EEWORLDEEWORLDEEWORLD

Part Number

Search

BB26AV-FA

Description
SWITCH PUSH DPDT 0.4VA 28V
Categoryaccessories   
File Size267KB,6 Pages
ManufacturerNKK Switches
Environmental Compliance
Download Datasheet Parametric View All

BB26AV-FA Online Shopping

Suppliers Part Number Price MOQ In stock  
BB26AV-FA - - View Buy Now

BB26AV-FA Overview

SWITCH PUSH DPDT 0.4VA 28V

BB26AV-FA Parametric

Parameter NameAttribute value
typestandard
circuitDPDT
switch functionOn-on
Rated current0.4VA(AC/DC)
Rated voltage - AC28V
Rated voltage - DC28V
Actuator typecircle, button
Color - Actuator/Capblack
lighting type, color-
Lighting voltage (nominal)-
Installation typeThrough hole, right angle, vertical
Terminal typePC pin
Intrusion protection-
characteristicantistatic
Panel opening size-
Operating temperature-30°C ~ 85°C
Mechanical life25,000 cycles
Electrical life25,000 cycles
Series BB
Toggles
Process Sealed Subminiature Antistatic Pushbuttons
Rockers
General
Specifications
Electrical Capacity (Resistive Load)
Logic Level:
Pushbuttons
C
Other Ratings
Contact Resistance:
Insulation Resistance:
Dielectric Strength:
Mechanical Life:
Electrical Life:
Nominal Operating Force:
Contact Timing:
Travel:
0.4VA maximum @ 28V AC/DC maximum
(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Note: Find additional explanation of operating range in Supplement section.
Keylocks
50 milliohms maximum
500 megohms minimum @ 500V DC
500V AC minimum for 1 minute minimum
50,000 operations minimum (momentary)
25,000 operations minimum (alternate action)
50,000 operations minimum (momentary)
25,000 operations minimum (alternate action)
2.55N (momentary); 2.94N (alternate action)
Nonshorting
Momentary: Pretravel .028” (0.7mm); Overtravel .016” (0.4mm); Total Travel .043” (1.1mm)
Alternate: Pretravel .039” (1.0mm); Overtravel .039” (1.0mm); Total Travel .079” (2.0mm)
Programmable Illuminated PB
Materials & Finishes
Rotaries
Plunger:
Bushing:
Case Housing:
Support Bracket:
Movable Contact:
Stationary Contacts:
Terminals:
Polyacetal
Carbon blended polyamide
Glass fiber reinforced polyamide
Tin plated phosphor bronze
Phosphor bronze with gold plating
Copper alloy with gold plating
Copper alloy with gold plating
Slides
Tactiles
Environmental Data
Operating Temp Range:
Humidity:
Vibration:
Shock:
Tilt
–30°C through +85°C (–22°F through +185°F)
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
50G (490m/s
2
) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Installation
Touch
Cap Installation Force:
49.03N (11.2 lbf) maximum downward force on actuator;
actuator must be in UP position to remove cap from alternate action models
Indicators
PCB Processing
Soldering:
Cleaning:
Wave Soldering Recommended: See Profile A in Supplement section.
Manual Soldering: See Profile B in Supplement section.
Automated cleaning. See Cleaning specifications in Supplement section.
Accessories
Standards & Certifications
Flammability Standards:
Supplement
UL94V-0 available
The BB Series pushbuttons have not been tested for UL recognition or CSA certification.
These switches are designed for use in a low-voltage, low-current, logic-level circuit.
When used as intended in a logic-level circuit, the results do not produce hazardous energy.
C12
www.nkkswitches.com
How do I understand this sentence for? I don’t understand the idea!
#define LED pin led=[12,13,14,15,16,17,18,19] leds = [Pin(led[i], Pin.OUT) for i in range(0,8)]What I don't understand is why there is a statement on the left side of for. I have never seen this form ...
不爱吃鱼的猫 MicroPython Open Source section
Solution to network label error in Proteus
Problem description:In Proteus simulation, a network label error occursSolution:Modify the network label. For example, if the error message shows that the network label is D5, change the label D5 to P...
大一王 51mcu
MSP430 development board download problem!
I am using the MSP430G2 LaunchPad to run an example program on IAR to flash an LED. Everything works fine when debugging, but after exiting debugging, the flashing becomes extremely slow! Pressing RST...
punkl Microcontroller MCU
Why do most MCUs operate at 5V?
5V comes from TTL level, 5 is True, 0 is False, and then the PN node with lower voltage drop was used to derive the 3.3 level.12V and 24V come from car batteries. In the early years, passenger cars ha...
是酒窝啊 stm32/stm8
Brother and sister, please exchange E coins for E cards
The introduction on the forum seems to take a long time. I want to buy a mobile phone for my dad before I leave. I have some E coins in my account. Can anyone help me change them? 150. Thank you very ...
Solo_M Talking
How can wince5.0 receive Bluetooth headset key press messages?
I modified the code in C:\WINCE500\PRIVATE\WINCEOS\COMM\BLUETOOTH, but it still cannot be compiled even after full compilation. Is there any way to intercept the Bluetooth headset key press messages?...
liuzh Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1328  2345  569  479  2230  27  48  12  10  45 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号