EEWORLDEEWORLDEEWORLD

Part Number

Search

UM10-2466

Description
UM10-2466 SAFETY MAT 10M CABLE
CategoryTools and equipment   
File Size704KB,11 Pages
ManufacturerOMRON
Websitehttps://www.omron.com
Download Datasheet View All

UM10-2466 Overview

UM10-2466 SAFETY MAT 10M CABLE

Safety mats & Area guarding
Um Series
Universal Safety mat System
UM
Rev. 5.11
heavy-Duty four-Wire Presence Sensing mats
with integrated (non-removable) cable,
category 3 controllers, and Perimeter trim
System
• When UM series mats are combined with an MC3, MC4 or MC6
controller (with complete diagnostics), the result is a system
that meets the standard EN 1760-1:1998 and is entitled to
display the CE mark. See below for an overview of the various
components.
mat
• Activation force: 30 kg (66 lb.) per ANSI/RIA 15.06-1999,
ISO 13856-1:2001, ANSI B11.19-2003, and CSA Z432-04
• Conductive plates: 24 gauge galvanealed sheet steel
• Contact yield strength in excess of 20,000 lb./sq. in.; Fork lift
traffic of 12,000 lb.
• Mat housing cross section: 13.5 mm (0.54 in.)
• PVC black or yellow covering materials (other colors available
on request)
• Durometer of 80 (±3) shore A
• Single-piece molded construction
• Mat flammability self extinguishing, meets UL94VO
• IP67 rated
• Operating temperature -37 to 66°C (-35 to 150°F)
• Mat cable: 18-gauge, 4-conductor, 16-strand, 300 VAC
• Cable length: Standard 5 m (16 ft.), Optional 10 m (32 ft.)
controllers
• Safety category 3 device
• DIN-rail mount (MC3)
• NEMA controllers (MC4, MC6)
• 24 VDC or with universal power supply 100 to 240 VAC
trim
• Two-part perimeter and joining trim simplifies installation and
provides a custom appearance
• Aluminum base surrounds mat, the safety yellow PVC cover
secures mat in place, an aluminum cover that is installed in
place of the PVC cover is also available
• Two-part active joining trim joins multiple mats together
• Molded inside and outside corners available as an option
f
r
C
US
Description
An Omron STI Universal Mat system (UM series mat combined
with an MC3, MC4 or MC6) offers a simple method for guarding
personnel around hazardous machines. A Universal Mat system
offers freedom, flexibility, and reduced operator fatigue when
compared with traditional guarding methods such as interlocked
fences, pullback restraints or perimeter barriers.
Full visibility of and access to the work area is maintained. There
is no need to worry about personnel forgetting to replace mechani-
cal barriers or close gates.
how the System Works
The operation of a Universal Mat system is easy to understand.
The mat is a simple, normally open switch. When a specified
minimum weight is applied to the mat the "switch" closes. This
sends a signal to the controller which, in turn, sends a stop signal
to the guarded machine.
Each mat presents four wires to the controller. This provides the
redundancy required to monitor the wiring for open circuits due to
incorrect wiring or physical damage to the wires.
In order to meet many national safety regulations, Omron STI
offers trim to secure the mat to the floor so that it cannot be easily
relocated and therefore become ineffective.
f2
OmrOn Scientific technOlOgieS, inc.
USA
Tel. 1/888/510-4357
canada
Tel. 1/866/986-6766
For the Latest Information
On the Internet:
www.sti.com
LTE TURBO Coding Documentation
Documentation for LTE TURBO coding is urgently needed...
carsonsheng Download Centre
stc89c51 drives transistor as switch circuit
I used the IO of stc89c51 to generate a square wave with a high level of 5v, a low level of 0V, and a duty cycle of 1kHZ and 80%, and then connected the IO to a transistor (as shown in the figure) to ...
rainnnn Analog electronics
How should I modify the SDHC driver in the BSP to support multiple SD devices? Please give me some ideas.
The existing BSP only supports one SD card. (Question 1: Generally speaking, the CPU should be able to support multiple SD cards physically, and it should have relevant registers to indicate the numbe...
zlw Embedded System
How to modify the default value of protel99sePCB toolbar?
I am a beginner. When I draw a PCB board, the default values of the tools on the toolbar are all large. How can I make them smaller? Please help!...
Hxon PCB Design
Address bus programming problem
I am now going to write a program for the address bus of arm9 (YC2440) to achieve the function of transmitting data to another board. I wonder if anyone has done it before? Or is there any information...
nankeey Embedded System
XMC4800 Relax ECAT Kit Review 3 - Testing the EtherCAT Slave
[i=s]This post was last edited by tdatd on 2019-1-8 08:23[/i] After setting up the environment and lighting up the LED, we will go straight to our goal - ethercat communication. We will start the test...
tdatd Industrial Control Electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1816  1653  1738  88  55  37  34  35  2  26 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号