EXPOSED PAD (PIN 9) IS GND, MUST BE SOLDERED TO PCB
MS8E PACKAGE
8-LEAD PLASTIC MSOP
T
JMAX
= 150°C,
θ
JA
= 29°C/W TO 45°C/W,
θ
JC
= 5°C/W TO 10°C/W
EXPOSED PAD (PIN 9) IS GND, MUST BE SOLDERED TO PCB
orDer inForMaTion
LEAD FREE FINISH
LT3062EDCB#PBF
LT3062IDCB#PBF
LT3062HDCB#PBF
LT3062MPDCB#PBF
LT3062EMS8E#PBF
LT3062IMS8E#PBF
LT3062HMS8E#PBF
LT3062MPMS8E#PBF
LT3062EDCB-3.3#PBF
LT3062IDCB-3.3#PBF
LT3062EDCB-5#PBF
LT3062IDCB-5#PBF
TAPE AND REEL
LT3062EDCB#TRPBF
LT3062IDCB#TRPBF
LT3062HDCB#TRPBF
LT3062MPDCB#TRPBF
LT3062EMS8E#TRPBF
LT3062IMS8E#TRPBF
LT3062HMS8E#TRPBF
http://www.linear.com/product/LT3062#orderinfo
PART MARKING*
LGNC
LGNC
LGNC
LGNC
LTGND
LTGND
LTGND
LTGND
LGYX
LGYX
LGYY
LGYY
PACKAGE DESCRIPTION
8-Lead (2mm
×
3mm) Plastic DFN
8-Lead (2mm
×
3mm) Plastic DFN
8-Lead (2mm
×
3mm) Plastic DFN
8-Lead (2mm
×
3mm) Plastic DFN
8-Lead Plastic MSOP
8-Lead Plastic MSOP
8-Lead Plastic MSOP
8-Lead Plastic MSOP
8-Lead (2mm
×
3mm) Plastic DFN
8-Lead (2mm
×
3mm) Plastic DFN
8-Lead (2mm
×
3mm) Plastic DFN
8-Lead (2mm
×
3mm) Plastic DFN
TEMPERATURE RANGE
–40°C to 125°C
–40°C to 125°C
–40°C to 150°C
–55°C to 150°C
–40°C to 125°C
–40°C to 125°C
–40°C to 150°C
–55°C to 150°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
LT3062MPMS8E#TRPBF
LT3062EDCB-3.3#TRPBF
LT3062IDCB-3.3#TRPBF
LT3062EDCB-5#TRPBF
LT3062IDCB-5#TRPBF
2
3062fa
For more information
www.linear.com/LT3062
LT3062 Series
orDer inForMaTion
LEAD FREE FINISH
LT3062EMS8E-3.3#PBF
LT3062IMS8E-3.3#PBF
LT3062EMS8E-5#PBF
LT3062IMS8E-5#PBF
TAPE AND REEL
LT3062EMS8E-3.3#TRPBF
LT3062IMS8E-3.3#TRPBF
LT3062EMS8E-5#TRPBF
LT3062IMS8E-5#TRPBF
http://www.linear.com/product/LT3062#orderinfo
PART MARKING*
LTGZG
LTGZG
LTGZF
LTGZF
PACKAGE DESCRIPTION
8-Lead Plastic MSOP
8-Lead Plastic MSOP
8-Lead Plastic MSOP
8-Lead Plastic MSOP
TEMPERATURE RANGE
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
For more information on lead free part marking, go to:
http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to:
http://www.linear.com/tapeandreel/.
Some packages are available in 500 unit reels through
designated sales channels with #TRMPBF suffix.
The
l
denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C. (Note 3)
PARAMETER
Minimum Input Voltage (Note 4)
Regulated Output Voltage (Note 5)
CONDITIONS
I
LOAD
= 200mA
LT3062-3.3: V
IN
= 3.9, I
LOAD
= 1mA
LT3062-3.3: 3.9V < V
IN
< 45V, 1mA < I
LOAD
< 200mA
LT3062-5: V
IN
= 5.6, I
LOAD
= 1mA
LT3062-5: 5.6V < V
IN
< 45V, 1mA < I
LOAD
< 200mA
V
IN
= 2.1V, I
LOAD
= 1mA
2.1V < V
IN
< 45V, 1mA < I
LOAD
< 200mA (E-, I-Grades)
2.1V < V
IN
< 45V, 1mA < I
LOAD
< 200mA (MP-, H-Grades)
LT3062-3.3: ΔV
IN
= 3.9V to 45V (E-, I-Grades)
LT3062-5: ΔV
IN
= 5.6V to 45V (E-, I-Grades)
LT3062: ΔV
IN
= 2.1V to 45V (E-, I-Grades)
LT3062: ΔV
IN
= 2.1V to 45V (MP-, H-Grades)
Load Regulation (Note 4)
ΔI
LOAD
= 1mA to 200mA
LT3062-3.3: V
IN
= 3.9V (E-, I-Grades)
LT3062-5: V
IN
= 5.6V (E-, I-Grades)
LT3062: V
IN
= 2.1V (E-, I-Grades)
LT3062: V
IN
= 2.1V (MP-, H-Grades)
Dropout Voltage
V
IN
= V
OUT(NOMINAL)
(Notes 6, 7)
I
LOAD
= 1mA
I
LOAD
= 1mA
I
LOAD
= 10mA
I
LOAD
= 10mA
I
LOAD
= 100mA
I
LOAD
= 100mA
I
LOAD
= 200mA
I
LOAD
= 200mA
GND Pin Current
V
IN
= V
OUT(NOMINAL)
+ 0.6V
(Notes 6, 8)
I
LOAD
= 0
I
LOAD
= 1mA
I
LOAD
= 10mA
I
LOAD
= 100mA
I
LOAD
= 200mA
C
OUT
= 10µF, I
LOAD
= 200mA, C
REF/BYP
= 0.01µF
V
OUT
= 600mV, BW = 10Hz to 100kHz
l
l
l
l
l
l
l
l
l
l
l
l
l
l
elecTrical characTerisTics
MIN
3.267
3.234
4.950
4.900
594
588
585
TYP
1.6
3.3
5
600
600
600
1.6
3.1
0.5
7.1
7.6
0.3
65
130
MAX
2.1
3.333
3.366
5.050
5.100
606
612
612
22
33
4
6
28
39
4
9
110
180
180
270
290
430
360
530
90
120
500
4
10
UNITS
V
V
V
V
V
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
µA
µA
µA
mA
mA
µV
RMS
ADJ Pin Voltage (Notes 4, 5)
Line Regulation (Note 4)
I
LOAD
= 1mA
l
250
l
300
l
l
l
l
l
l
45
70
225
2
5
30
Output Voltage Noise
3062fa
For more information
www.linear.com/LT3062
3
LT3062 Series
The
l
denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C. (Note 3)
PARAMETER
ADJ Pin Bias Current (Notes 4, 9)
Shutdown Threshold
SHDN
Pin Current (Note 10)
Quiescent Current in Shutdown
V
OUT
= Off to On
V
OUT
= On to Off
V
SHDN
= 0V
V
SHDN
= 45V
V
IN
= 45V, V
SHDN
= 0V
58
55
70
l
l
elecTrical characTerisTics
CONDITIONS
MIN
l
l
l
l
l
TYP
15
0.8
0.7
1.2
0.3
73
70
85
320
MAX
60
1.5
<1
3
1
UNITS
nA
V
V
µA
µA
µA
dB
dB
dB
mA
mA
0.3
Ripple Rejection
LT3062-3.3
V
IN
– V
OUT
= 1.5V (AVG), V
RIPPLE
= 0.5V
P-P
, LT3062-5
f
RIPPLE
= 120Hz, I
LOAD
= 200mA
LT3062 (Note 4)
Current Limit
Input Reverse Leakage Current
Reverse Output Current (Note 13)
V
IN
= 7V, V
OUT
= 0
V
IN
= V
OUT(NOMINAL)
+ 1V (Note 11), ΔV
OUT
= –5%
V
IN
= -45V, V
OUT
= 0
LT3062-3.3: V
OUT
= 3.3V, V
IN
= V
SHDN
= 0V
LT3062-5: V
OUT
= 5V, V
IN
= V
SHDN
= 0V
LT3062: V
OUT
= 1.2V, V
IN
= V
SHDN
= 0V
220
1
5.2
5.2
0.2
15
15
10
mA
µA
µA
µA
Note 1:
Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2:
Absolute maximum input to output differential voltage is not
achievable with all combinations of rated IN pin and OUT pin voltages.
With the IN pin at 50V, the OUT pin may not be pulled below 0V. The total
measured voltage from IN to OUT must not exceed ±50V. If OUT is above
ground, do not pull IN more than 40V below OUT.
Note 3:
The LT3062 is tested and specified under pulse load conditions
such that T
J
≅
T
A
. The LT3062E regulators are 100% tested at T
A
= 25°C
and performance is guaranteed from 0°C to 125°C. Performance at
–40°C to 125°C is assured by design, characterization and correlation
with statistical process controls. The LT3062I regulators are guaranteed
over the full –40°C to 125°C operating junction temperature range. The
LT3062MP regulators are 100% tested over the –55°C to 150°C operating
junction temperature. The LT3062H regulators are 100% tested at the
150°C operating junction temperature. High junction temperatures degrade
operating lifetimes. Operating lifetime is derated at junction temperature
greater than 125°C.
Note 4:
The LT3062 adjustable version is tested and specified for these
conditions with the ADJ connected to the OUT pin.
Note 5:
Maximum junction temperature limits operating conditions. The
regulated output voltage specification does not apply for all possible
combinations of input voltage and output current. Limit the output current
range if operating at the maximum input voltage. Limit the input-to-output
voltage differential if operating at maximum output current. Current limit
foldback limits the maximum output current as a function of input-to-
output voltage. See Current Limit vs V
IN
– V
OUT
in the Typical Performance
Characteristics section.
Note 6:
To satisfy minimum input voltage requirements, the LT3062
adjustable version is tested and specified for these conditions with an
external resistor divider (bottom 60k, top 230k) for an output voltage of
2.9V. The external resistor divider adds 10µA of DC load on the output.
The external current is not factored into GND pin current.
Note 7:
Dropout voltage is the minimum input-to-output voltage
differential needed to maintain regulation at a specified output current. In
dropout, the output voltage equals: (V
IN
– V
DROPOUT
).
Note 8:
GND pin current is tested with V
IN
= V
OUT(NOMINAL)
+ 0.6V and a
current source load. GND pin current will increase in dropout. See GND
pin current curves in the Typical Performance Characteristics section. For
fixed voltage options, an internal resistor divider will add 5μA to the GND
pin current. See the GND Pin Current curves in the Typical Performance
Characteristics section.
Note 9:
ADJ pin bias current flows out of the ADJ pin.
Note 10:
SHDN
pin current flows into the
SHDN
pin.
Note 11:
To satisfy requirements for minimum input voltage, current limit
is tested at V
IN
= V
OUT(NOMINAL)
+ 1V or V
IN
= 2.1V, whichever is greater.
Note 12:
This IC includes thermal limit which protects the device during
momentary overload conditions. Junction temperature exceeds 125°C
(E-Grade and I-Grade) or 150°C (MP-Grade and H-Grade) when thermal
limit is active. Continuous operation above the specified maximum
junction temperature may impair device reliability.
Note 13:
Reverse output current is tested with the IN pin grounded and the
OUT pin forced to the specified voltage. This current flows into the OUT
How to select devices (MCU or other IC) and solution design knowledge (recently selecting motor IC solutions)? Are there any related books or method suggestions? Please give me some advice:congratulat...
This design is based on the DAC output of stm32f429, with a total of 8 channels, 2 of which are DACs built into the chip, and the other 6 are analog voltages output through PWM plus RC circuits. The i...
High efficiency and low standby power consumption are two major challenges in today's switching power supply design. Resonant topology or LLC topology is becoming increasingly popular because it ca...[Details]
introduction
my country has a vast territory and a large population. The scale of housing construction is huge, and the amount of residential construction is large and wide. It is still on t...[Details]
The Mobile Industry Processor Interface (MIPI) Alliance is an organization responsible for promoting the standardization of software and hardware in mobile devices. It has released the D-PHY specif...[Details]
Abstract: In order to generate a stable excitation signal, the design of a digital frequency synthesizer is implemented on FPGA using Verilog hardware language. The design includes accumulator, wav...[Details]
I. Introduction
In the field of power conversion, isolated converters (forward, flyback, and double-ended) with low output DC voltage all use MOSFET as the rectifier device. Since these devi...[Details]
1 Introduction
Ultrasonic waves have strong directivity, slow energy consumption, and can propagate over long distances in a medium, so they are used for distance measurement. Ultrasonic detec...[Details]
With the development and widespread application of computer technology, especially in the field of industrial control, computer communication is particularly important. Although serial communication g...[Details]
This controller uses PIC16C54 single-chip microcomputer as the controller, and it is very easy to use: just connect a telephone line to the loudspeaker through the controller, and you can rem...[Details]
Capacitors
are basic components in various electronic devices and are widely used for bypassing, coupling,
filtering
, tuning, etc. in electronic circuits. However, to use capacitors,...[Details]
introduction
MEMS is a high-tech that has flourished on the basis of integrated circuit production technology and dedicated micro-electromechanical processing methods. Pressure sensors develop...[Details]
LED guardrail lights use fluorescent tubes or LEDs as light sources and continuous guardrails as carriers to form an approximately linear guardrail light strip. This article mainly introduces...[Details]
1. Overview
At present, an information revolution is in the ascendant around the world, led by microelectronics, computers and communication technologies, and centered on information technolog...[Details]
1 Introduction
With the improvement of people's quality of life, lamps are no longer just basic indoor lighting tools, but also a kind of practical art for architectural decoration. When ther...[Details]
Distributed Wireless Communication System (DWCS) uses distributed antennas, distributed processing control, joint signal processing and other technologies to improve the system's spectrum efficie...[Details]
Electronics Design Contest
京公网安备 11010802033920号
EEWORLD
