847 Technical Data Sheet
Carbon Conductive Assembly Paste
ISO 9001:2008 Registered Quality System. Burlington, Ontario, CANADA
SAI Global File: 004008
847
Description
The 847
Carbon Conductive Assembly Paste
is an electrically conductive, low-cost, non-silicone product for
applications needing stability over wide thermal ranges. The synthetic oil that is used has a low
evaporation rate that allows the paste withstand high temperatures without drying. Further, the paste
resists separation and bleeding very well, so it is unlikely to contaminate onto nearby areas.
Applications & Usages
The 847 paste improves electrical conductivity between electrical contacts and inhibits corrosion.
Features and Benefits
•
•
•
•
•
•
High conductivity
of 0.04 S/cm
and low volume resistivity
of 23
Ω·cm
Doesn’t separate or bleed like silicone-based
oil
Withstands high temperature without drying, bleeding, flowing, or chemical degradation
Lubricates even at low temperature
Non-Corrosive
Zero VOC
Usage Parameters
Properties
Shelf Life
a)
Value
5y
Temperature Ranges
Properties
Constant Service
Temperature
Maximum Intermittent
Temperature
Storage Temperature
Limits
b)
Value
-68 to 165 °C
[-90 to 329 °F]
200 °C
[392 °F]
-40 to 40 °C
[-40 to 104 °F]
a) Reported shelf life assumes room
temperature storage and unopened container.
b) Room temperature is acceptable. Cold storage
avoids material separation and settling. If
storing at 25 °C, mix thoroughly to disperse
filler before use.
Principal Components
Name
High Temperature, Synthetic Oil (Non-silicone based)
Carbon Black
CAS Number
proprietary
1333-86-4
Page
1
of
4
Date: 05 January 2018 / Ver. 1.07
Carbon Conductive
Assembly Paste
847 Technical Data Sheet
847
Properties
Electrical Properties
Volume Resistivity (
v
)
Volume Conductivity (
v
)
Surface Resistivity (
s
)
Surface Conductivity (
s
)
Grease Properties
Evaporation Loss, 22 h @165 °C [329 °F]
Oil Separation, 30 h @165 °C [329 °F]
Dropping Point
Water Washout @38 °C [100 °F]
Worked Penetration, 60 strokes, ½ scale
Emcor Rust Test, distilled water
Method
Mil-Std-883J Method 5011.6
"
ASTM D257, ASTM D4496
"
Method
ASTM D 2595
ASTM D 6184
ASTM D 2265
ASTM D 1264
ASTM D 1403
IP 220
Value
23
·cm
0.04 S/cm
271
/sq
0.0037 S/sq
Value
0.3%
1.8%
>304 °C [>579 °F]
0.2%
174
#3
a)
a) Corroded areas covering >1% but <5% of the running track surface.
Physical Properties
Color
Odor
Density @25 °C [77 °F]
Viscosity
Lubricant
Bleed Resistant
Run Resistant
Corrosion Resistant
VOC (Volatile Organic Compound)
Synthetic Oil Properties
Oil Viscosity Index
b)
Pour Point
Fire Point
c)
Flash Point
d)
Method
Visual
ASTM D 1475
Value
Black
Odorless
1.07 g/mL
Thixotropic paste
Yes
Yes
Yes
Yes
0%
Value
>110 °C
≥-34
°C
321 °C
>290 °C
Method
ASTM D 2270
ASTM D 92
ASTM D 92
[>230 °F]
[≥-29 °F]
[610 °F]
[>554 °F]
Note:
Values based on synthetic oil component only
b) High oil viscosity index of more than a 100 indicate small oil viscosity change with temperature.
c) Temperature at which oil will continue to burn for at least 5 seconds after ignition with an open flame.
d) Cleveland open cup method.
Storage
Store between -40 and 40 °C [40 and 104 °F] in dry area.
Page
2
of
4
Date: 05 January 2018 / Ver. 1.07
Carbon Conductive
Assembly Paste
847 Technical Data Sheet
847
Health, Safety, and Environmental Awareness
Please see the 847
Safety Data Sheet
(SDS) for greater details on transportation, storage, handling and
other security guidelines.
Environmental Impact:
The VOC (Volatile Organic Compound) content is 0% by WHMIS and European
standards.
Health and Safety:
Wear safety glasses and disposable gloves to avoid exposures.
HMIS® RATING
HEALTH:
FLAMMABILITY:
PHYSICAL HAZARD:
PERSONAL PROTECTION:
Approximate HMIS and NFPA Risk Ratings Legend:
0 (Low or none); 1 (Slight); 2 (Moderate); 3 (Serious); 4 (Severe)
NFPA® 704 CODES
0
1
0
1
0
0
Application Instructions
The conductive paste performance depends on mainly on surface preparation. Improperly prepared
contact surfaces can degrade the pastes’ stability, conductivity, and lubrication characteristics. While the
thickness and coverage are also important, the application method itself can easily be adjusted according
to performance and application needs.
Prerequisites
•
•
Wear gloves and protective clothing (see 847 SDS). This product is extremely messy.
Clean and dry the surface of the substrate to remove other oils, greases, dust, water, solvents, or
any other contaminants.
Recommendation:
Use MG 824 Isopropyl Alcohol
Equipment
•
•
•
Lint free cloth (for cleaning contact and for wiping excess residue)
Spatula or stick application tools (sized appropriately for your application)
Isopropyl alcohol or other residue-free organic solvents
N
OTE
:
Avoid oil-based cleaners (like WD-40) that are designed to leave a film on the metal surface.
Contaminant oil or grease films may act like barriers reducing the electrical contact between the
conductive paste and the metallic substrate.
To apply the paste
1. Wipe the contact with a lint-free cloth.
2. Clean the contacts with isopropyl alcohol or other non-oil based cleaner.
3. Once dry, apply the paste with the application tool to the contact, ensuring adequate coverage and
desired thickness.
Page
3
of
4
Date: 05 January 2018 / Ver. 1.07
Carbon Conductive
Assembly Paste
847 Technical Data Sheet
847
A
TTENTION
!
DO NOT apply or smooth grease with bare finger. Carbon black is hard to clean and may transfer to other
surfaces by touch. Further, you may introduce contaminants that degrade the overall performance of the
grease.
Packaging and Supporting Products
Cat. No.
847-25ML
847-1P
847-1G
Packaging
Jar
Jar
Pail
Net Volume
25 mL
466 mL
3.78 L
0.84 fl oz
15.7 fl oz
1.0 gal
Net Weight
26.8 g
500 g
4.05 kg
0.94 oz
17.6 oz
8.94 lb
Contact MG Chemicals if custom packaging or sizes are required
Supporting Products
•
Isopropyl Alcohol:
Cat. No.824
Technical Support
Contact us regarding any questions, improvement suggestions, or problems with this product. Application
notes, instructions, and FAQs are located at
www.mgchemicals.com.
Email:
support@mgchemicals.com
Phone: +(1) 800-340-0772 (Canada, Mexico & USA)
+(1) 905-331-1396 (International)
Fax: +(1) 905-331-2862 or +(1) 800-340-0773
Mailing address:
Manufacturing & Support
1210 Corporate Drive
Burlington, Ontario, Canada
L7L 5R6
Head Office
9347–193rd Street
Surrey, British Columbia, Canada
V4N 4E7
Disclaimer
This information is believed to be accurate. It is intended for professional end users having the skills to
evaluate and use the data properly.
M.G. Chemicals Ltd.
does not guarantee the accuracy of the data and
assumes no liability in connection with damages incurred while using it.
Page
4
of
4
Date: 05 January 2018 / Ver. 1.07
京公网安备 11010802033920号
EEWORLD
