SIT8208AC-G1-18E-26.000000Y datasheet, PDF

Datasheet> All Categories > Passive components> SIT8208AC-G1-18E-26.000000Y

Preview

SIT8208AC-G1-18E-26.000000Y: Description-20 TO 70C, 2520, 20PPM, 1.8V, 2; CategoryPassive components; File Size750KB，15 Pages; ManufacturerSiTime; Environmental Compliance

Download Datasheet View All

SIT8208AC-G1-18E-26.000000Y Overview

-20 TO 70C, 2520, 20PPM, 1.8V, 2

Preview

Download Datasheet

View All

SiT8208

Ultra Performance Oscillator

The Smart Timing Choice

Features



Applications



Any frequency between 1 and 80 MHz accurate to 6 decimal places

100% pin-to-pin drop-in replacement to quartz-based oscillators

Ultra low phase jitter: 0.5 ps (12 kHz to 20 MHz)

Frequency stability as low as ±10 PPM

Industrial or extended commercial temperature range

LVCMOS/LVTTL compatible output

Standard 4-pin packages: 2.5 x 2.0, 3.2 x 2.5, 5.0 x 3.2,

7.0 x 5.0 mm x mm

Instant samples with

Time Machine II

and

field programmable

oscillators

Outstanding silicon reliability of 2 FIT or 500 million hour MTBF

Pb-free, RoHS and REACH compliant

Ultra short lead time

SATA, SAS, Ethernet, PCI Express, video, WiFi

Computing, storage, networking, telecom, industrial control

Electrical Characteristics

[1]

Parameter

Output Frequency Range

Frequency Stability

Symbol

F_stab

Min.

-10

-20

-25

-50

First year Aging

10-year Aging

Operating Temperature Range

T_use

F_aging

-1.5

-5

-20

-40

Supply Voltage

Vdd

1.71

2.25

2.52

2.97

Current Consumption

OE Disable Current

Idd

I_OD

–

Standby Current

I_std

–

Duty Cycle

Rise/Fall Time

Output Voltage High

Output Voltage Low

Input Voltage High

Input Voltage Low

Input Pull-up Impedance

Tr, Tf

VOH

VOL

VIH

VIL

Z_in

–

90%

–

70%

–

Typ.

–

1.8

2.5

2.8

3.3

–

1.2

–

100

–

Max.

+10

+20

+25

+50

+1.5

+70

+85

1.89

2.75

3.08

3.63

–

10%

–

30%

250

–

Unit

MHz

PPM

°C

A

Vdd

kΩ

MΩ

15 pF load, 10% - 90% Vdd

IOH = -6 mA, IOL = 6 mA, (Vdd = 3.3V, 2.8V, 2.5V)

IOH = -3 mA, IOL = 3 mA, (Vdd = 1.8V)

No load condition, f = 20 MHz, Vdd = 2.5V, 2.8V or 3.3V

No load condition, f = 20 MHz, Vdd = 1.8V

Vdd = 2.5V, 2.8V or 3.3V, OE = GND, output is Weakly Pulled

Down

Vdd = 1.8 V. OE = GND, output is Weakly Pulled Down

Vdd = 2.5V, 2.8V or 3.3V, ST = GND, output is Weakly Pulled

Down

Vdd = 1.8 V. ST = GND, output is Weakly Pulled Down

25°C

Extended Commercial

Industrial

Supply voltages between 2.5V and 3.3V can be supported.

Contact

SiTime

for additional information.

Inclusive of Initial tolerance at 25 °C, and variations over

operating temperature, rated power supply voltage and load

Condition

Frequency Range

Frequency Stability and Aging

Operating Temperature Range

Supply Voltage and Current Consumption

LVCMOS Output Characteristics

Input Characteristics

Pin 1, OE or ST

Pin 1, OE logic high or logic low, or ST logic high

Pin 1, ST logic low

Note:

1. All electrical specifications in the above table are specified with 15 pF output load and for all Vdd(s) unless otherwise stated.

SiTime Corporation

Rev. 1.02

990 Almanor Avenue

Sunnyvale, CA 94085

(408) 328-4400

www.sitime.com

Revised June 24, 2013

Recommended Resources

Anti-theft alarm circuit

Cat meow simulator circuit one

Lingnan brand PDGZ-65, 30 fully automatic electronic drinking fountain circuit diagram

Temperature Stable Logarithmic Amplifier Circuit

Refrigerator thermostat alternative circuit

Computer motherboard circuit diagram 440GX_18

Newbie help, about 28027 wireless communication: I want to make a wireless communication function of 28027, and I need to use zigbee module and gsm module for wireless communication, but I don’t know which model of zigbee module and gsm module to ch...; Seviory Microcontroller MCU

Which chip is better for amplifying high-frequency signals?: Which chip is better for amplifying high-frequency signals around 40MHZ?...; 菲菲 Analog electronics

【Qinheng Trial】8. FlashROM: [i=s]This post was last edited by lising on 2019-7-16 17:28[/i]In this experiment, the specified data is written to the specified address of the Data Flash inside CH549, and the data is sent to the P2...; lising Domestic Chip Exchange

Learn Analog + Operational Amplifier Noise Optimization Handbook 5: [i=s]This post was last edited by dontium on 2015-1-23 11:46[/i] TINA installation: (1) Go to the Texas Instruments website and search for TINA [url]ti./[/url]Select [b]SPICE-Based Analog Simulation P...; huixianfxt Analogue and Mixed Signal

Protel DXP Guide.: Protel DXP Guide....; fighting PCB Design

The Agilent oscilloscope cannot be started and keeps stopping at the self-test position. What should I do?: The Agilent oscilloscope cannot be started and keeps stopping at the self-test position. What should I do?...; 0574119 Test/Measurement

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components