530SA378M000DG datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > oscillator> 530SA378M000DG

530SA378M000DG: DescriptionLVDS Output Clock Oscillator, 378MHz Nom, ROHS COMPLIANT, SMD, 6 PIN; Categoryoscillator; File Size215KB，12 Pages; ManufacturerSilicon Laboratories Inc; Environmental Compliance

Download Datasheet Parametric View All

530SA378M000DG Overview

LVDS Output Clock Oscillator, 378MHz Nom, ROHS COMPLIANT, SMD, 6 PIN

530SA378M000DG Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
Maker	Silicon Laboratories Inc
package instruction	ROHS COMPLIANT, SMD, 6 PIN
Reach Compliance Code	unknown
Is Samacsys	N
Other features	TRAY
maximum descent time	0.35 ns
Frequency Adjustment - Mechanical	NO
frequency stability	50%
JESD-609 code	e4
Manufacturer's serial number	530
Installation features	SURFACE MOUNT
Nominal operating frequency	378 MHz
Maximum operating temperature	85 °C
Minimum operating temperature	-40 °C
Oscillator type	LVDS
physical size	7.0mm x 5.0mm x 1.85mm
longest rise time	0.35 ns
Maximum supply voltage	2.75 V
Minimum supply voltage	2.25 V
Nominal supply voltage	2.5 V
surface mount	YES
maximum symmetry	55/45 %
Terminal surface	Nickel/Gold (Ni/Au)
Base Number Matches	1

Preview

Download Datasheet

View All

S i 5 3 0 / 5 31

EVISION

R Y S TA L

S C I L L A T O R

(XO)

(10 M H

Z T O

1.4 G H

)

Features

Available with any-rate output

frequencies from 10 MHz to 945 MHz

and select frequencies to 1.4 GHz

3rd generation DSPLL

with superior

jitter performance

3x better frequency stability than

SAW-based oscillators

Internal fixed crystal frequency

ensures high reliability and low

aging

Available CMOS, LVPECL,

LVDS, and CML outputs

3.3, 2.5, and 1.8 V supply options

Industry-standard 5 x 7 mm

package and pinout

Pb-free/RoHS-compliant

Si5602

Ordering Information:

See page 7.

Applications

SONET/SDH

Networking

SD/HD video

Test and measurement

Clock and data recovery

FPGA/ASIC clock generation

Pin Assignments:

See page 6.

(Top View)

GND

Description

The Si530/531 XO utilizes Silicon Laboratories’ advanced DSPLL circuitry

to provide a low jitter clock at high frequencies. The Si530/531 is available

with any-rate output frequency from 10 to 945 MHz and select frequencies to

1400 MHz. Unlike a traditional XO, where a different crystal is required for

each output frequency, the Si530/531 uses one fixed crystal to provide a

wide range of output frequencies. This IC based approach allows the crystal

resonator to provide exceptional frequency stability and reliability. In addition,

DSPLL clock synthesis provides superior supply noise rejection, simplifying

the task of generating low jitter clocks in noisy environments typically found in

communication systems. The Si530/531 IC based XO is factory configurable

for a wide variety of user specifications including frequency, supply voltage,

output format, and temperature stability. Specific configurations are factory

programmed at time of shipment, thereby eliminating long lead times

associated with custom oscillators.

CLK–

CLK+

Si530 (LVDS/LVPECL/CML)

GND

Functional Block Diagram

CLK– CLK+

CLK

Si530 (CMOS)

Fixed

Frequency

Any-rate

10–1400 MHz

DSPLL

Clock

Synthesis

GND

CLK–

CLK+

Si531 (LVDS/LVPECL/CML)

GND

Rev. 1.1 6/07

Si530/531

Recommended Resources

Two-wire remote AC electronic thermostat (gas or oil furnace control)

JG series photoelectric relay circuit a

Ground conductivity measurement circuit

PH detection circuit

Rapid Battery Charger For icom IC-2A

Resistor-capacitor phase failure protection circuit

Ask about PIC18 floating point error: [table=98%,rgb(238, 238, 238)] [tr][td]Please ask about PIC18 floating point error. I recently used PICC 9.66, set it to long double xx u32 yy; xx=0.12345678; xx*=100000000; yy=(u32) xx; and then disp...; hyf8 Microchip MCU

Platform Builder cannot create a new project: Platform Builder cannot create a new project. I am using VS2005, but it says that it cannot find winceroot and specify the path. However, I have followed the installation steps completely. Please help...; zhongzhong Embedded System

Who has the Chinese parameter introduction of 74c245?: Who has the Chinese parameter introduction of 74c245?...; why_92 51mcu

Urgent question: How to use cedb database under wince: Now I need to use the cedb database, but the write operation CeWriteRecordProps always fails, and the return value is 0. The GetLastError says it is a parameter problem. I have read previous posts. Be...; 232222222 Embedded System

Effects of Compensating Input Capacitance on Voltage-Feedback and Current-Feedback Operational Amplifiers Used in Current-to-Voltage Converters: ...; gaoyang9992006 ADI Reference Circuit

[Video Sharing] Power Design Tip 38: Use a Simple Latch Circuit to Protect the Power Supply: Have you ever needed a simple, low-cost latch circuit? Power Tips 38 gives you the most satisfactory choice[flash]http://player.youku.com/player.php/sid/XNDExMzk2NDE2/v.swf[/flash]For more Texas Instr...; 德州仪器_视频 Analog electronics

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components