and a 6-bit (64-step) ±50% correction register. All controls
are programmable via a simple serial data interface. Three
banks of 16-channels each can be configured such that
they operate 120° out-of-phase with each other.
The LT8500 features two diagnostic information flags:
synchronization error and open LED. The flags are sent,
with additional state information, on the serial data interface
during status read back. The 50MHz cascadable serial data
interface includes buffering and skew-balancing, making
the chip suitable for PWM intensive applications such
as large screen LCD dynamic backlighting and mono-,
multi- and full-color LED displays. The LT8500 is also
ideally suited to control three LT3595A LED drivers.
L,
LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear
Technology Corporation. All other trademarks are the property of their respective owners.
n
n
n
n
n
3V to 5.5V Input Voltage
48 Independent PWM Outputs
TTL/CMOS Logic 50MHz Serial Data Interface
12-Bit (4096 Steps) PWM Width Resolution
6-Bit (64 Steps) PWM Correction
(±50% of Programmed PWM Width)
Up to 6.1kHz PWM Frequency (PWMCK = 25MHz)
Phase-Shift Option Reduces Switching Noise
Directly Controls Three LT3595A 16-Channel
LED Drivers
Diagnostic Information: Sync Error/Open LED Flags
56-Pin (6mm
×
6mm
×
0.78mm) TLA QFN Package
applicaTions
n
n
n
n
n
n
n
Large Screen Display LED Backlighting
Mono-, Multi-, Full-Color LED Displays
LED Billboards and Signboards
Motor Control
Industrial Control
Automated Test Equipment
Robotics
Typical applicaTion
48 PWM OUTPUTS
• • • • •
5-WIRE
SERIAL
DATA
INTERFACE
OSC
PWM[48:1]
SDI
SDO
SCKI
SCK0
LDIBLANK
LT8500 (1)
PWMCK
OPENLED
48 PWM OUTPUTS
• • • • •
PWM[48:1]
SDI
SDO
SCKI
SCK0
LDIBLANK
LT8500 (2)
PWMCK
OPENLED
••••
••••
48 PWM OUTPUTS
• • • • •
PWM[48:1]
SDI
SDO
SCKI
SCK0
LDIBLANK
LT8500 (N)
PWMCK
OPENLED
DIAGNOSTIC
CIRCUIT
••••
••••
••••
8500 TA01a
8500fb
For more information
www.linear.com/LT8500
1
LT8500
absoluTe MaxiMuM raTings
(Note 1)
V
CC
............................................................... –0.3V to 6V
SDI, SCKI, PWMCK,
OPENLED,
LDIBLANK ......... –0.3V to Lesser of 6V and (V
CC
+ 0.3V)
Operating Junction Temperature Range
(Note 2).................................................. –40°C to 125°C
Storage Temperature Range .................. –65°C to 150°C
pin conFiguraTion
TOP VIEW
PWM13
PWM14
PWM15
PWM16
PWM10
PWM47
PWM11
46 PWM12
45 PWM5
44 PWM6
43 PWM7
42 PWM8
41 LDIBLANK
40 SDI
39 PWMCK
57
GND
38 SCKO
37 VCC
36 SCKI
35 SDO
34
OPENLED
33 PWM33
32 PWM34
31 PWM35
30 PWM36
29 PWM45
19 20 21 22 23 24 25 26 27 28
PWM39
PWM38
PWM37
PWM44
PWM43
PWM42
PWM41
PWM48
PWM46
PWM2
PWM3
PWM4
PWM9
TOP VIEW
PWM915
PWM13
PWM14
PWM16
PWM10
PWM11
PWM3
PWM4
PWM9
PWM1 1
PWM24 2
PWM23 3
PWM12
PWM5
PWM8
SDI
SDKO
SCKI
OPENLED
PWM35
PWM45
PWM7
PWM6
LDIBLANK
PWMCK
V
CC
SDO
PWM33
PWM34
PWM36
PWM46
PWM22 4
PWM21 5
PWM28 6
PWM27 7
PWM26 8
PWM25 9
PWM32 10
PWM31 11
PWM30 12
PWM29 13
PWM20 14
PWM19 15
PWM18 16
PWM17 17
PWM40 18
A30
A29
A28
A27
A26
A25
A24
A23
A22
56 55 54 53 52 51 50 49 48 47
PWM2
PWM24
PWM22
PWM23
PWM26
PWM25
PWM31
PWM20
PWM29
PWM17
PWM40
PWM1
PWM21
PWM27
PWM28
PWM32
PWM30
PWM19
PWM18
A1 A40 A39 A38 A37 A36 A35 A34 A33 A32 A31
A2
A3
A4
A5
A6
A7
A8
A9
A10
B1
B2
B3
B4
B5
B6
B7
B8
57
GND
B16
B15
B14
B13
B12
B11
B10
B9
A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 A21
PWM39
PWM37
PWM38
PWM44
PWM43
PWM42
PWM41
PWM48
PWM47
TJ PACKAGE
56-LEAD PLASTIC TLA QFN (6mm × 6mm)
T
JMAX
= 125°C,
θ
JA
= 35°C/W,
θ
JC
= 5°C/W
EXPOSED PAD (PIN 57) IS GND, MUST BE SOLDERED TO PCB
UHH PACKAGE
56-LEAD (5mm × 9mm) PLASTIC QFN
T
JMAX
= 125°C,
θ
JA
= 35°C/W,
θ
JC
= 5°C/W
EXPOSED PAD (PIN 57) IS GND, MUST BE SOLDERED TO PCB
(NOT RECOMMENDED FOR NEW DESIGNS)
orDer inForMaTion
LEAD FREE FINISH
LT8500EUHH#PBF
LT8500IUHH#PBF
LT8500ETJ#PBF
LT8500ITJ#PBF
TAPE AND REEL
LT8500EUHH#TRPBF
LT8500IUHH#TRPBF
LT8500ETJ#TRPBF
LT8500ITJ#TRPBF
http://www.linear.com/product/LT8500#orderinfo
PART MARKING*
8500
8500
LT8500TJ
LT8500TJ
PACKAGE DESCRIPTION
56-Lead (5mm
×
9mm) Plastic QFN
56-Lead (5mm
×
9mm) Plastic QFN
56-Lead (6mm
×
6mm) Plastic TLAQFN
56-Lead (6mm
×
6mm) Plastic TLAQFN
TEMPERATURE RANGE
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
For more information on lead free part marking, go to:
http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to:
http://www.linear.com/tapeandreel/.
Some packages are available in 500 unit reels through
designated sales channels with #TRMPBF suffix.
8500fb
2
For more information
www.linear.com/LT8500
LT8500
elecTrical characTerisTics
SYMBOL
Supply
V
CC
V
CC
Operating Voltage
Input Logic Levels
High Level Voltage
Low Level Voltage
Input Current
OPENLED
Pull-Up Resistor
Input Capacitance (Note 4)
SDO, SCKO Output Voltages
High Level Voltage
Low Level Voltage
PWM [48:1] Output Voltages
High Level Voltage
Low Level Voltage
l
The
l
denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C. V
CC
= 3.3V, unless otherwise noted.
PARAMETER
CONDITIONS
MIN
3.0
TYP
MAX
5.5
UNIT
V
Digital Inputs: SCKI, SDI, LDIBLANK,
OPENLED,
PWMCK
V
IH
V
IL
I
IN
R
PU
C
IN
V
CC
= 5V
V
CC
= 3.3V
V
CC
= 5V
V
CC
= 3.3V
Pin Voltage = V
CC
or GND Excluding
OPENLED
V
CC
= 5.5V
Pin to GND
l
l
l
l
4.0
2.7
1.0
0.6
1
100
3
130
V
V
V
V
µA
kΩ
pF
–1
70
Digital Outputs: SCKO, SDO, PWM[48:1]
V
OH
V
OL
V
OH
V
OL
I
OUT
= –6mA, V
CC
= 5V
I
OUT
= –3mA, V
CC
= 3.3V
I
OUT
= 6mA, V
CC
= 5V
I
OUT
= 3mA, V
CC
= 3.3V
I
OUT
= –3mA, V
CC
= 5V
I
OUT
= –1.5mA, V
CC
= 3.3V
I
OUT
= 3mA, V
CC
= 5V
I
OUT
= 1.5mA, V
CC
= 3.3V
l
l
l
l
l
l
l
l
4.0
2.7
1.0
0.6
V
V
V
V
V
V
V
V
4.0
2.7
1.0
0.6
The
l
denotes the specifications which apply over the full operating temperature
range, otherwise specifications are at T
A
= 25°C. V
CC
= 3.3V, and all inputs are rail-to-rail unless otherwise noted.
SYMBOL
f
SCKI
f
PWMCK
t
WH-SCKI
t
WL-SCKI
t
WH-LDI
t
WH-BLANK
t
SU-SDI
t
HD-SDI
t
SU-LDI
t
HD-LDI
t
PD-SDO
t
PD-SCK
t
HD-SDO
t
DC-SCK
PARAMETER
Data Shift Clock Frequency
PWMCK Clock Frequency
Minimum SCKI High Time (Note 3)
Minimum SCKI Low Time (Note 3)
LDIBLANK Pulse Duration
(LDI Function)
LDIBLANK Pulse Duration
(BLANK Function)
SDI-SCKI Setup Time (Note 3)
SCKI-SDI Hold Time (Note 3)
SCKI-LDIBLANK Setup Time (Note 3)
LDIBLANK-SCKI Hold Time (Note 3)
SCKI-SDO Propagation Delay (Note 3)
SCKI-SCKO Propagation Delay (Note 3)
SCKO-SDO Hold Time (Note 3)
SCKI-SCKO Duty Cycle Change (Note 4)
CONDITIONS
SCKI
↑
– SCKI
↑
(Figure 4)
PWMCK
↑
– PWMCK
↑
(Figure 5)
SCKI = High
SCKI = Low
LDIBLANK = High (Figure 4)
LDIBLANK = High (Figure 4)
SDI
↑↓
– SCKI
↑
(Figure 4)
SCKI
↑
– SDI
↑↓
(Figure 4)
SCKI
↑
– LDIBLANK
↑
(Figure 4)
SCKI 50% Duty Cycle
LDIBLANK
↓
– SCKI
↑
(Figure 4)
SCKI
↑
– SDO
↑↓
(Figure 4)
SCKI
↑
– SCKO
↑
(Figure 4)
SCKO
↑
– SDO
↑↓
(Figure 4)
Difference Between SCKI = High Time
and SCKO = High Time, C
LOAD
= 25pF
l
l
l
l
l
l
l
l
l
l
l
TiMing characTerisTics
MIN
TYP
MAX
50
25
UNIT
MHz
MHz
ns
ns
2
2
8
50,000
3
1.75
10
5
15
10
2.75
–0.2
25
20
5,000
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
8500fb
For more information
www.linear.com/LT8500
3
LT8500
TiMing characTerisTics
SYMBOL
t
PD-PWM
t
R-SDO
t
F-SDO
t
R-PWM
t
F-PWM
PARAMETER
PWMCK-PWM[48:1] Propagation Delay
(Note 3)
SDO, SCKO Rise Time (Note 4)
SDO, SCKO Fall Time (Note 4)
PWM[48:1] Rise Time (Note 4)
PWM[48:1] Fall Time (Note 4)
The
l
denotes the specifications which apply over the full operating temperature
range, otherwise specifications are at T
A
= 25°C. V
CC
= 3.3V, and all inputs are rail-to-rail unless otherwise noted.
CONDITIONS
PWMCK
↑
– PWM
↑↓
(Figure 5)
C
LOAD
= 25pF 30% to 70%
,
C
LOAD
= 25pF 70% to 30%
,
C
LOAD
= 25pF 30% to 70%
,
C
LOAD
= 25pF 70% to 30%
,
l
MIN
TYP
32
2
2
12
12
MAX
50
UNIT
ns
ns
ns
ns
ns
Note 1:
Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2:
The LT8500E is guaranteed to meet performance specifications
from 0°C to 125°C junction temperature. Specifications over the –40°C
to 125°C operating junction temperature range are assured by design,
characterization and correlation with statistical process controls. The
LT8500I is guaranteed over the full –40°C to 125°C operating junction
temperature range.
Note 3:
Propagation delays, setup/hold times and hi times are measured
from 50% to 50%.
Note 4:
This parameter is correlated to lab measurements and is not
subject to production testing.
TiMing DiagraM
t
WH-LDI
t
SU-SDI
t
HD-SDI
1/f
SCKI
t
SU-LDI
t
HD-LDI
t
WH-SCKI
t
WL-SCKI
SCKI
SDI
LDIBLANK
SCKO
SDO
8500 TD01
t
PD-SDO
t
PD-SCK
t
HD-SDO
8500fb
4
For more information
www.linear.com/LT8500
LT8500
For the I
CC
vs V
CC
Graphs, the Following Conditions
Apply: 23pF Load on SCKO. PWM Outputs Enabled: Duty Cycle = 1365/4096, 10pF Average Load on PWMs.
LT8500 - 48-Channel LED PWM Generator with 12-Bit Resolution and 50MHz Cascadable Serial Interface; Package: QFN; Pins: 56; Temperature Range: -40°C to 85°C
IC PWM GENERATOR 56-QFN
IC PWM GENERATOR 56-QFN
IC PWM GENERATOR 56-TLAQFN
IC PWM GENERATOR 56-TLAQFN
100V Current Mode Synchronous Switching Regulator Controller
[if gte mso 9]>1024x768Normal07.8 磅02falsefalsefalseBasic theory and design skills of digital circuit FPGASimilarities and differences between A , C and Verilog (the key lies in the differences, and t...
Dear experts, I would like to ask you, I want to make a three-wire serial line, how should I do it? What materials and equipment do I need? I looked at the information, but I have no idea what a three...
This migration guide describes the hardware and software differences to be aware of when migrating between the F28004x and F28002x C2000 MCUs. This document provides block diagrams of the two MCUs to ...
When a control system is exposed to high levels of electronic noise, its reliability will be reduced, but this effect can be minimized by using proper power and grounding methods. Various components i...
introduction
With the continuous optimization of surface mount technology (SMT) and the rapid development of chip component manufacturing technology, the application of chip mounters in the el...[Details]
As a wireless broadband metropolitan area network standard, WiMAX technology has greater advantages than previous 3.5GHz MMDS products in terms of non-line-of-sight transmission and spectrum utiliz...[Details]
1. Introduction
Automobile pollution is one of the most important issues that people are most concerned about and need to solve urgently. As an important method for detecting automobile exhau...[Details]
The Portable Digital Data Acquisition System (PDDAS) uses LabVIEW Real-Time and PXI to control the wind tunnel test and record air pressure data from 128 different channels.
"The LabVIEW Real-...[Details]
introduction
For the voltage regulator modules (VRMs) that power the latest computer central processing units (CPUs), power supply designers have historically used multiphase interleaved b...[Details]
My colleague and I spent the day chatting in the hotel bar. We had met with several customers. We were both wondering how come these engineers we were meeting knew almost nothing about analog techn...[Details]
1. Principle of displacement angle sensor
The angle sensor is used to detect angles. It has a hole in its body that fits the LEGO axle. When connected to the RCX, the angle sensor counts once ...[Details]
1. Overview
The Virtual CAN Interface (VCI) function library is an application program interface specifically provided for the use of ZLGCAN devices on PCs. The functions in the library ar...[Details]
1. Project Introduction
Shandong Dezhou Xingtai Paper Co., Ltd. is a newly built high-end paperboard production enterprise with domestic leading level established by Shandong Zhaodongfang Pape...[Details]
In the analysis of electronic circuits, static analysis (also known as DC analysis) is the basis of circuit analysis. However, it is well known that electronic components are nonlinear, so the anal...[Details]
RS-422 and RS-485 are both serial data interface standards, which were developed and published by the Electronic Industries Association (EIA). RS-422 defines a balanced communication interface with a ...[Details]
12v Lead Acid batteries used in trucks, cars, RVs and uninterruptible power supplies are usually rated at 12V. This circuit monitors the battery, the charge and discharge curves, gives the cu...[Details]
The concept of state machine
State machine is an important concept in software programming. More important than this concept is its flexible application. In a clear and efficient program, ther...[Details]
In today's body control module (BCM) designs, savvy engineers are moving away from electromechanical relays whenever possible. Their next step is to eliminate fuses. But is eliminating fuses a nece...[Details]
Describe how to meet the challenges of complexity with a modern wiring design toolset. Option codes and expressions can simulate the variables of an automotive project. A full-featured tool suite c...[Details]
ADI Reference Circuit
京公网安备 11010802033920号
EEWORLD
