Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
For more information on lead free part marking, go to:
http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to:
http://www.linear.com/tapeandreel/
†
This product is only offered in trays. For more information go to:
http://www.linear.com/packaging/
available options
OUTPUT VOLTAGE
1.250
2.048
2.500
INITIAL ACCURACY
0.05%
0.1%
0.05%
0.1%
0.05%
0.1%
0.05%
0.1%
0.05%
0.1%
0.05%
0.1%
0.05%
0.1%
0.05%
0.1%
0.05%
0.1%
0.05%
0.1%
TEMPERATURE COEFFICIENT
5ppm/°C
10ppm/°C
5ppm/°C
10ppm/°C
5ppm/°C
10ppm/°C
5ppm/°C
8ppm/°C
5ppm/°C
10ppm/°C
5ppm/°C
10ppm/°C
5ppm/°C
10ppm/°C
5ppm/°C
8ppm/°C
5ppm/°C
10ppm/°C
5ppm/°C
8ppm/°C
PART NUMBER**
LTC6652AHMS8-1.25
LTC6652BHMS8-1.25
LTC6652AHMS8-2.048
LTC6652BHMS8-2.048
LTC6652AHMS8-2.5
LTC6652BHMS8-2.5
LTC6652AHLS8-2.5
LTC6652BHLS8-2.5
LTC6652AHMS8-3
LTC6652BHMS8-3
LTC6652AHMS8-3.3
LTC6652BHMS8-3.3
LTC6652AHMS8-4.096
LTC6652BHMS8-4.096
LTC6652AHLS8-4.096
LTC6652BHLS8-4.096
LTC6652AHMS8-5
LTC6652BHMS8-5
LTC6652AHLS8-5
LTC6652BHLS8-5
3.000
3.300
4.096
5.000
**See Order Information section for complete part number listing.
The
l
denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C, V
IN
= V
OUT
+ 0.5V, unless otherwise noted.
PARAMETER
Output Voltage
Output Voltage Temperature Coefficient
(Note 3)
Line Regulation
CONDITIONS
LTC6652A
LTC6652B
LTC6652A
LTC6652BMS8
LTC6652BLS8
V
OUT
+ 0.5V ≤ V
IN
≤ 13.2V,
SHDN
= V
IN
l
l
l
l
electrical characteristics
MIN
–0.05
–0.1
TYP
MAX
0.05
0.1
UNITS
%
%
ppm/°C
ppm/°C
ppm/°C
ppm/V
ppm/V
6652fg
2
4
4
2
5
10
8
50
80
For more information
www.linear.com/LTC6652
3
LTC6652
The
l
denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C, V
IN
= V
OUT
+ 0.5V, unless otherwise noted.
PARAMETER
Load Regulation (Note 4)
CONDITIONS
I
SOURCE
= 5mA, LTC6652-1.25, LTC6652-2.048,
LTC6652-2.5, LTC6652-3, LTC6652-3.3,
LTC6652-4.096, LTC6652-5
I
SINK
= 1mA, LTC6652-1.25, LTC6652-2.048
I
SINK
= 5mA, LTC6652-2.5, LTC6652-3,
LTC6652-3.3, LTC6652-4.096, LTC6652-5
Minimum Operating Voltage (Note 5)
I
SOURCE
= 5mA, V
OUT
Error ≤ 0.1%
LTC6652-1.25, LTC6652-2.048
LTC6652-2.5, LTC6652-3, LTC6652-3.3,
LTC6652-4.096, LTC6652-5
Short V
OUT
to GND
Short V
OUT
to V
IN
Logic High Input Voltage
Logic High Input Current
Logic Low Input Voltage
Logic Low Input Current
Supply Current
Shutdown Current
Output Voltage Noise (Note 6)
No Load
l
l
l
l
l
l
electrical characteristics
MIN
TYP
20
80
MAX
75
200
250
600
150
450
UNITS
ppm/mA
ppm/mA
ppm/mA
ppm/mA
ppm/mA
ppm/mA
V
V
l
50
l
l
l
2.7
V
OUT
+ 0.3V
16
16
2
0.1
0.1
350
1
0.8
1
560
2
Output Short-Circuit Current
Shutdown Pin (SHDN)
mA
mA
V
µA
V
µA
µA
µA
µA
ppm
P-P
ppm
P-P
ppm
P-P
ppm
P-P
ppm
P-P
ppm
RMS
µs
ppm/√kHr
ppm/√kHr
ppm
ppm
ppm
ppm
ppm
ppm
SHDN
Tied to GND
0.1Hz ≤ f ≤ 10Hz
LTC6652-1.25
LTC6652-2.048, LTC6652-2.5, LTC6652-3
LTC6652-3.3
LTC6652-4.096
LTC6652-5
10Hz ≤ f ≤ 1kHz
0.1% Settling, C
LOAD
= 0
l
0.1
2.4
2.1
2.2
2.3
2.8
3
100
60
20
80
75
45
45
25
10
Turn-On Time
Long-Term Drift of Output Voltage (Note 7) LTC6652MS8
LTC6652LS8
Hysteresis (Note 8)
∆T = –40°C to 125°C, LTC6652MS8
∆T = –40°C to 85°C, LTC6652MS8
∆T = 0°C to 70°C, LTC6652MS8
∆T = –40°C to 125°C, LTC6652LS8
∆T = –40°C to 85°C, LTC6652LS8
∆T = 0°C to 70°C, LTC6652LS8
Note 1:
Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2:
If the parts are stored outside of the specified temperature range,
the output may shift due to hysteresis.
Note 3:
Temperature coefficient is measured by dividing the maximum
change in output voltage by the specified temperature range.
Note 4:
Load regulation is measured on a pulse basis from no load to the
specified load current. Output changes due to die temperature change
must be taken into account separately.
Note 5:
Excludes load regulation errors.
Note 6:
Peak-to-peak noise is measured with a 3-pole highpass at 0.1Hz
and 4-pole lowpass filter at 10Hz. The unit is enclosed in a still-air
environment to eliminate thermocouple effects on the leads. The test
time is 10 seconds. RMS noise is measured on a spectrum analyzer in
a shielded environment where the intrinsic noise of the instrument is
removed to determine the actual noise of the device.
Note 7:
Long-term stability typically has a logarithmic characteristic and
therefore, changes after 1000 hours tend to be much smaller than before that
time. Total drift in the second thousand hours is normally less than one third
that of the first thousand hours with a continuing trend toward reduced drift
with time. Long-term stability will also be affected by differential stresses
between the IC and the board material created during board assembly.
Note 8:
Hysteresis in output voltage is created by package stress that
differs depending on whether the IC was previously at a higher or lower
temperature. Output voltage is always measured at 25°C, but the IC is
cycled to the hot or cold temperature limit before successive measurements.
Hysteresis is roughly proportional to the square of the temperature change.
For instruments that are stored at well controlled temperatures (within 20
or 30 degrees of operational temperature) it’s usually not a dominant error
source.Typical hysteresis is the worst-case of 25°C to cold to 25°C or 25°C
to hot to 25°C, preconditioned by one thermal cycle.
Note 9:
The stated temperature is typical for soldering of the leads during
manual rework. For detailed IR reflow recommendations, refer to the
Applications section.
6652fg
4
For more information
www.linear.com/LTC6652
LTC6652
Characteristic curves are similar for most
LTC6652s. Curves from the LTC6652-1.25, LTC6652-2.5 and the LTC6652-5 represent the extremes and typical of the voltage options.
Characteristic curves for other output voltages fall between these curves and can be estimated based on their output.
What is ultrasound? What are the characteristics of ultrasound? It is very useful. You may not know it yet. In fact, it has nothing to do with our topic, but I still want to share it with you!...
DirectIO: The SRIO DirectIO transfer class is similar to a memcopy transfer between two SRIO devices. One of the devices is the master that initiates the transfer. The second device is the slave that ...
[i=s]This post was last edited by Tianyahaijiaosr on 2016-12-17 12:53[/i] My PCB contains four main components: microcontroller, serial touch screen, ADC, and op amp, all of which are powered by the s...
A new week has begun. With the release of our uS v0.1, the next thing we are going to implement is the communication console component I planned. Here is a brief explanation. Console, this name imitat...
1. Project Overview
1.1 Introduction
Currently, most music files are saved in MP3 format, a lossy audio compression format that cannot perfectly reproduce the original music. With the exp...[Details]
The most significant feature of IPS panels is that both electrodes are located on the same surface, unlike other LCD panels, which have electrodes arranged on top and bottom surfaces in a three-dim...[Details]
Amidst the wave of intelligent automotive transformation, advanced driver assistance is gradually emerging from cutting-edge technology into the mainstream, becoming a new frontier of industry comp...[Details]
introduction
As “energy conservation and emission reduction” has become an indicator of the National Economic Development Outline of the 11th Five-Year Plan, people’s awareness of green enviro...[Details]
In the scorching summer, electric fans are a must-have for cooling down people's homes. However, I believe most people have encountered this situation: the fan is plugged in, the switch is pressed,...[Details]
Charging is a familiar process for new energy vehicles, and as a source of battery energy, charging piles are crucial. New energy vehicle charging can be divided into fast charging and slow chargin...[Details]
Based on the commutation technology, thyristor rectifiers are classified into two main types. Line-commutated and force-commutated inverters are commonly used, while other commutated inverters, nam...[Details]
Reflow soldering is one of the most commonly used methods in electronics manufacturing, allowing for the soldering of large numbers of components in a relatively short time. However, any experience...[Details]
During daily operation of an R-type power transformer, the voltage used varies as the equipment being used adjusts. This raises the question: can the transformer change voltage at this point? The a...[Details]
The difference between a series inverter and a parallel inverter is that they use different oscillation circuits. A series inverter connects L, R, and C in series, while a parallel inverter connect...[Details]
Tires are a very important component for cars. They are related to the driving experience of the vehicle. We are almost inseparable from cars in our daily lives. For tires, according to the role of...[Details]
"I want to ask why there are so many manufacturers making mobile phone CPUs, but only Intel and AMD make computer CPUs?"
The progress of domestic PC CPU production has disappointed many ...[Details]
1. Introduction
In 2015, Apple's new MacBook and Apple Watch both featured force-sensing technology, which Apple calls Force Touch. Each time a user presses the touchpad, the device not only p...[Details]
On August 20, Huawei Device announced that the all-new M7 is the first to feature an in-cabin laser vision solution. This solution offers enhanced active safety capabilities compared to primary vis...[Details]
Silicon Labs (also known as "Silicon Labs"), an innovative leader in low-power wireless connectivity, will showcase its cutting-edge artificial intelligence (AI) and Internet of Things (IoT) solu...[Details]
Analog electronics
京公网安备 11010802033920号
EEWORLD
