LTC6992IDCB-4#TRPBF datasheet, PDF

Datasheet> All Categories > Analog mixed-signal IC> The signal circuit> LTC6992IDCB-4#TRPBF

LTC6992IDCB-4#TRPBF: DescriptionIC OSC SILICON PROG 6-DFN; CategoryAnalog mixed-signal IC The signal circuit; File Size385KB，14 Pages; ManufacturerLinear ( ADI ); Websitehttp://www.analog.com/cn/index.html; Environmental Compliance

Download Datasheet Parametric View All

LTC6992IDCB-4#TRPBF Overview

IC OSC SILICON PROG 6-DFN

LTC6992IDCB-4#TRPBF Parametric

Parameter Name	Attribute value
Brand Name	Linear Technology
Is it Rohs certified?	conform to
Maker	Linear ( ADI )
Parts packaging code	DFN
package instruction	HVSON, SOLCC6,.12,20
Contacts	6
Manufacturer packaging code	DCB
Reach Compliance Code	compliant
ECCN code	EAR99
Analog Integrated Circuits - Other Types	ANALOG CIRCUIT
JESD-30 code	R-PDSO-N6
JESD-609 code	e3
length	3 mm
Humidity sensitivity level	1
Number of channels	1
Number of functions	1
Number of terminals	6
Maximum operating temperature	85 °C
Minimum operating temperature	-40 °C
Package body material	PLASTIC/EPOXY
encapsulated code	HVSON
Encapsulate equivalent code	SOLCC6,.12,20
Package shape	RECTANGULAR
Package form	SMALL OUTLINE, HEAT SINK/SLUG, VERY THIN PROFILE
Peak Reflow Temperature (Celsius)	NOT SPECIFIED
Certification status	Not Qualified
Maximum seat height	0.8 mm
Maximum supply voltage (Vsup)	5.5 V
Minimum supply voltage (Vsup)	2.25 V
Nominal supply voltage (Vsup)	3.3 V
surface mount	YES
technology	CMOS
Temperature level	INDUSTRIAL
Terminal surface	Matte Tin (Sn)
Terminal form	NO LEAD
Terminal pitch	0.5 mm
Terminal location	DUAL
Maximum time at peak reflow temperature	NOT SPECIFIED
width	2 mm

Preview

Download Datasheet

View All

DEMO MANUAL DC1562B

LTC699X-X

TimerBlox: Oscillators, One Shots,

PWM, Delay, Power on Reset

Description

Demonstration circuit 1562B is an engineering tool to

design and evaluate the LTC699X-X family of TimerBlox

circuits. The center section of the board contains a pre-

configured TimerBlox function. DC1562B comes in twelve

timing function variations as outlined in Table 1.

Surrounding the center board is a playground prototyping

area. The prototyping area has pads for DIP-8, S8, MS8,

or S6 packages with bread boarding connections to each

pin and two convenient power buses and ground bus

surrounding the entire area. This area is for conditioning

signals to control the timer function and for adding loads

controlled in time.

The center part of the board can be detached as a stream-

lined circuit, to combine with a pre-existing circuit. For

application flexibility, a provision is made for buffering and

inverting the output of the timer. An optional NC7W04P6X

SC70 package dual inverter can be added at U2 to provide

this functionality.

Design files for this circuit board are available at

http://www.linear.com/demo

LT, LTC, LTM, Linear Technology, TimerBlox and the Linear logo are registered trademarks

of Linear Technology Corporation. All other trademarks are the property of their respective

owners.

Using the Demo BoarD

To understand the simplicity and flexibility of the TimerBlox

function, download the appropriate data sheet from the LTC

website,

www.linear.com.

Each evaluation board comes

with a TimerBlox part, decoupling cap and a bulk decou-

pling 10µF tantalum cap. Resistors are also installed that

configure the TimerBlox device so that they are ready to use

by simply adding power. Changing the default configura-

tion of the demo board is a simple matter of determining

a few new resistor values. Simply select a pair of resistor

values for the DIV value from the data sheet DIV table,

calculate the value of R

SET

required, replace the resistor

on the board, apply power, and go! Single supply power

between 2.25V and 5.5V and ground must be supplied

directly to the center board.

The outer prototyping section of the board can be used

with single or dual supplies as required.

When using the

prototyping area, the outermost trace, which is ground,

must be connected (hand wired) to the ground on the

center board section.

All input and output holes are sized

for 65mil turret terminals, or wires can be soldered in the

holes directly.

Changing the timer configuration requires changing re-

sistor values on the center board. The resistor lead holes

can accept “pressed-in” DIP sockets, or resistors can

be soldered directly in the holes. Pads for 0805 surface

mount resistors are also included at each position where

a leaded resistor could be used. Pads are also included

for three 25-turn trim pots which can be used to replace

SET

(R8) for master oscillator frequency adjustment, PSF

in (R10) for voltage controlled options, and R

DEV

(R7) for

frequency divider control to permit real-time adjustments

while running.

dc1562bfa

Recommended Resources

Make automatic lighting with TWH9250

Circuit that stabilizes the static operating point

2kHz dual T frequency selective amplifier

Fast 1.5V flash circuit

MC3359 receiving circuit

TDA1521 power amplifier circuit

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components