simultaneous sampling 14-bit A/D converters designed
for digitizing high frequency, wide dynamic range signals.
They are perfect for demanding communications applica-
tions with AC performance that includes 73.1dB SNR and
90dB spurious free dynamic range (SFDR). Ultralow jitter
of 0.08ps
RMS
allows undersampling of IF frequencies with
excellent noise performance.
DC specs include ±1LSB INL (typ), ±0.3LSB DNL (typ)
and no missing codes over temperature. The transition
noise is 1.2LSB
RMS
.
The digital outputs can be either full rate CMOS, double
data rate CMOS, or double data rate LVDS. A separate
output power supply allows the CMOS output swing to
range from 1.2V to 1.8V.
The ENC
+
and ENC
–
inputs may be driven differentially
or single-ended with a sine wave, PECL, LVDS, TTL, or
CMOS inputs. An optional clock duty cycle stabilizer al-
lows high performance at full speed for a wide range of
clock duty cycles.
L,
LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear
Technology Corporation. All other trademarks are the property of their respective owners.
Two-Channel Simultaneously Sampling ADC
73.1dB SNR
90dB SFDR
Low Power: 189mW/149mW/113mW Total
95mW/75mW/57mW per Channel
Single 1.8V Supply
CMOS, DDR CMOS, or DDR LVDS Outputs
Selectable Input Ranges: 1V
P-P
to 2V
P-P
750MHz Full Power Bandwidth S/H
Optional Data Output Randomizer
Optional Clock Duty Cycle Stabilizer
Shutdown and Nap Modes
Serial SPI Port for Configuration
64-Pin (9mm × 9mm) QFN Package
APPLICATIONS
n
n
n
n
n
n
Communications
Cellular Base Stations
Software Defined Radios
Portable Medical Imaging
Multi-Channel Data Acquisition
Nondestructive Testing
TYPICAL APPLICATION
1.8V
V
DD
1.8V
OV
DD
64k Point 2-Tone FFT, f
IN
= 69MHz,
70MHz, –1dBFS, 125Msps
0
–10
AMPLITUDE (dBFS)
CH 1
ANALOG
INPUT
S/H
14-BIT
ADC CORE
D1_13
CMOS,
DDR CMOS
OR DDR LVDS
OUTPUTS
–20
–30
–40
–50
–60
–70
–80
D1_0
D2_13
CH 2
ANALOG
INPUT
S/H
14-BIT
ADC CORE
OUTPUT
DRIVERS
D2_0
–90
–100
–110
–120
0
10
20
30
40
FREQUENCY (MHz)
50
60
21454314 TA03b
125MHz
CLOCK
GND
CLOCK
CONTROL
21454314 TA01a
OGND
21454314fa
1
LTC2145-14/
LTC2144-14/LTC2143-14
ABSOLUTE MAXIMUM RATINGS
(Notes 1, 2)
Supply Voltages (V
DD
, OV
DD
) ....................... –0.3V to 2V
Analog Input Voltage (A
IN+
, A
IN–
,
PAR/SER, SENSE) (Note 3) .......... –0.3V to (V
DD
+ 0.2V)
Digital Input Voltage (ENC
+
, ENC
–
,
CS,
SDI, SCK) (Note 4) .................................... –0.3V to 3.9V
SDO (Note 4) ............................................ –0.3V to 3.9V
Digital Output Voltage ................ –0.3V to (OV
DD
+ 0.3V)
Operating Temperature Range
LTC2145C, LTC2144C, LTC2143C............. 0°C to 70°C
LTC2145I, LTC2144I, LTC2143I ............ –40°C to 85°C
Storage Temperature Range................... –65°C to 150°C
PIN CONFIGURATIONS
FULL RATE CMOS OUTPUT MODE
TOP VIEW
64 V
DD
63 SENSE
62 V
REF
61 SDO
60 OF1
59 OF2
58 D1_13
57 D1_12
56 D1_11
55 D1_10
54 D1_9
53 D1_8
52 D1_7
51 D1_6
50 D1_5
49 D1_4
DOUBLE DATA RATE CMOS OUTPUT MODE
TOP VIEW
64 V
DD
63 SENSE
62 V
REF
61 SDO
60 OF2_1
59 DNC
58 D1_12_13
57 DNC
56 D1_10_11
55 DNC
54 D1_8_9
53 DNC
52 D1_6_7
51 DNC
50 D1_4_5
49 DNC
48 D1_3
47 D1_2
46 D1_1
45 D1_0
44 DNC
43 DNC
42 OV
DD
41 OGND
40 CLKOUT
+
39 CLKOUT
–
38 D2_13
37 D2_12
36 D2_11
35 D2_10
34 D2_9
33 D2_8
V
DD
1
V
CM1
2
GND 3
A
IN1+
4
A
IN1–
5
GND 6
REFH 7
REFL 8
REFH 9
REFL 10
PAR/SER 11
A
IN2+
12
A
IN2–
13
GND 14
V
CM2
15
V
DD
16
65
GND
48 D1_2_3
47 DNC
46 D1_0_1
45 DNC
44 DNC
43 DNC
42 OV
DD
41 OGND
40 CLKOUT
+
39 CLKOUT
–
38 D2_12_13
37 DNC
36 D2_10_11
35 DNC
34 D2_8_9
33 DNC
UP PACKAGE
64-LEAD (9mm 9mm) PLASTIC QFN
T
JMAX
= 150°C,
θ
JA
= 20°C/W
EXPOSED PAD (PIN 65) IS GND, MUST BE SOLDERED TO PCB
V
DD
17
ENC
+
18
ENC
–
19
CS
20
SCK 21
SDI 22
DNC 23
DNC 24
DNC 25
D2_0_1 26
DNC 27
D2_2_3 28
DNC 29
D2_4_5 30
DNC 31
D2_6_7 32
V
DD
1
V
CM1
2
GND 3
A
IN1+
4
A
IN1–
5
GND 6
REFH 7
REFL 8
REFH 9
REFL 10
PAR/SER 11
A
IN2+
12
A
IN2–
13
GND 14
V
CM2
15
V
DD
16
65
GND
UP PACKAGE
64-LEAD (9mm 9mm) PLASTIC QFN
T
JMAX
= 150°C,
θ
JA
= 20°C/W
EXPOSED PAD (PIN 65) IS GND, MUST BE SOLDERED TO PCB
V
DD
17
ENC
+
18
ENC
–
19
CS
20
SCK 21
SDI 22
DNC 23
DNC 24
D2_0 25
D2_1 26
D2_2 27
D2_3 28
D2_4 29
D2_5 30
D2_6 31
D2_7 32
21454314fa
2
LTC2145-14/
LTC2144-14/LTC2143-14
PIN CONFIGURATIONS
DOUBLE DATA RATE LVDS OUTPUT MODE
TOP VIEW
64 V
DD
63 SENSE
62 V
REF
61 SDO
60 OF2_1
+
59 OF2_1
–
58 D1_12_13
+
57 D1_12_13
–
56 D1_10_11
+
55 D1_10_11
–
54 D1_8_9
+
53 D1_8_9
–
52 D1_6_7
+
51 D1_6_7
–
50 D1_4_5
+
49 D1_4_5
–
V
DD
1
V
CM1
2
GND 3
A
IN1+
4
A
IN1–
5
GND 6
REFH 7
REFL 8
REFH 9
REFL 10
PAR/SER 11
A
IN2+
12
A
IN2–
13
GND 14
V
CM2
15
V
DD
16
65
GND
48 D1_2_3
+
47 D1_2_3
–
46 D1_0_1
+
45 D1_0_1
–
44 DNC
43 DNC
42 OV
DD
41 OGND
40 CLKOUT
+
39 CLKOUT
–
38 D2_12_13
+
37 D2_12_13
–
36 D2_10_11
+
35 D2_10_11
–
34 D2_8_9
+
33 D2_8_9
–
T
JMAX
= 150°C,
θ
JA
= 20°C/W
EXPOSED PAD (PIN 65) IS GND, MUST BE SOLDERED TO PCB
ORDER INFORMATION
LEAD FREE FINISH
LTC2145CUP-14#PBF
LTC2145IUP-14#PBF
LTC2144CUP-14#PBF
LTC2144IUP-14#PBF
LTC2143CUP-14#PBF
LTC2143IUP-14#PBF
TAPE AND REEL
LTC2145CUP-14#TRPBF
LTC2145IUP-14#TRPBF
LTC2144CUP-14#TRPBF
LTC2144IUP-14#TRPBF
LTC2143CUP-14#TRPBF
LTC2143IUP-14#TRPBF
PART MARKING*
LTC2145UP-14
LTC2145UP-14
LTC2144UP-14
LTC2144UP-14
LTC2143UP-14
LTC2143UP-14
PACKAGE DESCRIPTION
64-Lead (9mm × 9mm) Plastic QFN
64-Lead (9mm × 9mm) Plastic QFN
64-Lead (9mm × 9mm) Plastic QFN
64-Lead (9mm × 9mm) Plastic QFN
64-Lead (9mm × 9mm) Plastic QFN
64-Lead (9mm × 9mm) Plastic QFN
TEMPERATURE RANGE
0°C to 70°C
–40°C to 85°C
0°C to 70°C
–40°C to 85°C
0°C to 70°C
–40°C to 85°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to:
http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to:
http://www.linear.com/tapeandreel/
V
DD
17
ENC
+
18
ENC
–
19
CS
20
SCK 21
SDI 22
DNC 23
DNC 24
D2_0_1
–
25
D2_0_1
+
26
D2_2_3
–
27
D2_2_3
+
28
D2_4_5
–
29
D2_4_5
+
30
D2_6_7
–
31
D2_6_7
+
32
UP PACKAGE
64-LEAD (9mm 9mm) PLASTIC QFN
21454314fa
3
LTC2145-14/
LTC2144-14/LTC2143-14
CONVERTER CHARACTERISTICS
The
l
denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C. (Note 5)
LTC2145-14
PARAMETER
Resolution (No Missing Codes)
Integral Linearity Error
Differential Linearity Error
Offset Error
Gain Error
Offset Drift
Full-Scale Drift
Gain Matching
Offset Matching
Transition Noise
Internal Reference
External Reference
Differential Analog Input
(Note 7)
Internal Reference
External Reference
CONDITIONS
l
LTC2144-14
MIN
14
–2.6
–0.9
–9
–1.5
TYP
±1
±0.3
±1.5
±1.5
–0.3
±10
±30
±10
±0.2
±1.5
1.28
MAX
2.6
0.9
9
1.1
14
LTC2143-14
MIN
–2.6
–0.8
–9
–1.5
TYP
±1
±0.3
±1.5
±1.5
–0.3
±10
±30
±10
±0.2
±1.5
1.20
MAX
2.6
0.8
9
1.1
UNITS
Bits
LSB
LSB
mV
%FS
%FS
μV/°C
ppm/°C
ppm/°C
%FS
mV
LSB
RMS
MIN
14
–2.6
–0.9
–9
–1.8
TYP
±1
±0.3
±1.5
±1.5
–0.4
±10
±30
±10
±0.2
±1.5
1.25
MAX
2.6
0.9
9
0.9
Differential Analog Input (Note 6)
l
l
l
l
The
l
denotes the specifications which apply over the full operating temperature range, otherwise
specifications are at T
A
= 25°C. (Note 5)
SYMBOL PARAMETER
V
IN
V
IN(CM)
V
SENSE
I
INCM
Analog Input Range (A
IN+
– A
IN–
)
Analog Input Common Mode (A
IN+
+ A
IN–
)/2
Analog Input Common Mode Current
CONDITIONS
1.7V < V
DD
< 1.9V
Differential Analog Input (Note 8)
Per Pin, 125Msps
Per Pin, 105Msps
Per Pin, 80Msps
0 < A
IN+
, A
IN–
< V
DD
0 < PAR/SER < V
DD
0.625 < SENSE < 1.3V
Single-Ended Encode
Differential Encode
Figure 6 Test Circuit
l
l
l
l
l
l
ANALOG INPUT
MIN
0.7
0.625
TYP
1 to 2
V
CM
1.250
155
130
100
MAX
1.25
1.300
UNITS
V
P-P
V
V
μA
μA
μA
External Voltage Reference Applied to SENSE External Reference Mode
I
IN1
I
IN2
I
IN3
t
AP
t
JITTER
CMRR
BW-3B
Analog Input Leakage Current (No Encode)
PAR/SER Input Leakage Current
SENSE Input Leakage Current
Sample-and-Hold Acquisition Delay Time
Sample-and-Hold Acquisition Delay Jitter
Analog Input Common Mode Rejection Ratio
Full-Power Bandwidth
–1.5
–3
–3
0
0.08
0.10
80
750
1.5
3
3
μA
μA
μA
ns
ps
RMS
ps
RMS
dB
MHz
21454314fa
4
LTC2145-14/
LTC2144-14/LTC2143-14
The
l
denotes the specifications which apply over the full operating temperature range,
otherwise specifications are at T
A
= 25°C. A
IN
= –1dBFS. (Note 5)
LTC2145-14
SYMBOL
SNR
PARAMETER
Signal-to-Noise Ratio
CONDITIONS
5MHz Input
70MHz Input
140MHz Input
l
DYNAMIC ACCURACY
LTC2144-14
MIN
71.2
TYP
72.9
72.8
72.4
90
89
84
90
89
84
95
95
95
72.8
72.6
72
–110
MAX
LTC2143-14
MIN
71.7
TYP
73.4
73.3
72.9
90
89
84
90
89
84
95
95
95
73.2
73.1
72.4
–110
MAX
UNITS
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
dBc
MIN
71.4
TYP
73.1
73
72.6
90
89
84
90
89
84
95
95
95
73
72.8
72.2
–110
MAX
SFDR
Spurious Free Dynamic Range 5MHz Input
2nd Harmonic
70MHz Input
140MHz Input
Spurious Free Dynamic Range 5MHz Input
3rd Harmonic
70MHz Input
140MHz Input
Spurious Free Dynamic Range 5MHz Input
4th Harmonic or Higher
70MHz Input
140MHz Input
l
76
77
78
l
79
79
81
l
86
86
86
S/(N+D)
Signal-to-Noise Plus
Distortion Ratio
Crosstalk
5MHz Input
70MHz Input
140MHz Input
10MHz Input
l
70.8
70.8
71.4
INTERNAL REFERENCE CHARACTERISTICS
PARAMETER
V
CM
Output Voltage
V
CM
Output Temperature Drift
V
CM
Output Resistance
V
REF
Output Voltage
V
REF
Output Temperature Drift
V
REF
Output Resistance
V
REF
Line Regulation
–400μA < I
OUT
< 1mA
1.7V < V
DD
< 1.9V
–600μA < I
OUT
< 1mA
I
OUT
= 0
CONDITIONS
I
OUT
= 0
The
l
denotes the specifications which apply over the
full operating temperature range, otherwise specifications are at T
When I first used a multimeter, my teacher told me that choosing the appropriate range would achieve the best accuracy.
For example, a multimeter has ranges of 1V, 5V, 10V, and 50V. The target voltage...
The Double 11 Shopping Festival is coming soon. At the request of relevant departments, I would like to share three short videos on how to prevent telecommunication fraud. I hope that the cases in the...
[size=4] Transient interference of voltage and current is the main cause of damage to electronic circuits and equipment, often causing immeasurable losses to people. These interferences usually come f...
Can anyone help me design a multi-channel function generator? It requires seven signal outputs, signal amplification, voltage and current conversion, display function and delay control. Thank you. If ...
I used Vivado to build the Microblaze hardware platform, and then used SDK to program the button control LED function. After debugging and running, it can be realized. But after burning it into Flash,...
On August 23rd, Geely's subsidiary, Jiyao Tongxing, announced it has the industry's largest advanced production capacity for tandao
batteries
, with eight production bases across China. Jiy...[Details]
When you are happily watching NBA or football, your wife asks you to turn off the lights in the bedroom. Would you be depressed? Of course, unless you are not afraid of your wife.
Now you are ...[Details]
For healthcare professionals, accurate diagnosis and treatment are crucial for a clear picture of a person's health. However, healthcare professionals often rely on tests at medical facilities, cli...[Details]
Gross profit margin jumped from 13.6% in the first half of last year to 25.9%, almost doubling year-on-year.
On August 21, RoboSense released its interim performance report, in which the...[Details]
For autonomous vehicles to safely navigate the road, they must identify far more complex objects than just traffic lights, pedestrians, and other familiar objects. Among these obstacles is a crucia...[Details]
On August 22, South Korean media Nate reported on the 20th local time that Samsung Electronics is introducing Hyper Cell technology into its most advanced 2nm process technology, striving to improv...[Details]
PowiGaN achieves 95% efficiency at both light and full loads, meeting critical operational and safety requirements.
DARWIN, Australia and SAN JOSE, Calif.,
August 22, 2025 – Powe...[Details]
Tires are a very important component for cars. They are related to the driving experience of the vehicle. We are almost inseparable from cars in our daily lives. For tires, according to the role of...[Details]
The fracture mechanism is stress concentration, which typically occurs at the capacitor lead pins or pad connection points, as shown in the figure. Under vibration, the capacitor lead pins and pad ...[Details]
Batteries are a core component of new energy vehicles, accounting for over 40% of the total cost. This is also the area where automakers are most willing to tamper with costs. Since 2021, domestic ...[Details]
With the growth of the Internet of Things (IoT), wearable, and portable devices, consumers are growing weary of cluttered cables and the need for frequent battery recharges. The benefits of wireles...[Details]
Introduction: Traditionally, lead-acid batteries have primarily been used to provide backup power and power regulation based on location. In typical applications, the battery's actual use (discharg...[Details]
For the average person, an electricity meter is a monthly bill. For beginners, it's a collection of components and parts. For experienced meter engineers, however, it's a complex and complex proces...[Details]
As automotive technology develops at an ever-increasing pace, the performance requirements for automotive internal structures, components, and accessories are becoming increasingly demanding. The d...[Details]
This article uses the Allwinner T507 quad-core automotive-grade processor as the development board. This article explains how to configure Ethernet for the T507 development board. Other boards may ...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
