EEWORLDEEWORLDEEWORLD

Part Number

Search

5363-2.5MMX50M

Description
ACF 2.5MMX50M 0.098"X165'
Categoryunclassified   
File Size149KB,5 Pages
Manufacturer3M
Websitehttp://3M.com/esd
Environmental Compliance
Download Datasheet View All

5363-2.5MMX50M Overview

ACF 2.5MMX50M 0.098"X165'

Technical Data
November 2013
3M
Anisotropic Conductive Film 5363
Product Description
3M™ Anisotropic Conductive Film (ACF) 5363 is a
heat-bondable, electrically conductive adhesive film.
The unbonded film is non-tacky at room temperature
and consists of a thermoset-thermoplastic adhesive
matrix randomly loaded with conductive particles. These
particles allow inter-connection of circuit lines through
the adhesive thickness, but are spaced far enough
apart for the product to be electrically insulating in the
plane of the adhesive. Application of heat and pressure
causes the adhesive to flow and to bring the circuit pads
into contact by trapping the conductive particles. The
adhesive rapidly cures at modest bonding temperature.
The 3M ACF 5363 may be used to bond a flexible printed
circuit to another flexible printed circuit or to a printed
circuit board.
Typical Physical Properties and
Performance Characteristics
Note:
The following technical information and data should
be considered representative or typical only and
should not be used for specification purposes.
Design Requirements
Property
Minimum Space Between
Conductors
Minimum Pitch
Minimum Pad Area
Value
100
(4)
200
(8)
0.15
(240)
Units
micron
(mil)
micron
(mil)
sq. mm
(sq. mil)
Ambient Physical Properties
Property
(1)
Interconnect
Resistance
Peel Strength
(4)
Test Substrates
Flex-to-
PC board
(2)
Flex-to-
PC board
(2)
Value
Test Method
< 20 mOhms 3M TM-2314
(3)
> 700 gf/cm 3M TM-2313
(5)
Construction
General Properties
Property
Adhesive Type
Particle Type
Particle Size
Liner Type
Adhesive Thickness
Liner Thickness
Value
(1)
Thermosetting Type
Gold-Coated Nickel
10 micron
Polyester Film with Silicone Release
40 micron
50 micron
(4)
(5)
(2)
(3)
For a given application, values may differ depending on particular substrate
material or type of circuitry.
Measured for gold/nickel/copper polyimide flex circuits bonded to printed
circuit board. Contact overlap area was 0.15 sq. mm. Pad pitch was 200
microns.
3M internal test method TM-2314 based on test method IPC 650 – Section
2.6.24. The flex has the shorting strap located near the bond-line to
approximate a 4-wire test structure and eliminate most extraneous
resistance in the measurement due to the circuit lines.
Results listed for minimum bonding conditions of 160°C x 5 sec. Higher
values are possible with increase in bonding temperature or time.
3M internal test method TM-2313 based on test method IPC 650 –
Section 2.4.9.1.
Talk about several important indicators for selecting test instruments
Taking digital oscilloscope as an example, many users may know some traditional indicators of oscilloscope, such as bandwidth, sampling rate, memory depth, etc., and even appear in the selection of mo...
qwqwqw2088 Test/Measurement
[MSP430 Sharing] Design of Intelligent Remote Temperature and Humidity Monitoring System
This paper introduces the design of a universal temperature and humidity measurement system, and proposes a design scheme of a multi-point measurement system with a highly integrated temperature and h...
鑫海宝贝 Microcontroller MCU
ARM remote control program
ARM remote control program...
darktemple ARM Technology
16-bit comparator
I want the source code of a 16-bit size comparator, VHDL. Is it slow to use if statements? I want to use the corresponding bit XOR, then find the highest bit 1 and XOR the two. What is the simplest wa...
qinxuewei101 Embedded System
Oh, my brain is not working well. I don’t know what’s wrong with the simplest program. . . .
I bought the lunchpad learning board but never played with it until these few days. Today I wrote a simple program but it was wrong. I don't know where I went wrong... :Sad: #include "io430.h" int mai...
小小白 Microcontroller MCU
vxworks task monitoring
When I use browse to monitor the task status on the target machine, I find that some tasks are displayed in red, but turn black after a while, while most tasks are displayed in black. Can anyone tell ...
sealfox Real-time operating system RTOS

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2638  2850  2602  2446  299  54  58  53  50  7 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号