DTS24Z25-35AE [V001] datasheet, PDF

DTS24Z25-35AE [V001]: DescriptionRECP ASSY; CategoryThe connector; File Size856KB，17 Pages; ManufacturerTE Connectivity; Websitehttp://www.te.com; Environmental Compliance

Download Datasheet Parametric View All

DTS24Z25-35AE [V001] Overview

RECP ASSY

Parameter Name	Attribute value
Connector System	line to panel, line to panel
Sealable	yes
Connectors and terminals terminate to	Wires and cables
Housing size	25
shield	yes
Connector type	female end, female end
Housing type	Lock nut female end
Number of Positions	128
Number of power supply locations	0
Number of signal positions	128
Pre-installed	no
Shell plating material	black zinc nickel alloy
Shell material	Aluminum 6061-T6
Insulation Materials	Hard dielectric/silica gel
Sealed	no
Contact Current Rating (Max) (A)	5
reverse polarity	no
Terminal layout	25 – 35
Terminal type	Less Pin
Connector mounting type	Panel
polar code	E
Joint alignment type	keying
joint fixation	with
Location monitoring	Timing
Cable size	.08 – .33 mm² [ 28 – 22 AWG ]
Working group temperature range	-65 – 200 °C [ -85 – 392 °F ]
Circuit Application	Signal

Please help!: Hey guys, my T1CNT can't count automatically in CCS environment, but my enable bits have been set. The program of initial event manager is as follows:void init_EV(void){EvaRegs.T1CNT=0; // The initial...; lance0220 Analogue and Mixed Signal

[GD32E231 Work Submission] Quartz Accelerometer Acquisition: IntroductionThe quartz accelerometer is a high-precision acceleration sensor with a higher range and stability than MEM. It can be combined with various gyroscope systems to achieve high-precision att...; wolfg4 GD32 MCU

Learning simulation + reading notes on "Operational Amplifier Noise Optimization Handbook" (Part 1): [i=s]This post was last edited by dontium on 2015-1-23 11:33[/i] Noise is defined as any unwanted signal in an electronic system. Noise includes inherent noise and external noise. The spice simulation...; 一潭清水 Analogue and Mixed Signal

Can two devices communicate using the Jtag interface?: I am working on a project recently, combining two existing devices. The two devices' CPUs need to communicate, and all interfaces have other uses, leaving only one Jtag. Is there any way to use Jtag f...; hanxiao007 Embedded System

[Repost] Repost a good article to learn STM8: Section 1: Mood and Clock To be honest, I don't have many microcontrollers that I can use. I always think that any microcontroller can develop a good product. In the past few years, I used 51 and alwa...; tiankai001 stm32/stm8

430 serial port wakeup: When the 430 microcontroller enters LPM3 mode at a baud rate of 9600, it can only wake up after receiving 10 bytes. How can I make it wake up after receiving 1 byte?...; newnew0601 Microcontroller MCU

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components