E-, I-Grades ....................................... –40°C to 125°C
Storage Temperature Range .................. –65°C to 150°C
Lead Temperature (Soldering, 10 sec)
FE, R Packages Only ......................................... 300°C
PIN CONFIGURATION
TOP VIEW
TOP VIEW
OUT
OUT
OUT
OUT
I
LIM
SET
1
2
3
4
5
6
13
OUT
12 IN
11 IN
10 IN
9 IN
8 TEMP
7 I
MON
OUT
OUT
OUT
OUT
OUT
I
LIM
SET
OUT
1
2
3
4
5
6
7
8
17
OUT
16 OUT
15 IN
14 IN
13 IN
12 IN
11 TEMP
10 I
MON
9
OUT
TAB IS
OUT
FRONT VIEW
7
6
5
4
3
2
1
R PACKAGE
7-LEAD PLASTIC DD
T
JMAX
= 125°C,
θ
JA
= 34°C/W,
θ
JC
= 3°C/W
NC
IN
TEMP
OUT
I
MON
SET
I
LIM
DF PACKAGE
12-LEAD (4mm
×
4mm) PLASTIC DFN
T
JMAX
= 125°C,
θ
JA
= 41°C/W,
θ
JC
= 1.6°C/W
EXPOSED PAD (PIN 13) IS OUT, MUST BE SOLDERED TO PCB
FE PACKAGE
16-LEAD PLASTIC TSSOP
T
JMAX
= 125°C,
θ
JA
= 35°C/W,
θ
JC
= 2.3°C/W
EXPOSED PAD (PIN 17) IS OUT, MUST BE SOLDERED TO PCB
ORDER INFORMATION
LEAD FREE FINISH
LT3089EDF#PBF
LT3089IDF#PBF
LT3089EFE#PBF
LT3089IFE#PBF
LT3089ER#PBF
LT3089IR#PBF
TAPE AND REEL
LT3089EDF#TRPBF
LT3089IDF#TRPBF
LT3089EFE#TRPBF
LT3089IFE#TRPBF
LT3089ER#TRPBF
LT3089IR#TRPBF
PART MARKING*
3089
3089
3089FE
3089FE
LT3089R
LT3089R
PACKAGE DESCRIPTION
12-Lead (4mm × 4mm) Plastic DFN
12-Lead (4mm × 4mm) Plastic DFN
16-Lead Plastic TSSOP
16-Lead Plastic TSSOP
7-Lead Plastic DD-Pak
7-Lead Plastic DD-Pak
TEMPERATURE RANGE
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
For more information on lead free part marking, go to:
http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to:
http://www.linear.com/tapeandreel/.
Some packages are available in 500 unit reels through
designated sales channels with #TRMPBF suffix.
2
3089f
For more information
www.linear.com/LT3089
LT3089
ELECTRICAL CHARACTERISTICS
PARAMETER
SET Pin Current
Offset Voltage
(V
OUT
– V
SET
)
I
SET
Load Regulation
V
OS
Load Regulation
(Note 7)
Line Regulation
Minimum Load Current (Note 3)
Dropout Voltage (Note 4)
Internal Current Limit
I
LIM
Programming Ratio
I
LIM
Minimum Output Current Resistance
I
MON
Full-Scale Output Current
I
MON
Scale Factor
I
MON
Operating Range
TEMP Output Current (Note 9)
TEMP Output Current Absolute Error (Note 9)
Reference Current RMS Output Noise (Note 5)
Error Amplifier RMS Output Noise (Note 5)
Ripple Rejection
V
RIPPLE
= 0.5V
P-P
, I
LOAD
= 0.1A, C
SET
= 0.1µF,
C
OUT
=10µF, V
IN
= V
OUT(NOMINAL)
+ 3V
Thermal Regulation, I
SET
T
J
> 5°C
0°C <T
J
≤ 125°C
125°C <T
J
≤ 150°C
10Hz ≤ f ≤ 100kHz
I
LOAD
= 800mA, 10Hz ≤ f ≤ 100kHz, C
OUT
=10µF,
C
SET
= 0.1µF
f = 120Hz
f = 10kHz
f = 1MHz
10ms Pulse
75
–10
–15
5.7
27
90
75
20
0.003
I
LOAD
= 800mA
100mA ≤ I
LOAD
≤ 800mA
l
l
The
l
denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
J
= 25°C. (Note 2)
CONDITIONS
I
SET
V
OS
V
IN
= 2V, I
LOAD
= 3mA
2V ≤ V
IN
≤ 36V, 3mA ≤ I
LOAD
≤ 800mA
V
IN
= 2V, I
LOAD
= 3mA
V
IN
= 2V, I
LOAD
= 3mA
∆I
LOAD
= 3mA to 800mA
∆I
LOAD
= 3mA to 800mA
∆I
SET
∆V
OS
DF, FE Packages
R Package
∆V
IN
= 2V to 36V, I
LOAD
= 3mA
∆V
IN
= 2V to 36V, I
LOAD
= 3mA
2V ≤ V
IN
≤ 36V
I
LOAD
= 100mA
I
LOAD
= 800mA
V
IN
= 5V, V
SET
= 0V, V
OUT
= –0.1V
l
l
l
l
l
l
l
l
MIN
49.5
48.75
–1.5
–3.5
TYP
50
50
0
0
–0.1
–0.5
–1.5
1.5
0.001
1.1
1.21
1.47
MAX
50.5
51.25
1.5
3.5
–3
–4
UNITS
µA
µA
mV
mV
nA
mV
mV
nA/V
mV/V
3
1.65
210
190
V
OUT
+ 0.4V
mA
V
V
A
mA/kΩ
Ω
µA
µA/A
V
µA/°C
µA
µA
nA
RMS
µV
RMS
dB
dB
dB
%/W
0.8
155
130
V
OUT
– 40V
1
175
300
160
200
1
10
15
Note 1:
Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2:
Unless otherwise specified, all voltages are with respect to V
OUT
.
The LT3089 is tested and specified under pulse load conditions such
that T
J
≈ T
A
. The LT3089E is tested at T
A
= 25°C and performance is
guaranteed from 0°C to 125°C. Performance of the LT3089E over the
full –40°C and 125°C operating temperature range is assured by design,
characterization, and correlation with statistical process controls. The
LT3089I is guaranteed over the full –40°C to 125°C operating junction
temperature range. High junction temperatures degrade operating
lifetimes. Operating lifetime is degraded at junction temperatures greater
than 125°C.
Note 3:
Minimum load current is equivalent to the quiescent current of
the part. Since all quiescent and drive current is delivered to the output
of the part, the minimum load current is the minimum current required to
maintain regulation.
Note 4:
For the LT3089, dropout is specified as the minimum input-to-
output voltage differential required supplying a given output current.
Note 5:
Adding a small capacitor across the reference current resistor
lowers output noise. Adding this capacitor bypasses the resistor shot
noise and reference current noise; output noise is then equal to error
amplifier noise (see Applications Information section).
Note 6:
Diodes with series 400Ω resistors clamp the SET pin to the
OUT pin. These diodes and resistors only carry current under transient
overloads.
Note 7:
Load regulation is Kelvin sensed at the package.
Note 8:
This IC includes overtemperature protection that protects the
device during momentary overload conditions. Junction temperature
exceeds the maximum operating junction temperature when
overtemperature protection is active. Continuous operation above the
specified maximum operating junction temperature may impair device
reliability.
Note 9:
The TEMP pin output current represents the average die junction
temperature. Due to power dissipation and thermal gradients across the
die, the TEMP pin output current measurement does not guarantee that
absolute maximum junction temperature is not exceeded.
Why does gallium nitride perform better than other semiconductor materials?Here is a brief summary, the main points are as follows:
1. High breakdown electric field
2. High saturation speed
3. Outstan...
I've recently been working on 485-related communication equipment, but this is my first time dealing with it and I feel a bit lost. I hope someone can recommend some good books to me, thank you....
There is an underground city in Beijing. It is located at No. 62, Qianmen West Grinding Factory. The facade is very inconspicuous. After walking down more than 20 steps, you will enter a long passage....
I used useradd -G root -g root -d/home/arm arm to add an arm user. After setting the environment variables, I logged in again as the arm user. Why is the prompt still $? How can I change it to [arm@lo...
Everyone: My current problem is as follows: I now have an analog input board, which is Advantech's 2718. I plan to use a program-triggered polling method to read the board data. The rate requirement i...
A line scan lens is an industrial lens used with line scan cameras. Its imaging principle is to capture the image of the workpiece using a linear sensor and then perform digital signal processing t...[Details]
We are entering a new era where people are increasingly affordably equipped with more electronic gadgets. Electronics have become essential to our lives. For example, the average consumer now owns ...[Details]
On August 21st, Zhiyuan Robotics revealed at its first partner conference that it expects shipments to reach thousands of units this year and tens of thousands next year. The company hopes to reach...[Details]
UPS stands for Uninterruptible Power Supply, which includes energy storage devices. It is mainly used to provide uninterruptible power supply for devices that require high power stability.
...[Details]
1. Multi-channel DAC technology bottleneck
Currently,
the development of multi-channel DAC technology focuses on two core challenges.
First, industrial applications urgently ...[Details]
Previously, Positive Motion Technology shared with you the firmware upgrade of motion controller, ZBasic program development, ZPLC program development, communication with touch screen and input/out...[Details]
introduction
In recent years, multi-touch has emerged as a new alternative to traditional human-computer interaction. It eliminates the need for keyboards and mice, enabling simultaneous inter...[Details]
1. Introduction
In 2015, Apple's new MacBook and Apple Watch both featured force-sensing technology, which Apple calls Force Touch. Each time a user presses the touchpad, the device not only p...[Details]
On August 20, Huawei Device announced that the all-new M7 is the first to feature an in-cabin laser vision solution. This solution offers enhanced active safety capabilities compared to primary vis...[Details]
The power transmission system between a car's engine and drive wheels is called its drivetrain. It ensures the necessary traction and speed under various driving conditions, and coordinates these t...[Details]
In recent years, with the development of MOSFETs, they have gradually replaced transistors in the low-power, fast-switching industry. Major manufacturers in this field have also been reducing their...[Details]
Electronic devices are small individual components in electronic circuits. Transistors are common electronic components. Because of their wide range of applications, according to the usage of the e...[Details]
Recently, I received a request to use OK1028A-C to output PWM square wave. However, I found that there was no relevant instructions on the OK1028 platform, so I started writing this article.
A...[Details]
On August 19, Huawei's Executive Director and Chairman of the Device BG, Richard Yu, shared a Weibo post about a conversation he had with a Zunjie S800 owner. The owner had driven over 5,000 kilome...[Details]
RF/Wirelessly
京公网安备 11010802033920号
EEWORLD
