DTS24N21-16XD [V001] datasheet, PDF

DTS24N21-16XD [V001]: DescriptionHERM RECP; CategoryThe connector; File Size856KB，17 Pages; ManufacturerTE Connectivity; Websitehttp://www.te.com

Download Datasheet Parametric View All

DTS24N21-16XD [V001] Overview

HERM RECP

Parameter Name	Attribute value
Connector System	line to panel, line to panel
Sealable	yes
Connectors and terminals terminate to	Wires and cables
Housing size	21
Housing type	Lock nut female end
Number of Positions	16
Number of power supply locations	0
Number of signal positions	16
Pre-installed	no
Shell material	Stainless steel
Insulation Materials	Glass
Sealed	yes
Contact Current Rating (Max) (A)	13
reverse polarity	standard
Terminal layout	21 – 16
Terminal type	eyelet pin
polar code	D
Joint alignment type	keying
Joint fixation type	Thread
Location monitoring	0°
Cable size (AWG)	16 – 20
Working group temperature range	-65 – 200 °C [ -85 – 392 °F ]
Circuit Application	Signal

【micropython】Improved reset to bootloader: Entering the bootloader directly from software (ST system bootloader or custom mboot) is unreliable and relies on the peripherals being enabled by the application for reliability. It is also not possi...; dcexpert MicroPython Open Source section

Embedded R&D engineer interview questions: Use your power to answer the following questions. Thank you. I. Knowledge of ANSI C/C++ I.1. Short answer questions. You must answer all the following questions correctly to get points (20 points): 1....; sdxiao Embedded System

【Contribute to C2000】 DSP BIOS lecture by Liu Xinmao: Don't say anything, just post the material directly. If you think it is useful, please reply.[[i] This post was last edited by fxw451 on 2011-4-7 09:27[/i]]...; fxw451 Microcontroller MCU

About CAN interrupt: LM3S5K31, debugging CAN process: Why can't I always enter the CAN receive interrupt? But I can enter the CAN send interrupt....; benbending Microcontroller MCU

PCB Design (Layout) Guide: [align=left][font=宋体][size=14px]1. General rules 1.1[b][url=http://www.libang.com/services/pcb_circuit.htm][b]Pre-divide the digital, analog, and DAA signal routing areas on the PCB board. 1.2 Digital...; jamieyang PCB Design

When inputting a schematic in Xilinx ISE, I want to connect an 8-bit line to 8 1-bit lines respectively. Why can't I add a bus tap?: When entering a schematic in Xilinx ISE, I want to connect an 8-bit line to eight 1-bit lines. Why can't I add a bus tap? I drag it to the required location and a few small squares appear to indicate ...; eagletie Embedded System

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components