EEWORLDEEWORLDEEWORLD

Part Number

Search

VL-MM8-1EBN

Description
1GB, DDR2 EX TEMP ROHS
Categoryaccessories   
File Size191KB,10 Pages
ManufacturerVersaLogic Corp.
Websitehttps://www.versalogic.com/
Environmental Compliance
Download Datasheet Parametric View All

VL-MM8-1EBN Overview

1GB, DDR2 EX TEMP ROHS

VL-MM8-1EBN Parametric

Parameter NameAttribute value
Accessory typememory module
Specification1GB(128Mx64)DDR2 SDRAM
Product Specifications
PART NO.:
VL470T2863A-E6S-I
REV: 1.0
General Information
1GB 128Mx64 DDR2 SDRAM NON-ECC UNBUFFERED SODIMM 200-PIN
Description
The VL470T2863A is a 128Mx64 DDR2 SDRAM high density SODIMM. This single rank memory module consists of
eight CMOS 128Mx8 bits with 8 banks DDR2 synchronous DRAMs in BGA packages and a 2K EEPROM in an 8-pin
TSSOP package. This module is a 200-pin small-outline dual in-line memory module and is intended for mounting
into an edge connector socket. Decoupling capacitors are mounted on the printed circuit board for each DDR2
SDRAM.
Features
200-pin, small-outline dual in-line memory module (SODIMM)
JEDEC pin out
Fast data transfer rate: PC2-5300
VDD = VDDQ = 1.8V +/-0.1V
JEDEC standard 1.8V (SSTL_18 compatible)
VDDSPD = 1.7V to 3.6V
Differential data strobe (DQS, DQS# ) option
Differential clock inputs (CK, CK#)
Four-bit pre-fetch architecture
DLL aligns DQ and DQS transition with CK
Nominal and dynamic on-die termination (ODT)
Programmable CAS# latency: 5 (DDR2-667)
Write latency = Read latency - 1 tCK
Eight internal component banks for concurrent operation
Programmable burst; length (4, 8)
Adjustable
data-output drive strength
Auto & self refresh, (8K/64ms refresh)
Serial presence detect (SPD) with EEPROM
Gold edge contacts
Lead-free, RoHS compliant
PCB: Height 30.00mm (1.181”), double sided component
o
o
Industrial temperature (T
OPER
): -40 C to +95 C (module screening using
commercial DRAM)
Notes: Double refresh rate is required when 85 C < T
OPER
<= 95 C.
T
OPER
is DRAM case temperature.
o
o
Pin Description
Pin Name
A0~A13
A10/AP
BA0~BA2
DQ0~DQ63
DQS0~DQS7
DQS0#~DQS7#
DM0~DM7
CK0, CK0#,
CK1, CK1#
ODT0
CKE0
CS0#
RAS#
CAS#
WE#
VDD
VSS
SA0~SA1
Function
Address Inputs
Address Input/ Autoprecharge
Bank Address Inputs
Data Input/Output
Data Strobes
Data Strobes Complement
Data Masks
Clock Inputs
On-die Termination Control
Clock Enables
Chip Selects
Row Address Strobes
Column Address Strobes
Write Enable
Voltage Supply
Ground
SPD Address
SPD Data Input/Output
SPD Clock Input
SPD Voltage Supply
SSTL_18 Reference Voltage
No Connect
Order Information:
VL470T2863A - E6 S X - I
OPERATING TEMPERATURE
I : Industrial screening
DRAM DIE
(Option)
DRAM MANUFACTURER
S - SAMSUNG
MODULE SPEED
E6: PC2-5300 @ CL5
VL: Lead-free/RoHS
SDA
SCL
VDDSPD
VREF
NC
Tel 949.888.2444 – 30052 Tomas, Rancho Santa Margarita, CA 92688 USA –
www.virtium.com
1
Zener diode problem
Generally, a Zener diode has izk, the minimum inflection point current, izt, the general working current, and zzt, the impedance when izt. Why is zzt multiplied by izt not equal to the stable voltage?...
dlcnight Analog electronics
Analysis of the working principles of seven triode collector DC circuits
[i=s] This post was last edited by tiankai001 on 2019-1-8 11:12 [/i] [b]VII. Deformed Collector DC Circuit [/b] [align=left] [color=rgb(34, 34, 34)] [font="]The following figure is a deformed circuit ...
tiankai001 Analog electronics
The STM32F769 development board has been arranged for delivery (the shipping number is included in the post)
Related activities: [url=https://bbs.eeworld.com.cn/thread-505695-1-1.html]https://bbs.eeworld.com.cn/thread-505695-1-1.html[/url] [size=4]Hi, STM32F769 evaluation team, F769 has flown to you, the fol...
nmg stm32/stm8
Op amp output square wave deformation
I used RC to simulate my load. During the simulation, I found that the voltage of the square wave generated by the waveform generator on my load was perfect (positive and negative symmetry).However, I...
YYYYYYYYY7YYY Analog electronics
Request the MSP-EXP430FR5739 Experimenter Kit
...
sciencekn1 Microcontroller MCU
My emergency light finally emitted a very weak light
Today I finally finished welding my emergency light. It finally emits a very weak light. Not only does it not serve the purpose of emergency lighting, but you can't tell if it is glowing unless you lo...
西门 DIY/Open Source Hardware

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 810  2644  1622  1693  1588  17  54  33  35  32 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号