EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

DTS20N17-35CA [V001]

Description
HERM RECP
CategoryThe connector   
File Size856KB,17 Pages
ManufacturerTE Connectivity
Websitehttp://www.te.com
Download Datasheet Parametric View All

DTS20N17-35CA [V001] Overview

HERM RECP

DTS20N17-35CA [V001] Parametric

Parameter NameAttribute value
Connector Systemline to panel, line to panel
Sealableyes
Connectors and terminals terminate toWires and cables
Housing sizeE (17)
Connector typesquare flange
Number of Positions55
Number of power supply locations0
Number of signal positions55
Pre-installedno
Shell plating materialElectroplated nickel
Shell materialStainless steel
Insulation MaterialsGlass
Sealedyes
Contact Current Rating (Max) (A)5
reverse polaritystandard
Terminal layout17 – 35
Terminal typePC tail pin
polar codeA
Joint alignment typekeying
Joint fixation typeThread
Location monitoring
Cable size (AWG)22
Working group temperature range-65 – 200 °C [ -85 – 392 °F ]
Circuit ApplicationSignal
Has the UsbAudio driver been developed for Wince?
Has anyone developed a UsbAudio driver for WinCE? Any examples or information? Thanks....
truelygo Embedded System
"Typical Examples of Embedded Application Development - STM32 Series and μC/OS-II" - Reading Chapter
File open password: vi*q!0?woc9*3g#^,,?The book "Typical Examples of Embedded Application Development - STM32 Series and μC/OS-II", which is a companion book to the STM32 development board, has entere...
sun68 stm32/stm8
FPGA and USB2.0 data acquisition card
I am now designing a data acquisition card based on FPGA and USB2.0, mainly for waveform data acquisition. Where should I start? :puzzle: :puzzle: :puzzle:...
lovefreddy FPGA/CPLD
Protel packaging summary
I found a summary of protel packages on the Internet and summarized them. I hope it will be helpful to everyone....
fengxin PCB Design
The IO pin of MSP430 is set as input, but it receives the output signal of the Hall sensor, and the chip-side signal does not switch.
The IO pins P2.0, P2.2 and P2.6 of MSP430 are set as inputs, but they receive the output signal of the Hall sensor. After the program is run, the motor is rotated manually (the Hall element of the mot...
Scaler-y Microcontroller MCU
6678 UART baud rate division factor setting
divider = (Uint32)((float)(pUARTCfg->DSP_Core_Speed_Hz)/ (float)(pUARTCfg->baudRate * 6 * osmFactor)+0.5f); Why is baudRate * 6 * osmFactor multiplied by 6? The chip manual does not mention multiplica...
liangjun DSP and ARM Processors

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 106  2160  1359  420  1089  3  44  28  9  22 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号