolerance
Stability Over Temperature
Symbol
f
F_init
F_stab
Min.
-1.5
-5
Typ.
–
–
Max.
+1.5
+5
Unit
MHz
ppm
ppm
At 25°C after two reflows
Over operating temperature range at rated nominal power
supply voltage and load. (see
ordering codes on page 6)
Contact SiTime for tighter stability options.
Supply Voltage
Output Load
First year Aging
10-year Aging
Operating Temperature Range
Supply Voltage
T_use
Vdd
F_vdd
F_load
F_aging
–
–
-2.5
-4.0
-20
-40
1.71
2.25
2.52
2.70
2.97
Pull Range
Upper Control Voltage
Control Voltage Range
Control Voltage Input Impedance
Frequency Change Polarity
Control Voltage -3dB Bandwidth
Current Consumption
OE Disable Current
PR
VC_U
VC_L
Z_vc
–
V_BW
Idd
I_OD
–
–
–
–
–
Standby Current
Duty Cycle
LVCMOS Rise/Fall Time
SoftEdge™ Rise/Fall Time
Output Voltage High
Output Voltage Low
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
VOH
VOL
VIH
VIL
Z_in
I_std
DC
Tr, Tf
–
–
45
–
Vdd-0.1
–
100
50
0.1
–
–
–
–
1.8
2.5
2.8
3.0
3.3
±12.5
–
–
–
Positive slope
–
31
29
–
–
–
–
–
1.5
8
33
31
31
30
70
10
55
2
–
0.1
–
–
–
+2.5
+4.0
+70
+85
1.89
2.75
3.08
3.3
3.63
ppb
ppm
ppm
ppm
°C
°C
V
V
V
V
V
ppm
V
V
k
–
kHz
mA
mA
mA
mA
µA
µA
%
ns
ns
Vdd
Vdd
Vdd
Vdd
k
No load condition, f = 20 MHz, Vdd = 2.5V, 2.8V or 3.3V.
No load condition, f = 20 MHz, Vdd = 1.8V.
Vdd = 2.5V, 2.8V or 3.3V, OE = GND, output is Weakly Pulled
Down
Vdd = 1.8 V. OE = GND, output is Weakly Pulled Down
Vdd = 2.5V, 2.8V or 3.3V, ST = GND, output is Weakly Pulled Down.
Condition
27 standard frequencies between 10 MHz and 40 MHz
Refer to the frequency list (page
6)
±10% Vdd (±5% for Vdd = 1.8V)
15 pF ±10% of load
25°C
25°C
Extended Commercial
Industrial
Contact SiTime for any other supply voltage options.
All Vdds. Voltage at which maximum deviation is guaranteed.
Vdd = 1.8V. ST = GND, output is Weakly Pulled Down.
All Vdds
LVCMOS option. Default rise/fall time, All Vdds, 10% - 90% Vdd.
SoftEdge™ option. Frequency and supply voltage dependent.
OH = -7 mA, IOL = 7 mA, (Vdd = 3.3V, 3.0V)
IOH = -4 mA, IOL = 4 mA, (Vdd = 2.8V, 2.5V)
IOH = -2 mA, IOL = 2 mA, (Vdd = 1.8V)
Pin 1, OE or ST
Pin 1, OE or ST
SoftEdge™ Rise/Fall Time Table
90%
–
70%
–
–
–
–
–
–
100
–
10%
–
30%
250
SiTime Corporation
Rev. 1.0
990 Almanor Avenue
Sunnyvale, CA 94085
(408) 328-4400
www.sitime.com
Revised November 12, 2015
SiT5000
Standard Frequency MEMS (VC)TCXO
The Smart Timing Choice
The Smart Timing Choice
Electrical Characteristics (continued)
Parameter
Startup Time
OE Enable/Disable Time
Resume Time
RMS Period Jitter
RMS Phase Jitter (random)
Symbol
T_start
T_oe
T_resume
T_jitt
T_phj
Min.
–
–
–
–
–
–
Typ.
–
–
6
1.7
1.7
0.5
Max.
10
150
10
2
2
1
Unit
ms
ns
ms
ps
ps
ps
Condition
Measured from the time Vdd reaches its rated minimum value
f = 80 MHz. For other frequencies, T_oe = 100 ns + 3 cycles
Measured from the time ST pin crosses 50% threshold
f = 10 MHz, Vdd = 2.5V, 2.8V or 3.3V
f = 10 MHz, Vdd = 1.8V
f = 10 MHz, Integration bandwidth = 12 kHz to 20 MHz, All Vdds
Note:
1. All electrical specifications in the above table are measured with 15pF output load, Contact SiTime for higher drive options.
Pin Configuration
Pin
Symbol
V control
Output
Enable
1
VC/OE/ST/NC
Standby
NC
2
3
4
GND
CLK
VDD
Power
Output
Power
Voltage control
H or Open
[2]
: specified frequency output
L: output is high impedance. Only output driver is disabled.
H or Open
[2]
: specified frequency output
L: output is low (weak pull down). Device goes to sleep mode. Supply
current reduces to I_std.
No connect (input receiver off)
Electrical and case ground
Oscillator output
Power supply voltage
GND
2
3
Functionality
Top View
VC/OE/ST
1
4
VDD
OUT
Note:
2. A pull-up resistor of <10 k? between OE/ ST pin and Vdd is recommended in high noise environment when the device operates in OE/ST mode.
Absolute Maximum
Attempted operation outside the absolute maximum ratings of the part may cause permanent damage to the part. Actual perfor-
mance of the IC is only guaranteed within the operational specifications, not at absolute maximum ratings.
Parameter
Storage Temperature
VDD
Electrostatic Discharge
Soldering Temperature (follow standard Pb free soldering guidelines)
Min.
-65
-0.5
–
–
Max.
150
4
2000
260
Unit
°C
V
V
°C
Thermal Consideration
Package
7050
5032
3225
2520
JA, 4 Layer Board
(°C/W)
191
97
109
117
JA, 2 Layer Board
(°C/W)
263
199
212
222
JC, Bottom
(°C/W)
27
24
27
26
Environmental Compliance
Parameter
Mechanical Shock
Mechanical Vibration
Temperature Cycle
Solderability
Moisture Sensitivity Level
Condition/Test Method
MIL-STD-883F, Method 2002
MIL-STD-883F, Method 2007
JESD22, Method A104
MIL-STD-883F, Method 2003
MSL1 @ 260°C
Rev. 1.0
Page 2 of 7
www.sitime.com
SiT5000
Standard Frequency MEMS (VC)TCXO
The Smart Timing Choice
The Smart Timing Choice
Timing Diagram
90% Vdd, 2.5/2,8/3.3V devices
Vdd
95% Vdd, 1.8V devices
Vdd
Pin 4 Voltage
50% Vdd
T_resume
CLK Output
CLK Output
ST Voltage
T_start
T_start: Time to start from power-off
T_resume: Time to resume from ST
(ST/OE Mode)
(ST Mode Only)
Phase Noise Plot
Phase Noise, 10M Hz carrier, 3.3V, LVCM O S output, TCXO
-100
-110
-120
-130
-140
-150
-160
-170
3
10
Integrated random phase jitter (RM S, 12kHz-5M Hz): 0.52ps
Phase Noise (dBc/Hz)
10
4
10
Frequency O ffset (Hz)
5
10
6
Rev. 1.0
Page 3 of 7
www.sitime.com
SiT5000
Standard Frequency MEMS (VC)TCXO
The Smart Timing Choice
The Smart Timing Choice
SoftEdge™ Option
The SoftEdge™ output is available as a standard option for the SiT500x family of MEMS (VC)TCXOs. It is typically used for EMI
reduction similar to that of the clipped sinewave output common to many quartz based TCXOs.
In the SoftEdge™ mode, the slower rise/fall edges of the output waveform reduce the higher clock harmonics in a digital clock
signal, minimizing EMI radiation at these harmonics. The table below show the actual rise/fall time in relation to the desired output
frequency and the supply voltage with a 10 k / 10 pF load. Rail-to-rail swing of the output is maintained for these supported
frequencies.
Rise/Fall Time for SoftEdge™ Option
Parameter
Rise/Fall Time
Symbol
Tr, Tf
Min.
4.0
2.5
1.5
1.5
Typ.
6.5
4.0
3.5
2.5
Max.
9.5
6.0
5.0
4.5
Unit
ns
ns
ns
ns
Condition
1-26 MHz, 1.8V, 3.0 and 3.3V, MHz 10k and 10 pF, 20%-80% Vd
1-26 MHz, 2.5V and 2.8V, MHz 10k and 10 pF, 20%-80% Vdd
26-40 MHz, 1.8V, 3.0V and 3.3V, MHz 10k and 10 pF, 20%-80% Vdd
26-40 MHz, 2.5V and 2.8V, MHz 10k and 10 pF, 20%-80% Vdd
SoftEdge™ Waveform Examples and Corresponding Harmonics Reduction
Figures below illustrate the harmonic power reduction as the rise/fall times are slowed from the standard squarewave output to
that of the SoftEdge™ output. In general, the 1.8V device shows the lowest harmonics and provides best EMI performance
comparing to devices with higher operating voltages.
LVCMOS and SoftEdge™ Outputs,
VDD = 3.3V
SoftEdge
LVCMOS
3.5
20
Odd Harmonic Power Comparison for LVCMOS and SoftEdge™ Outputs,
VDD = 3.3V
SoftEdge
LVCMOS
3
10
Harmonic Power (dbm)
2.5
0
-10dBm
Amplitude (V)
2
-10
1.5
-20
1
-24.4dbm
-30
0.5
0
-40
0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
0
2
4
6
8
10
12
14
16
18
20
Time (ns)
Harmonic Number
LVCMOS and SoftEdge Outputs,
VDD = 2.5V
SoftEdge
LVCMOS
20
Odd Harmonic Power Comparison for LVCMOS and SoftEdge Outputs,
VDD = 2.5V
SoftEdge
LVCMOS
10
Harmonic Power (dbm)
Amplitude( 0.5V/Div)
0
-11 dBm
-10
-20
-20 dBm
-30
-40
Time (20 ns/Div)
0
2
4
6
8
10
12
14
16
18
20
Harmonic Number
LVCMOS and SoftEdge Outputs,
VDD = 1.8V
SoftEdge
LVCMOS
20
Odd Harmonic Power Comparison for LVCMOS and SoftEdge Outputs,
VDD = 1.8V
SoftEdge
LVCMOS
10
Harmonic Power (dbm)
0
Amplitude ( 0.5V/Div )
-10
-17 dBm
-20
-22
dBm
-30
-40
0
2
4
6
8
10
12
14
16
18
20
Time ( 20ns/Div )
Harmonic Number
Rev. 1.0
Page 4 of 7
www.sitime.com
SiT5000
Standard Frequency MEMS (VC)TCXO
The Smart Timing Choice
The Smart Timing Choice
Dimensions and Patterns
Package Size – Dimensions (Unit: mm)
[3]
2.7 x 2.4 x 0.75 mm (100% compatible with 2.5 x 2. 0 mm footprint)
Recommended Land Pattern (Unit: mm)
[4]
YXXXX
3.2 x 2.5 x 0.75 mm
2.2
#4
3.2 ± 0.05
#4
#3
#3
2.1
2.5 ± 0.05
0.9
0.7
YXXXX
#1
#2
1.9
#2
#1
0.75 ± 0.05
0.9
1.4
5.0 x 3.2 x 0.75 mm
2.54
5.0 ± 0.05
#4
#3
#3
2.39
#4
3.2 ± 0.05
0.8
1.1
YXXXX
#1
#2
2.2
0.75 ± 0.05
#2
#1
1.15
1.5
7.0 x 5.0 x 0.90 mm
7.0 ± 0.05
5.08
5.08
5.0 ± 0.05
2.6
YXXXX
1.1
3.81
0.90 ± 0.10
1.4
2.2
Notes:
3. Top marking: Y denotes manufacturing origin and XXXX denotes manufacturing lot number. The value of “Y” will depend on the assembly location of the device.
The PIC series of microcontrollers developed by Microchip in the United States adopts a unique design approach in hardware structure and instruction system. It has made some groundbreaking changes to ...
I encountered a problem when debugging the program. I tried to use the read protection function and wrote 0x00 to RDP, but I couldn't simulate it anymore. The program didn't execute from main() and ke...
Hello everyone, I am using 6713 to read the data from the microcontroller through the I2C0 port, working in slave mode. I have read the relevant routines and found that no interrupts are used. I would...
The core of a machine vision system is image acquisition and processing. All information comes from images, and image quality is crucial to the entire vision system. A good image can improve the st...[Details]
Most of the houses we live in now are elevator buildings, mainly because it is more convenient to go up and down the stairs! It can also make life more comfortable. It even helps to increase the ad...[Details]
"Have you set your calendar reminder?"
On August 24, Nvidia Robotics' official account posted a photo of a black gift box on a social media platform, with an attached greeting card sig...[Details]
As the main model among new energy vehicles, pure electric vehicles have received strong support and encouragement from the country in recent years, and their development is changing with each pass...[Details]
Recently,
Xpeng Motors and Xinlian Integrated Circuit jointly announced the mass production of China's first hybrid silicon carbide product.
Designed and developed by Xpeng Motors and joint...[Details]
On August 22, according to the Ministry of Industry and Information Technology's official website, my country's first mandatory national standard for the control of hazardous substances in electric...[Details]
Tires are a very important component for cars. They are related to the driving experience of the vehicle. We are almost inseparable from cars in our daily lives. For tires, according to the role of...[Details]
The 2025 China International Automotive Testing Exhibition will be held at the Shanghai World Expo Exhibition and Convention Center from August 27 to 29, 2025.
Clacton Seafront, UK, ...[Details]
On August 20, Geely announced its focus on "One Cockpit". Through a unified AI OS architecture, a unified AI Agent, and a unified user ID, it will achieve an All-in-One AI cockpit, create the first...[Details]
The difference between a series inverter and a parallel inverter is that they use different oscillation circuits. A series inverter connects L, R, and C in series, while a parallel inverter connect...[Details]
Speaking of the problem of vehicle spontaneous combustion, whether it is a pure electric vehicle or a fuel vehicle, there will be incidents of spontaneous combustion. For the same spontaneous combu...[Details]
Nascent Micro is launching devices covering a wide range of power applications, including gallium nitride (GaN) drivers, dual-channel automotive drivers, and battery protection MOSFETs.
...[Details]
AI distributed rendering architecture improves mobile phone rendering capabilities, and game performance tests can check frame generation indicators in real time
Shanghai, China, Aug...[Details]
As the electric vehicle industry continues to surge in today's society, while people are concerned about the appearance and interior of new energy vehicles, they are also concerned about the classi...[Details]
Reasons for the wear of the roller press reducer shaft:
1. Since the expansion sleeve is subjected to a large torque, the mating surfaces of the shaft and the sleeve move relative to each other...[Details]
MicroPython Open Source section
京公网安备 11010802033920号
EEWORLD
