CRCW...C e3
www.vishay.com
Vishay
Lead (Pb)-free Thick Film, Rectangular
Commodity Chip Resistors
FEATURES
• High volume product suitable for commercial
applications
• Stability (R/R
1 % for 1000 h at
70 °C)
• Lead (Pb)-free solder contacts on Ni barrier
layer
• Metal glaze on ceramic
• Material categorization: for definitions of compliance
please see
www.vishay.com/doc?99912
STANDARD ELECTRICAL SPECIFICATIONS
MODEL
CASE
SIZE
INCH
CASE
SIZE
METRIC
POWER RATING
P
70 °C
W
0.063
LIMITING
ELEMENT
VOLTAGE
MAX. V
50
TEMPERATURE
COEFFICIENT
ppm/K
± 100
± 200
TOLERANCE
%
±1
±5
RESISTANCE
RANGE
1R0 to 10M
1R0 to 10M
E-SERIES
E24; E96
E24
CRCW0402...C
0402
RR 1005M
Zero-Ohm-Resistor:
R
max.
= 20 m,
I
max.
at 70 °C = 1.5 A
0.10
75
± 100
± 200
±1
±5
1R0 to 10M
1R0 to 10M
E24; E96
E24
CRCW0603...C
0603
RR 1608M
Zero-Ohm-Resistor:
R
max.
= 20 m,
I
max.
at 70 °C = 2.0 A
0.125
150
± 100
± 200
±1
±5
1R0 to 10M
1R0 to 10M
E24; E96
E24
CRCW0805...C
0805
RR 2012M
Zero-Ohm-Resistor:
R
max.
= 20 m,
I
max.
at 70 °C = 2.5 A
0.25
200
± 100
± 200
±1
±5
1R0 to 10M
1R0 to 10M
E24; E96
E24
CRCW1206...C
1206
RR 3216M
Zero-Ohm-Resistor:
R
max.
= 20 m,
I
max.
at 70 °C = 3.5 A
Notes
• These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over
operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime
• Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material
TECHNICAL SPECIFICATIONS
PARAMETER
Rated dissipation at 70°C
(1)
Limiting element voltage
U
max.
AC/DC
Insulation voltage
U
ins.
(1 min)
Insulation resistance
Category temperature range
Failure rate
Weight/1000 pieces
UNIT
W
V
V
°C
h
-1
g
0.65
2
CRCW0402...C
0.063
50
> 75
CRCW0603...C
0.10
75
> 100
> 10
9
- 55 to + 155
0.1 x 10
-9
5.5
10
CRCW0805...C
0.125
150
> 200
CRCW1206...C
0.25
200
> 300
Note
(1)
The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the
printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceeded
Revision: 02-Nov-17
Document Number: 28773
1
For technical questions, contact:
ff3aresistors@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
CRCW...C e3
www.vishay.com
Vishay
PART NUMBER AND PRODUCT DESCRIPTION
PART NUMBER: CRCW0603562RFKECC
C
R
C
W
0
6
0
3
5
6
2
TCR
R
F
K
E
C
C
SPECIAL
Up to 2 digits
C
= commodity
MODEL/SIZE
CRCW0402
CRCW0603
CRCW0805
CRCW1206
VALUE
R
= decimal
K
= thousand
M
= million
0000
= jumper
TOLERANCE
F
= ± 1.0 %
J
= ± 5.0 %
Z
= jumper
PACKAGING
EA, EB,
EC, ED,
EE
K
= ± 100 ppm/K
N
= ± 200 ppm/K
0
= jumper
PRODUCT DESCRIPTION: CRCW0603-C 100 562R 1 % ET6 E3
CRCW0603-C
MODEL
CRCW0402-C
CRCW0603-C
CRCW0805-C
CRCW1206-C
100
TCR
± 200
ppm/K
± 100
ppm/K
562R
RESISTANCE
VALUE
10R
= 10
562R
= 562
10K
= 10.0 k
1M
= 1 M
0R0
= jumper
1%
TOLERANCE
±
5%
±
1%
ET6
PACKAGING
ET1, ET5,
ET6, ET7,
EF4
e3
LEAD (Pb)-FREE
e3
= pure tin
termination
finish
PACKAGING
TYPE / SIZE
CRCW0402…C
CODE
ED = ET7
EE = EF4
EA = ET1
EB = ET5
EC = ET6
EA = ET1
EB = ET5
EC = ET6
EA = ET1
EB = ET5
EC = ET6
QUANTITY
10 000
50 000
5000
10 000
20 000
5000
10 000
20 000
5000
10 000
20 000
PACKAGING STYLE
WIDTH
PITCH
2 mm
PACKAGING
DIMENSIONS
Ø 180 mm/7"
Ø 330 mm/13"
Ø 180 mm/7"
Ø 254 mm/10"
Ø 330 mm/13"
Ø 180 mm/7"
Ø 254 mm/10"
Ø 330 mm/13"
Ø 180 mm/7"
Ø 254 mm/10"
Ø 330 mm/13"
CRCW0603…C
4 mm
Paper tape acc. to
IEC 60286-3, Type 1a
8 mm
4 mm
CRCW0805…C
CRCW1206…C
4 mm
DIMENSIONS
SIZE
INCH METRIC
0402
1005
0603
1608
0805
2012
1206
3216
L
1.0 ± 0.10
1.60 ± 0.10
2.0 ± 0.10
3.05 ± 0.10
DIMENSIONS
(in millimeters)
W
0.5 ± 0.05
0.80 ± 0.10
1.25 ± 0.15
1.55 ± 0.10
H
T1
0.30 ± 0.05 0.25 ± 0.10
0.45 ± 0.10 0.3 ± 0.2
0.50 ± 0.10 0.35 ± 0.15
0.55
+ 0.10
- 0.05
T2
0.2 ± 0.1
0.3 ± 0.2
0.35 ± 0.2
0.45 ± 0.2
SOLDER PAD DIMENSIONS
(1)
(in millimeters)
REFLOW SOLDERING
WAVE SOLDERING
a
b
l
a
b
l
0.4
0.6
0.5
0.5
0.9
1.0
0.9
0.9
1.0
0.7
1.3
1.2
0.9
1.3
1.3
0.9
1.7
2.0
1.1
1.7
2.3
0.35 ± 0.15
Note
(1)
The rated dissipation applies only if the permitted film temperature is not exceeded. Furthermore, a high level of ambient temperature or of
power dissipation may raise the temperature of the solder joint, hence special solder alloys or board materials maybe required to maintain
the reliability of the assembly. Specified power rating above 125 °C requires dedicated heat-sink pads, which depend on board materials.
The given solder pad dimensions reflect the considerations for board design and assembly as outlined e.g. in standards IEC 61188-5-x, or
in publication IPC-7351. They do not guarantee any supposed thermal properties, particularly as these are also strongly influenced by many
other parameters. Still the given solder pad dimensions will be found adequate for most general applications
Revision: 02-Nov-17
Document Number: 28773
2
For technical questions, contact:
ff3aresistors@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
CRCW...C e3
www.vishay.com
FUNCTIONAL PERFORMANCE
Rated Power in %
120
100
Vishay
80
60
40
20
0
- 55
- 25
0
25
50
Derating
TEST PROCEDURES AND REQUIREMENTS
EN 60115-1
CLAUSE
IEC 60068-2
TEST
METHOD
75
100
125
155 175
70 Ambient Temperature in
°C
REQUIREMENTS PERMISSIBLE
CHANGE (R)
TEST
PROCEDURE
STABILITY
CLASS 1
OR BETTER
1
to 10 M
±1%
± 100 ppm/K
STABILITY
CLASS 2
OR BETTER
1
to 10 M
±5%
± 200 ppm/K
Stability for product types:
CRCW...C e3
4.5
4.8.4.2
4.13
-
-
-
Resistance
Temperature
coefficient
Short time
overload
-
(20/- 55/20) °C and
(20/125/20) °C
U
= 2.5 x
P
70
x
R
2 x
U
max.;
5 s
Solder bath method;
Sn60Pb40
non activated flux;
(235 ± 5) °C
(2 ± 0.2) s
Solder bath method;
Sn96.5Ag3Cu0.5
non activated flux;
(245 ± 5) °C
(3 ± 0.3) s
± (2 %
R
+ 0.1
)
Good tinning ( 95 % covered)
no visible damage
4.17.5
58 (Td)
Solderability
Pre-aging
4 h at 155 °C,
dryheat
Good tinning ( 95 % covered)
no visible damage
4.18.2
4.19
58 (Td)
14 (Na)
Resistance to
soldering heat
Rapid change
of temperature
Damp heat,
steady state
Operation at low
temperature
Solder bath method
(260 ± 5) °C; (10 ± 1) s
30 min. at - 55 °C;
30 min. at 125 °C;
5 cycles
(40 ± 2) °C;
56 days;
(93 ± 3) % RH
-55 °C, 1 h
U
=
P
70
x
R
U
max.;
1.5 h on; 0.5 h off;
70 °C; 1000 h
70 °C; 8000 h
± (1%
R
+ 0.05
)
± (0.25 %
R
+ 0.05
)
± (0.5 %
R
+ 0.05
)
4.24
4.36
78 (Cab)
-
± (1 %
R
+ 0.05
)
± (2 %
R
+ 0.1
)
± (1 %
R
+ 0.05
)
4.25.1
-
Endurance
at 70 °C
± (1 %
R
+ 0.05
)
± (2 %
R
+ 0.1
)
± (1 %
R
+ 0.05
)
± (2 %
R
+ 0.1
)
± (4 %
R
+ 0.1
)
± (2 %
R
+ 0.1
)
4.25.3
-
Endurance at
upper category
temperature
155 °C, 1000 h
Revision: 02-Nov-17
Document Number: 28773
3
For technical questions, contact:
ff3aresistors@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
CRCW...C e3
www.vishay.com
Vishay
APPLICABLE SPECIFICATIONS
• EN 60115-1
• EN 140400
• EN 140401-802
• IEC 60068-2-X
• IEC 60286-3
Generic specification
Sectional specification
Detail specification
Variety of environmental test procedures
Packaging of SMD components
Revision: 02-Nov-17
Document Number: 28773
4
For technical questions, contact:
ff3aresistors@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of
typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding
statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a
particular product with the properties described in the product specification is suitable for use in a particular application.
Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over
time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.
Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for
such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document
or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
© 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED
Revision: 08-Feb-17
1
Document Number: 91000
Embedded System
京公网安备 11010802033920号
EEWORLD
