XC6107A122 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > XC6107A122

Preview

XC6107A122: DescriptionCMOS Voltage Detector; File Size525KB，26 Pages; ManufacturerTOREX; Websitehttp://www.torex.co.jp/chinese/

Download Datasheet View All

XC6107A122 Overview

CMOS Voltage Detector

Preview

Download Datasheet

View All

Preliminary

◆CMOS

Voltage Detector

◆Manual

Reset Input

◆Watchdog

Functions

◆Built-in

Delay Circuit

◆Detect

Voltage Range: 1.6~5.0V, ± 2%

◆Reset

Function is Selectable

DFL

(Low When Detected)

DFH

(High When Detected)

■APPLICATIONS

●Microprocessor

reset circuits

●Memory

battery backup circuits

●System

power-on reset circuits

●Power

failure detection

■GENERAL

DESCRIPTION

■FEATURES

Detect Voltage Range

Hysteresis Range

: 1.6V ~ 5.0V, +2%

(100mV increments)

: V

x 5%, TYP.

(XC6101~XC6107)

x 0.1%, TYP.

(XC6111~XC6117)

: 1.0V ~ 6.0V

The XC6101~XC6107, XC6111~XC6117 series are

groups of high-precision, low current consumption voltage

detectors with manual reset input function and watchdog

functions incorporating CMOS process technology. The

series consist of a reference voltage source, delay circuit,

comparator, and output driver.

With the built-in delay circuit, the XC6101 ~ XC6107,

XC6111 ~ XC6117 series’ ICs do not require any external

components to output signals with release delay time.

Moreover, with the manual reset function, reset can be

asserted at any time. The ICs produce two types of

output; V

DFL

(low when detected) and V

DFH

(high when

detected).

With the XC6101 ~ XC6105, XC6111 ~ XC6115 series’

ICs, the WD pin can be left open if the watchdog function

is not used.

Whenever the watchdog pin is opened, the internal

counter clears before the watchdog timeout occurs.

Since the manual reset pin is internally pulled up to the V

pin voltage level, the ICs can be used with the manual

reset pin left unconnected if the pin is unused.

The detect voltages are internally fixed 1.6V ~ 5.0V in

increments of 100mV, using laser trimming technology.

Six watchdog timeout period settings are available in a

range from 6.25msec to 1.6sec.

Seven release delay time 1 are available in a range from

3.13msec to 1.6sec.

Operating Voltage Range

Detect Voltage Temperature

Characteristics

: +100ppm/

C (TYP.)

Output Configuration

: N-channel open drain,

CMOS

Watchdog Pin

: Watchdog input

If watchdog input maintains

‘H’ or ‘L’ within the watchdog

timeout period, a reset signal

is output to the RESET

output pin

Manual Reset Pin

: When driven ‘H’ to ‘L’ level

signal, the MRB pin voltage

asserts forced reset on the

output pin.

Release Delay Time

: 1.6sec, 400msec, 200msec,

100msec, 50msec, 25msec,

3.13msec (TYP.) can be

selectable.

Watchdog Timeout Period

: 1.6sec, 400msec, 200msec,

100msec, 50msec,

6.25msec (TYP.) can be

selectable.

■TYPICAL

APPLICATION CIRCUIT

■TYPICAL

PERFORMANCE

CHARACTERISTICS

●Supply

Current vs. Input Voltage

XC61X1~XC61X5 (2.7V)

Supply Current:

ISS (µA)

Input Voltage:

VIN (V)

Ta=-40

℃

Ta=25

℃

Ta=85

℃

* Not necessary with CMOS output products.

* ‘x’ represents both ‘0’ and ‘1’. (ex. XC61x1⇒XC6101 and XC6111)

XC6101_07_XC6111_17 ETR0207_009

1/26

Recommended Resources

LED light circuit diagram powered by solar cells

KA2312 (toy) radio remote control transmission control and regulation circuit - basic test circuit

Average minus minimum comparison circuit diagram

SBX1483—11/12/51/52 (TVs, VCRs, audio equipment, air conditioners and toys) infrared remote control receiving circuit

0～150V regulated power supply circuit

Air compressor contactor welding protection circuit

Questions about simulation in Quartus: It's like this. I wrote a small Verilog program, compiled it successfully, and then after creating the bdf file, I compiled it again, but an error occurred. The error is: Error: Can't compile duplicat...; zany.peng Embedded System

Use AM5728 EVM to make and download 6678 program: In this step, the eight .out files can be combined into one file for network transmission through the tool, and then sent to the 6678EVM for running.1. Execute the EMACboot_8core.sh script on the AM57...; Jacktang DSP and ARM Processors

Urgently hiring part-time PCB design engineer: The company is committed to the development and sales of high-end virtual instruments based on computers, and aims to become the number one in high-end virtual instruments! Welcome those who are inter...; kckj Recruitment

Comments are rewarded | [Discovery] Enter the world of TI millimeter-wave radar and quickly acquire design skills: Comments are rewarded | [Discovery] Enter the world of TI millimeter-wave radar and quickly acquire design skillsClick here to enter the eventEvent time: From now on to November 26, 2019Event process:...; EEWORLD社区 TI Technology Forum

[Question] How to write the IEEE 1394 driver?: Please help, how many steps are there to drive the IEEE1394 interface to the PCI bus adapter card? How can I make IEEE1394 work in synchronous transfer mode?...; k77777 Embedded System

Questions about rts2800_fpu32.lib: In the process of motorware, for example, proj_lab04a uses the rts2800_fpu32.lib library, but why does it use MATH_TYPE = IQ_MATH instead of MATH_TYPE = FLOAT_MATH? Thank you!...; zhoumin Microcontroller MCU

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components