EEWORLDEEWORLDEEWORLD

Part Number

Search

TNPW120651R0BETY

Description
RES 51 OHM 0.1% 1/4W 1206
CategoryPassive components   
File Size136KB,8 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

TNPW120651R0BETY Overview

RES 51 OHM 0.1% 1/4W 1206

TNPW120651R0BETY Parametric

Parameter NameAttribute value
resistance51 Ohms
Tolerance±0.1%
Power (W)0.25W,1/4W
componentthin film
characteristic-
Temperature Coefficient±25ppm/°C
Operating temperature-55°C ~ 125°C
Package/casing1206 (3216 metric)
Supplier device packaging1206
size/dimensions0.126" long x 0.063" wide (3.20mm x 1.60mm)
Height - Installation (maximum)0.026"(0.65mm)
Number of terminals2
failure rate-
TNPW
www.vishay.com
Vishay
Lead (Pb)-Bearing High Stability Thin Film Chip Resistors
FEATURES
• Metal film layer on high quality ceramic
• SnPb termination plating, Pb content > 6 %
• Excellent overall stability at different environmental
conditions
0.05 % (1000 h rated power at 70 °C)
• Low temperature coefficient and tight tolerances (± 0.1 %;
± 10 ppm/K)
• Single lot date code available
APPLICATIONS
• Military
• Avionics
• Industrial
TNPW High Stability Thin Film Chip Resistors are the perfect
choice for most fields of modern electronics where lead
(Pb)-bearing terminations are mandatory and reliability and
stability are of major concern.
TECHNICAL SPECIFICATIONS
DESCRIPTION
Imperial size
Metric size code
Resistance range
Resistance tolerance
Temperature coefficient
Climatic category (LCT/UCT/days)
Rated dissipation,
P
70 (2)
Operating voltage,
U
max.
AC
RMS
or DC
Permissible film temperature,
F max.
Operating Temperature Range
Thermal resistance
(3)
Insulation voltage:
U
ins
1 min
Continuous
Failure rate: FIT
observed
75 V
75 V
100 V
75 V
200 V
75 V
0.3 x 10
-9
/h
300 V
75 V
300 V
75 V
870 K/W
550 K/W
55/125/56
0.063 W
50 V
TNPW0402
0402
RR1005M
10
to 100 k
TNPW0603
0603
RR1608M
10
to 332 k
TNPW0805
0805
RR2012M
10
to 1 M
± 1 %; ± 0.5 %; ± 0.1 %
± 50 ppm/K; ± 25 ppm/K; ± 15 ppm/K; ± 10 ppm/K
55/125/56
0.1 W
75 V
55/125/56
0.125 W
150 V
155 °C
-55 °C to 125 °C (155 °C)
440 K/W
220 K/W
170 K/W
55/125/56
0.25 W
200 V
55/125/56
0.33 W
200 V
TNPW1206
1206
RR3216M
10
to 2 M
TNPW1210
(1)
1210
RR3225M
10
to 3.01 M
Notes
(1)
The detail specification EN140401-801 does not cover this product size.
(2)
Rated voltage
P
x
R
. The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat
flow support of the printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature is not
exceeded.
(3)
Measuring conditions in accordance with EN 140401-801.
Revision: 24-Jan-14
Document Number: 31006
1
For technical questions, contact:
thinfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
Experts please help! ! I would like to ask about the problems encountered when porting ucosii to str71x
I'm porting cosii to str71x recently. I refer to other experts' porting examples, but I haven't succeeded. I always encounter problems when executing the msr cpsr_c, r0 instruction. After this sentenc...
qirick Real-time operating system RTOS
Ordered an MPLAB Snap
A few days ago, I needed an ATMEL programmer for an experiment, but found that the previous one was no longer usable. Since I don't use it very often, I wanted to find a low-cost programmer. I looked ...
dcexpert Microchip MCU
【AT-START-F403A Review】+FLASH reading and writing and image display
[i=s]This post was last edited by jinglixixi on 2020-10-24 13:12[/i]On the AT32F403A development board, in order to enhance the storage capacity, an auxiliary memory such as EN25QH128 is specially con...
jinglixixi Domestic Chip Exchange
How to place a logo on a PCB using AD14
I used AD10 to draw the board before. There was a thing called [color=#333333][backcolor=rgb(245, 245, 245)][font=Helvetica, Tahoma, Arial, sans-serif]PCB Logo Creator in the script, but this thing is...
zhoulei88 PCB Design
How to get system time
I have the following three questions: How to get the system time? How to get the alarm time? How to turn off the alarm? I read the RTC documentation but didn't understand anything. Please help....
fjfzpeggy Embedded System
The H-bridge drives the motor, but the driver chip always burns out. I use HIP4081A, but the pins 11 and 13 always burn out. Can you give me some advice? ? ?
, Pins 2.5.6.7 are the control terminals, and they always burn out the chip. Can someone help me solve this problem? ?...
永不言弃!!! Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2715  790  1929  2633  861  55  16  39  54  18 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号