3M 2552 1.5" X 1.25"-100 datasheet, PDF

Datasheet> All Categories > accessories> 3M 2552 1.5" X 1.25"-100

3M 2552 1.5" X 1.25"-100: DescriptionTAPE DAMP 1 1/2"X 1 1/4" 100/RL; Categoryaccessories; File Size109KB，4 Pages; Manufacturer3M; Websitehttp://3M.com/esd; Environmental Compliance

Download Datasheet Parametric View All

3M 2552 1.5" X 1.25"-100 Overview

TAPE DAMP 1 1/2"X 1 1/4" 100/RL

3M 2552 1.5" X 1.25"-100 Parametric

Parameter Name	Attribute value
Tape type	damping foil
Adhesive	acrylic acid
base fabric, carrier	Aluminum, extremely soft
thickness	0.0150"（15.0 mils，0.381mm）
Thickness - Adhesive	0.0050"（5.0 mils，0.127mm）
Thickness - base fabric, carrier	0.0100"（10.0 mils，0.254mm）
width	1.50"（38.10mm）1 1/2"
length	1.25"（31.75mm）1 1/4"
color	transparent
use	-
temperature range	-25°F ~ 176°F（-32°C ~ 80°C）
shelf life	-
Shelf life start date	-

Preview

Download Datasheet

View All

Damping Foil

2552

Technical Data

January, 2012

Product Description

3M™ Damping Foil 2552 consists of a room temperature pressure sensitive

viscoelastic polymer on a dead soft aluminum foil and is

designed for application

to vibrating panels and support members.

The combination of viscoelastic

polymer and an aluminum foil backing (a constrained layer damper, or CLD) has

proved to be a unique construction with exceptional ability to control resonant

vibrations in the temperature range of 32° to 140°F (0° to 60°C), with survivability

from -25° to 175°F (-32° to 80°C).

Typical Damping

Properties

The high-energy dissipative polymer used in 3M damping foil 2552 can afford

excellent control of resonance-induced vibrations. When applied to a vibrating

structure, the polymer used in 3M damping foil 2552 converts vibration to negligible

heat. Vibration amplitudes and structure-borne noise can be consequentially reduced.

The performance of most damping devices is highly dependent on the interaction

between the device and the system to which it is applied. A constrained layer control

system is no different than a typical damping device and its ability to provide the

desired performance is affected by parameters other than temperature and frequency.

Namely the geometry, stiffness and the structure to which the control system is applied

will affect the performance.

The loss factor of a material is a dynamic property that can define damping

performance:

The following data are the results of 3M damping foil 2552 being tested per ASTM

E756-83. A sample was applied to a 8.0 inch by 0.5 inch by 0.06 inch steel beam.

The beam was tested over a temperature range of -40° to 140°F, in increments of

10°F. Beam modes 2 through 7 were monitored for system damping measurements.

3M™ Damping Foil 2552

™

Damping Foil

2552

Technical Information

The technical information, recommendations and other statements contained in this document are

based upon tests or experience that 3M believes are reliable, but the accuracy or completeness of such

information is not guaranteed.

Product Use

Many factors beyond 3M’s control and uniquely within user’s knowledge and control can affect the use

and performance of a 3M product in a particular application. Given the variety of factors that can affect

the use and performance of a 3M product, user is solely responsible for evaluating the 3M product and

determining whether it is fit for a particular purpose and suitable for user’s method of application.

Warranty,

Limited Remedy,

and Disclaimer

Unless an additional warranty is specifically stated on the applicable 3M product packaging or product

literature, 3M warrants that each 3M product meets the applicable 3M product specification at the time

3M ships the product. 3M MAKES NO OTHER WARRANTIES OR CONDITIONS, EXPRESS OR

IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY IMPLIED WARRANTY

OR CONDITION ARISING OUT OF A COURSE OF DEALING, CUSTOM OR USAGE OF TRADE.

If the 3M product does not conform to this warranty, then the sole and exclusive remedy is, at 3M’s

option, replacement of the 3M product or refund of the purchase price.

Limitation of Liability

Except where prohibited by law, 3M will not be liable for any loss or damage arising from the 3M product,

whether direct, indirect, special, incidental or consequential, regardless of the legal theory asserted,

including warranty, contract, negligence or strict liability.

ISO 9001: 2008

This Industrial Adhesives and Tapes Division product was manufactured under a 3M quality system registered to ISO 9001: 2008 standards.

Industrial Adhesives and Tapes Division

3M Center, Building 225-3S-06

St. Paul, MN 55144-1000

800-362-3550 • 877-369-2923 (Fax)

www.3M.com/industrial

Recycled Paper

40% pre-consumer

10% post-consumer

3M is a trademark of 3M Company.

Printed in U.S.A.

-4-

Recommended Resources

Paper tension control circuit

AC circuit of emitter coupled differential circuit

Notch filter circuit using three operational amplifiers

Sawtooth wave oscillator using 555 time base circuit

Class A and B complementary symmetrical circuits

Computer motherboard circuit diagram 440LX2_27

Does the thermal pad on the back of the THS3001 need to be connected to the ground plane?: [i=s] This post was last edited by dontium on 2015-1-23 13:12 [/i] rt, today I was studying the chip manual of THS3001 and found that THS3001 also uses PowerPad technology, but the chip manual does no...; GXT_Python Analogue and Mixed Signal

E There are good books in the gold mine. Read one.: I won’t say much, just look at the picture and you will know....; dongguanze Talking

How to set the coordinate mapping method in EVC: The coordinate mapping method in vc++ can be set directly through SetMapMade(), but EVC drawing cannot. How can I solve this problem? ? ? Thank you...; nwuwmz Embedded System

Principles and requirements for the 2009 National Undergraduate Electronic Design Competition: [i=s]This post was last edited by paulhyde on 2014-9-15 09:30[/i][b][font=华文中宋][size=16pt][font=宋体]I. Principles and requirements of proposition[/font][/size][/font][/b] [font=宋体][font=新宋体-18030][size...; open82977352 Electronics Design Contest

A small problem in the FPGA course design, please help me take a look...: Recently, the teacher assigned a course design to realize a music jukebox using FPGA. Store 3 music scores in ROM, and then switch songs by pressing buttons. The specific requirements are as follows: ...; panxiao FPGA/CPLD

In the ECG common mode rejection ratio test, why is a 20Vrms/50Hz sinusoidal signal selected as the test signal?: As the title says, I have looked at the common mode rejection ratio test schemes of YY1139 and IEC60601-2-25 before. I don’t quite understand why the 20Vrms/50Hz sine test signal is selected. I would ...; dswu233 Analog electronics

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components