address inputs, A(12:0); and eight bidirectional data lines,
DQ(7:0). E1 and E2 are device enable inputs that control device
selection, active, and standby modes. Asserting both E1 and E2
enables the device, causes I
DD
to rise to its active value, and
decodes the 13 address inputs to select one of 8,192 words in
the memory. W controls read and write operations. During a
read cycle, G must be asserted to enable the outputs.
2
WRITE CYCLE
A combination of W less than V
IL
(max), E1 less than V
IL
(max),
and E2 greater than V
IH
(min) defines a write cycle. The state of
G is a “don’t care” for a write cycle. The outputs are placed in
the high-impedance state when either G is greater than
V
IH
(min), or when W is less than V
IL
(max).
Write Cycle 1, the Write Enable-controlled Access shown in
figure 4a, is defined by a write terminated byW going high, with
E1 and E2 still active. The write pulse width is defined by t
WLWH
when the write is initiated by W, and by t
ETWH
when the write
is initiated by the latter of E1 or E2. Unless the outputs have
been previously placed in the high-impedance state by G, the
user must wait t
WLQZ
before applying data to the eight
bidirectional pins DQ(7:0) to avoid bus contention.
Write Cycle 2, the Chip Enable-controlled Access shown in
figure 4b, is defined by a write terminated by the latter of E1 or
E2 going inactive. The write pulse width is defined by t
WLEF
when the write is initiated by W, and by t
ETEF
when the write
is initiated by the latter of E1 or E2 going active. For the W
initiated write, unless the outputs have been previously placed
in the high-impedance state by G, the user must wait t
WLQZ
before applying data to the eight bidirectional pins DQ(7:0) to
avoid bus contention.
Total Dose
Table 2. Radiation Hardness
Design Specifications
1
1.0E6
1.0E9
1.0E12
1.0E-10
3.0E14
rads(Si)
rads(Si)/s 20ns pulse
rads(Si)/s 20ns pulse
errors/bit day
2
n/cm
2
Dose Rate Upset
Dose Rate Survival
Single-Event Upset
Neutron Fluencs
Notes:
1. The SRAM will not latchup during radiation exposure under recommended
operating conditions.
2. 90% Adam’s worst case spectrum (-55
o
C to 125+
o
C).
Table 3. SEU versus Temperature
10
-4
10
-6
SEU
errors/bit-day
10
-8
10
-10
10
-12
10
-13
10
-14
10
-16
10
-13
10
-11
10
-10
RADIATION HARDNESS
The UT67164 SRAM incorporates special design and layout
features which allow operation in high-level radiation
environments.
-55
-35
-15
5
25
45
65
85
105 125
Temperature (
o
C)
3
ABSOLUTE MAXIMUM RATINGS
1
(Referenced to V
SS
)
SYMBOL
V
DD
V
I/O
T
STG
P
D
T
J
Θ
JC
I
LU
I
I
PARAMETER
DC supply voltage
Voltage on any pin
Storage temperature
Maximum power dissipation
Maximum junction temperature
Thermal resistance, junction-to-case
2
Latchup immunity
DC input current
LIMITS
-0.5 to 7.0V
-0.5 to V
DD
+ 0.5
-65 to +150°C
1.0W
+150°C
10°C/W
+/-150mA
+/-
10 mA
Notes:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, and functional operation of the device
at these or any other conditions beyond limits indicated in the operational sections of this specification is not recommended. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
2. Test per MIL-STD-883, Method 1012.
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD
T
C
V
IN
PARAMETER
Positive supply voltage
Case temperature range
DC input voltage
LIMITS
4.5 to 5.5V
-55 to +125°C
0V to V
DD
UNITS
V
o
C
V
4
DC ELECTRICAL CHARACTERISTICS (Pre/Post-Radiation)*
(V
DD
= 5.0V±10%; -55°C <Tc < +125°C)
SYMBOL
V
IH
V
IL
V
OL
V
OH
C
IN 1
C
IO 1
I
IN
I
OZ
PARAMETER
High-level input voltage
Low-level input voltage
Low-level output voltage
High-level output voltage
Input capacitance
Bidirectional I/O capacitance
Input leakage current
Three-state output leakage current
I
OL
= +/- 4.0mA, V
DD
= 4.5V
I
OH
= +/-4mA, V
DD
= 4.5V
ƒ
= 1MHz @ 0V, V
DD
= 4.5V
ƒ
= 1MHz @ 0V, V
DD
= 4.5V
V
IN
= V
DD
and V
SS
V
O
= V
DD
and V
SS
V
DD
= 5.5V
G = 5.5V
I
OS 2, 3
Short-circuit output current
V
DD
= 5.5V, V
O
= V
DD
V
DD
= 5.5V, V
O
= 0V
I
DD
(OP)
I
DD
(SB)
pre-rad
I
DD
(SB)
post-rad
Supply current operating @1MHz
CMOS inputs (I
OUT
= 0)
V
DD
= 5.5V
Supply current standby
CMOS inputs (I
OUT
= 0)
E1 = V
DD
- 0.5, V
DD
= 5.5V
CMOS inputs (I
OUT
= 0)
CS1 = negated V
DD
= 5.5V
CS2 = negated
Notes:
* Post-radiation performance guaranteed at 25°C per MIL-STD-883 Method 1019 at 1.0E6 rads(Si).
1. Measured only for initial qualification and after process or design changes that could affect input/output capacitance.
2. Supplied as a design limit but not guaranteed or tested.
3. Not more than one output may be shorted at a time for maximum duration of one second.
The factory bought a batch of power supplies without dimming function. In order to achieve dimming, an independent power supply dimming module must be designed. The module requires a wide voltage AC p...
I am a beginner in filter driver transparent encryption and decryption development. I have learned the source code of tooflat and successfully compiled it with ifs kit. After installing it and restart...
Find the RC delay circuit
Conditions: Power supply VCC = 18V ( provided by bridge rectifier filtering ) , the components used are conventional components such as resistors, capacitors, and transistors...
The intensity obtained by the X-NUCLEO-IKA01A3 magnetic sensor has three values: x, y, and z. After testing, the change direction mainly affects the data x and y, while the data z has little effect. I...
There are many different ways of human-computer interaction. The more common ones are listed below:
Mouse interaction: Using a mouse to operate a computer and interact was the most common human...[Details]
If the ultimate form of a car is a silicon-based life form, then in
the field of
intelligent driving
, it has gradually taken on the appearance of a "veteran driver." In
the field of
the ...[Details]
With the rapid development of technology, automotive intelligence is increasing at an unprecedented rate. This not only enhances vehicle functionality and comfort, but also places higher deman...[Details]
As the scale and business applications of national e-government networks continue to expand, the data and services transmitted over them are becoming increasingly sensitive and critical. To protect...[Details]
Normally, we determine our location and where we want to go by comparing our surroundings with observation and simple GPS tools. However, this kind of reasoning is very difficult for self-driving c...[Details]
With the increasing number of new energy vehicles on the road, the deployment of supporting facilities for these vehicles has accelerated, and new energy vehicles have gradually entered the vision ...[Details]
Wearable technology is taking off, with applications evolving rapidly, from smartwatches to fitness trackers and even smart wigs! Bluetooth Smart is at the center of this revolution. This is the se...[Details]
As my country's industrialization continues to improve, environmental pollution is also facing tremendous pressure. In recent years, national environmental protection policies have become increasin...[Details]
Charge your electric car for just six minutes and you'll get 1,000 kilometers! This isn't just a scene from a science fiction film, but a reality made possible by Guoxuan High-Tech's Jinshi solid-s...[Details]
Fast charging is a method and means of quickly replenishing a vehicle's power. It is the core and most important part of electric vehicles. Speaking of fast charging, everyone is familiar with it. ...[Details]
The number of new energy vehicles in use is increasing, and there are multiple choices available. New energy vehicles can be divided into hybrid and pure electric, and the types of hybrid include m...[Details]
On August 19, according to foreign media Cyber Security News reported yesterday, a cybersecurity researcher discovered that hundreds of publicly accessible TeslaMate installation programs are leaki...[Details]
In the first half of 2025, Chinese companies demonstrated overwhelming advantages in the world's four major material fields: in the global loading of positive electrode materials, Chinese companies...[Details]
According to foreign media reports, due to the massive expansion of Chinese companies in the global electric vehicle market, the capacity utilization rate of South Korea's three major battery manuf...[Details]
We often notice that some safety light curtains have EDM function. What does EDM mean here? What is its function?
The full name of EDM is External Device Monitor, which means external device m...[Details]
Analogue and Mixed Signal
京公网安备 11010802033920号
EEWORLD
