EEWORLDEEWORLDEEWORLD

Part Number

Search

MAX40088EVKIT#

Description
Amplifier IC development tool MAX40088 EV KIT
CategoryEmbedded solution    Engineering tools    Analog and digital IC development tools    Amplifier IC development tools   
File Size636KB,8 Pages
ManufacturerMaxim
Websitehttps://www.maximintegrated.com/en.html
Environmental Compliance
Download Datasheet Parametric View All

MAX40088EVKIT# Overview

Amplifier IC development tool MAX40088 EV KIT

MAX40088EVKIT# Parametric

Parameter NameAttribute value
MakerMaxim
Product CategoryAmplifier IC Development Tools
productEvaluation Kits
typeOperational Amplifiers
Tools for assessmentMAX40075, MAX40088
Working power voltage2.7 V to 5.5 V
seriesMAX40075/MAX40088
Working power current100 mA
Factory packaging quantity1
MAX40088 Evaluation Kit
Evaluates: MAX40075/MAX40088/
MAX40079/MAX40087
General Description
The MAX40088 evaluation kit (EV kit) is a fully assem-
bled and tested circuit board that contains all the
components necessary to evaluate the MAX40075/
MAX40088/MAX40079/MAX40087 ICs. The MAX40088
EV kit printed circuit board (PCB) comes installed with
MAX40088AUT+ in 6-SOT23 package.
The device is a rail-to-rail output op amp offering 10MHz
Gain Bandwidth product (MAX40075/MAX40079) and
42MHz Gain Bandwidth product (MAX40088/MAX40087).
The EV kit operates from a single 2.7V to 5.5V DC power
supply or from ±1.35V to ±2.75V split supply.
Quick Start
Required Equipment
MAX40088 EV kit
2.7V to 5.5V, 100mA DC power supply
Precision voltage calibrator
Digital multimeter
Before beginning, the following equipment is needed:
Procedure
The EV kit is fully assembled and tested. Follow the steps
below to verify board operation.
Caution:
Do not turn on power supplies until all connections
are completed and turn on V
DD
, V
SS
supplies before turning
on voltage calibrator on the input pins.
1)
2)
Make sure JU1 jumper is uninstalled and JU2 jumper
is in 1-2 position before applying supply voltage.
Connect positive terminal of the +5V supply to the
VDD test point and the GND terminal of supply to
the GND test point. Make sure JU3 is in 1-2 position
and JU4 is un-installed. JU4 is opened if split supply
operation is desired.
Connect the positive terminal of the precision voltage
calibrator to the INP/TP3 test point.
Connect the DMM to monitor the voltage on the
OUTA/TP11 test point.
Turn on the 5V power supply connected to VDD
test point, turn on the precision voltage calibrator on
INP/TP3 test point and set 0.1V. Observe the output
at the OUTA/TP11 test point on the DMM. DMM
should read approximately 1V. Also, vary IN+ voltage
between 0V to 0.45V and see if DMM on OUTA test
point is showing a gained up by voltage by 10V/V to
the voltage applied on INP test point.
Once above step is confirmed, EV kit is tested for
functionality.
Features
+2.7V to +5.5V Supply Voltage Range across V
DD
and V
SS
42MHz Gain Bandwidth Product (MAX40088/MAX40087),
Gain = 5V/V Stable
10MHz Gain Bandwidth Product (MAX40075/MAX40079),
Gain = 1V/V Stable
● Ultra-Low Distortion (0.0002% with 1kΩ load)
Proven PCB Layout
Fully Assembled and Tested
Ordering Information
appears at end of data sheet.
3)
4)
5)
319-100058; Rev 1; 12/17
[National Technology N32G457 Review] Install RT-Thread Studio
1. Download RT-Thread Studio Visit the RT-Thread official website to download the RT-Thread Studio installation package.Click [RT-Thread Studio Download]You can reach the download page https://www.rt-...
lugl4313820 Domestic Chip Exchange
Home Life Management Center
I have been so busy lately. I have not even had time to experience my beloved Mario seriously, and I have not even read the posts in the forum seriously for a long time. I guess I will be so busy for ...
sjtitr DSP and ARM Processors
【Experience Summary.02】ISE FAQs and Tips - Synthesis
I found a good blog and would like to share it with you. Introduction Synthesis is the first step to convert our design into a configuration file that FPGA can understand. This article strives to expl...
wanggq FPGA/CPLD
NXP participates in CCBN
[i=s]This post was last edited by jameswangsynnex on 2015-3-3 20:03[/i] NXP Semiconductors participated in the China International Broadcasting and Television Information Network Exhibition (CCBN) hel...
Semiconductors Mobile and portable
What is the problem when this error occurs during operation?
Exception ! Vector 13 : General Protection Fault Program Counter : 0x73d0e67d Status Register : 0x00010286 What happens when this error occurs during operation?...
Titan Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 659  1144  2543  2210  2164  14  24  52  45  44 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号