XM28C020
2 Megabit Module
XM28C020
5 Volt, Byte Alterable E
2
PROM
DESCRIPTION
256K x 8 Bit
TYPICAL FEATURES
•
•
•
•
•
•
•
•
•
•
High Density 2 Megabit (256K x 8) Module
Access Time of 150ns at –55
°
C to +125
°
C
Base Memory Component: Xicor X28C513
Pinout conforms to JEDEC Standard for
2 Megabit E
2
PROM
Fast Write Cycle Times
—128 Byte Page Write
—Byte or Page Write Cycle: 5ms Typical
—Complete Memory Rewrite: 10 Seconds
Early End of Write Detection
—DATA Polling
—Toggle Bit Polling
Software Data Protection
Three Temperature Ranges
—Commercial: 0
°
C to +75
°
C
—Industrial: –40
°
to +85
°
C
—Military: –55
°
to +125
°
C
High Rel Module
—100% MIL-STD-883 Compliant Components
Endurance: 100,000 Cycles
The XM28C020 is a high density 2 Megabit E
2
PROM
comprised of four X28C513 LCCs mounted on a co-fired
multilayered ceramic substrate. Individual components
are 100% tested prior to assembly in module form and
then 100% tested after assembly.
The XM28C020 is configured 256K x 8 bit. The module
supports a 128-byte page write operation. This com-
bined with
DATA
Polling or Toggle Bit Polling, effectively
provides a 39µs/byte write cycle, enabling the entire
array to be rewritten in 10 seconds.
The XM28C020 provides the same high endurance and
data retention as the X28C513.
FUNCTIONAL DIAGRAM
X28C513
A0–A15
I/O0–I/O7
OE
WE
CE
X28C513
A0–A15
I/O0–I/O7
OE
WE
CE
PIN CONFIGURATION
NC
A16
A15
A12
A7
A6
A5
A4
A3
A2
A1
A0
I/O0
I/O1
I/O2
VSS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
XM28C020
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
VCC
WE
A17
A14
A13
A8
A9
A11
OE
A10
CE
I/O7
I/O6
I/O5
I/04
I/O3
A0–A15
I/O0–I/O7
OE
WE
CE
A16
A17
X28C513
A0–A15
I/O0–I/O7
OE
WE
CE
X28C513
A0–A15
I/O0–I/O7
OE
WE
CE
3872 FHD F02
3872 FHD F01
© Xicor, Inc. 1991, 1995, 1996 Patents Pending
3872-1.9 6/18/97 T1/C0/D0 SH
1
Characteristics subject to change without notice
XM28C020
DEVICE OPERATION
Read
Read operations are initiated by both
OE
and
CE
LOW.
The read operation is terminated by either
CE
or
OE
returning HIGH. This 2-line control architecture elimi-
nates bus contention in a system environment. The data
bus will be in a high impedance state when either
OE
or
CE
is HIGH.
Write
Write operations are initiated when both
CE
and
WE
are
LOW and
OE
is HIGH. The XM28C020 supports both a
CE
and
WE
controlled write cycle. That is, the address
is latched by the falling edge of either
CE
or
WE,
whichever occurs last. Similarly, the data is latched
internally by the rising edge of either
CE
or
WE,
which-
ever occurs first. A byte write operation, once initiated,
will automatically continue to completion, typically within
5ms (see Note 4).
Page Write Operation
The page write feature of the XM28C020 allows the
entire memory to be written in 10 seconds. Page write
allows two to 128 bytes of data to be consecutively
written to the XM28C020 prior to the commencement of
the internal programming cycle. The host can fetch data
from another device within the system during a page
write operation (change the source address), but the
page address (A
7
through A
17
) for each subsequent
valid write cycle to the part during this operation must be
the same as the initial page address.
The page write mode can be initiated during any write
operation. Following the initial byte write cycle, the host
can write an additional one to 127 bytes in the same
manner as the first byte was written. Each successive
byte load cycle, started by the
WE
HIGH to LOW
transition, must begin within 100µs of the falling edge of
the preceding
WE.
If a subsequent
WE
HIGH to LOW
transition is not detected within 100µs, the internal
automatic programming cycle will commence. There is
no page write window limitation. Effectively the page
DATA
Polling (I/O
7
)
The XM28C020 features
DATA
Polling as a method to
indicate to the host system that the byte write or page
write cycle has completed.
DATA
Polling allows a simple
bit test operation to determine the status of the
XM28C020, eliminating additional interrupt inputs or
external hardware. During the internal programming
cycle, any attempt to read the last byte written will
produce the complement of that data on I/O
7
(i.e., write
data = 0xxx xxxx, read data = 1xxx xxxx). Once the
programming cycle is complete, I/O
7
will reflect true
data. Note: If the XM28C020 is in the protected state and
an illegal write operation is attempted,
DATA
Polling will
not operate.
Toggle Bit (I/O
6
)
The XM28C020 also provides another method for deter-
mining when the internal write cycle is complete. During
the internal programming cycle I/O
6
will toggle from “1”
to “0” and “0” to “1” on subsequent attempts to read the
last byte written. When the internal cycle is complete the
toggling will cease and the device will be accessible for
additional read or write operations.
write window is infinitely wide, so long as the host
continues to access the device within the byte load cycle
time of 100µs.
Write Operation Status Bits
The XM28C020 provides the user two write operation
status bits. These can be used to optimize a system
write cycle time. The status bits are mapped onto the
I/O bus as shown in Figure 1.
Figure 1. Status Bit Assignment
I/O
DP
TB
5
4
3
2
1
0
RESERVED
TOGGLE BIT
DATA POLLING
3872 FHD F09
3
Recruitment
京公网安备 11010802033920号
EEWORLD
