Pin styles S, N, F & G are compatible with the ModuMate interconnect system for socketing
and surface mounting
Not intended for socket or Surfmate mounting
Note:
Product images may not highlight current product markings.
VI-ARM™
Page 1 of 11
Rev 5.0
06/2019
VI-ARMx1xx
Electrical Characteristics
Electrical characteristics apply over the full operating range of input voltage, output load (resistive) and baseplate temperature, unless otherwise specified. All
temperatures refer to the operating temperature at the center of the baseplate. Specifications apply for AC mains having up to 5% total harmonic distortion.
Input Specifications
VI-ARM - 1
Parameter
Operating input voltage
Input undervoltage
Input surge withstand
AC line frequency
Input current, RMS
Power factor
47
47
0
0
0.60
Min
90
180
Typ
Max
132
264
90
280
63
880
7.4
5.4
47
47
0
0
0.60
Min
90
180
VI-ARMB - 2
Typ
Max
132
264
90
280
63
880
11.1
7.2
Unit
V
AC
V
AC
V
AC
V
AC
Hz
Hz
Amps
Amps
Notes
Autoranging (doubler mode)
Autoranging (bridge mode)
No damage
100ms
C, E-Grade
T & H-Grade
120V
AC
240V
AC
Dependent on line source
impedence, hold-up
capacitance, and load
30
2400
Amps
µF
264V
AC
peak line,
cold start
Inrush current
Hold-up Capacitance
30
1600
Output Specifications
VI-ARM - 1
Parameter
Output power
Efficiency
120V
AC
240 V
AC
Output voltage
Min
0
0
94
96
200
96
98
375
Typ
Max
500
750
Min
0
0
94
96
200
96
98
375
VI-ARMB - 2
Typ
Max
750
1500
Unit
Watts
Watts
%
%
V
DC
90 – 264V
AC
Notes
105 – 132V
AC
(Figure 1)
210 – 264V
AC
(Figure 2)
Control Pin Specifications
Parameter
AC Bus OK (B OK)
On-state resistance (low)
On-state current (low)
Off-state voltage
On-state threshold
Off-state threshold
Module Enable (EN)
On-state resistance (low)
On-state current (low)
Off-state voltage
On-state threshold
Off-state threshold
Overvoltage shut down
AC Bus OK - module enable,
differential error*
Min
Typ
Max
15
–50
16
245
210
15
50
16
245
195
400
16
Unit
Ω
mA
V
DC
V
DC
V
DC
Ω
mA
V
DC
V
DC
V
DC
V
DC
V
DC
AC Bus OK and module enable thresholds track
Notes
To negative output - bus normal
Bus normal
Bus abnormal, 27kΩ internal pull up to 15V
DC
(Figure 12)
Output bus voltage
Output bus voltage
To negative output - converters are disabled
150kΩ internal pull up to 15V
DC
(Figure 11)
Output bus voltage
Output bus voltage
12
235
200
14
240
205
12
235
185
380
12
14
240
190
390
14
* Tracking error between BUS OK and Enable thresholds
VI-ARM™
Page 2 of 11
Rev 5.0
06/2019
VI-ARMx1xx
Electrical Characteristics (Cont.)
Electrical characteristics apply over the full operating range of input voltage, output load (resistive) and baseplate temperature, unless otherwise specified. All
temperatures refer to the operating temperature at the center of the baseplate. Specifications apply for AC mains having up to 5% total harmonic distortion.
[size=4] Let's discuss what kind of competitions undergraduates or postgraduates can participate in? The Internet of Things seems to be quite popular now. [/size]...
Cleverly use digital phase-locked loop to measure car speed Abstract : The digital phase-locked loop chip 4046 and the variable counter 4018 are used to measure the car speed. Through counting, decodi...
I want to design a four-digit common-anode LED serial dynamic display circuit. I don't know whether to use 74HC164 or 74HC595. The original design is a two-digit serial static display circuit implemen...
Hello everyone! I want to use high voltage electricity to electrocute or stun some flying insects to count them, and analyze the data according to the characteristics and time periods of different fly...
[i=s] This post was last edited by jchjk800 on 2015-2-10 23:22 [/i] [color=#000] Pre-amplifier 0-100 times adjustable--------Filter (3-20KHZ to be determined)-------Post-amplifier 0-100 times adjustab...
In early 2002, I started to write a working program for an IC card prepaid electricity meter. The meter used Philips' 8-bit 51-expanded single-chip microcomputer
87LPC764
, and wa...[Details]
AD8205 is
a single-supply high-performance differential
amplifier
launched by
Analog
Devices of the United States
. The typical single-supply voltage is 5V, and its common-mode volta...[Details]
Problems such as the depletion of natural resources, air pollution, traffic congestion, and rising fossil fuel prices have forced societies and individuals to seek alternative means of transportati...[Details]
Motors, especially those with brushes, generate a lot of noise. This noise must be dealt with if the appliance is to meet the requirements of EMC standards. The means to solve EMC are nothing more ...[Details]
1. Proposal of
reconfigurable
measurement and control system
The measurement and control system generally refers to a system based on
computers
to realize data acquisition a...[Details]
Traditional
virtual instruments
consist of a data acquisition
board
based on PCI bus and
corresponding software. However, with
the rapid development of
computer
network techno...[Details]
A stepper motor is an electromagnetic mechanical device that converts an electrical pulse signal into an angular displacement or a linear displacement. The stability and reliability of a stepper mo...[Details]
Fruit planting is an important part of China's agricultural development, and fruit tree pest control operations are becoming more and more important. At present, the overall level of pesticide applica...[Details]
LED is the abbreviation of the English word. Its main meanings are: LED = Light Emitting Diode, a solid-state semiconductor device that can convert electrical energy into visible light. It can dire...[Details]
Don’t just look at the power when choosing a power supply
We know that a power supply with a low rated power can hardly meet the power supply needs of the system, which may cause frequent free...[Details]
Currently, high-frequency and high-efficiency DCDC converters are increasingly used in automotive electronic systems.
High switching frequency can use smaller power inductors and output filter...[Details]
1 Introduction
With the development of computer technology and information technology in the world, the global information age has arrived. All countries are formulating their own development p...[Details]
When developing electronic products with processors, how to improve anti-interference ability and electromagnetic compatibility?
1. The following systems should pay special attention to anti-...[Details]
The principles to be followed are as follows:
(1) In terms of component layout, related components should be placed as close as possible. For example, clock generators, crystal oscillat...[Details]
0 Introduction
In the design and construction of communication systems,
communication power supply
is called the heart of the communication system. The power supply system will dire...[Details]
Electronics Design Contest
京公网安备 11010802033920号
EEWORLD
