HEF4052BP,652 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > semiconductor> Switch IC> Multiplex switch IC> HEF4052BP,652

HEF4052BP,652: DescriptionMultiplex switch IC DL 4CH ANLG MUX/DMUX; Categorysemiconductor Switch IC Multiplex switch IC; File Size842KB，22 Pages; ManufacturerNexperia; Websitehttps://www.nexperia.com; Environmental Compliance

Download Datasheet Parametric Compare View All

HEF4052BP,652 Overview

Multiplex switch IC DL 4CH ANLG MUX/DMUX

HEF4052BP,652 Parametric

Parameter Name	Attribute value
Maker	Nexperia
Product Category	Multiplexer switch IC
product	Multiplexers/Demultiplexers
Number of channels	8 Channel
Configuration	2 x 1:4
On-resistance—maximum	2.5 kOhms
Run time—maximum	260 ns
Idle time—maximum	205 ns
Working power voltage	15 V
Minimum operating temperature	- 40 C
Maximum operating temperature	+ 125 C
Installation style	Through Hole
Package/box	PDIP-16
Encapsulation	Tube
bandwidth	70 MHz
high	3.2 mm
length	19.5 mm
Power supply type	Single Supply
width	6.48 mm
Close Isolation—Typical	- 50 dB
Supply current—max.	0.005 mA
Pd-power dissipation	750 mW
propagation delay time	5 ns
Factory packaging quantity	1000
Supply voltage - max.	15 V
Supply voltage - min.	3 V
unit weight	1.628 g

Preview

Download Datasheet

View All

HEF4052B

Dual 4-channel analog multiplexer/demultiplexer

Rev. 10 — 25 March 2016

Product data sheet

1. General description

The HEF4052B is a dual 4-channel analog multiplexer/demultiplexer with common

channel select logic. Each multiplexer/demultiplexer has four independent inputs/outputs

(nY0 to nY3) and a common input/output (nZ). The common channel select logic includes

two select inputs (S1 and S2) and an active LOW enable input (E). Both

multiplexers/demultiplexers contain four bidirectional analog switches, each with one side

connected to an independent input/output (nY0 to nY3) and the other side connected to a

common input/output (nZ). With E LOW, one of the four switches is selected

(low-impedance ON-state) by S1 and S2. With E HIGH, all switches are in the

high-impedance OFF-state, independent of S1 and S2. If break before make is needed,

then it is necessary to use the enable input.

and V

are the supply voltage connections for the digital control inputs (S1 and S2,

and E). The V

to V

range is 3 V to 15 V. The analog inputs/outputs (nY0 to nY3, and

nZ) can swing between V

as a positive limit and V

as a negative limit. V



may

not exceed 15 V. Unused inputs must be connected to V

, V

, or another input. For

operation as a digital multiplexer/demultiplexer, V

is connected to V

(typically

ground). V

and V

are the supply voltage connections for the switches.

2. Features and benefits



Fully static operation

5 V, 10 V, and 15 V parametric ratings

Standardized symmetrical output characteristics

Specified from

40 C

to +85

C

and

40 C

to +125

C

Complies with JEDEC standard JESD 13-B

3. Applications



Analog multiplexing and demultiplexing



Digital multiplexing and demultiplexing



Signal gating

HEF4052BP,652 Related Products

	HEF4052BP,652	HEF4052BTT,118
Description	Multiplex switch IC DL 4CH ANLG MUX/DMUX	Multiplexer switch IC Dual 4channel analog multiplxr/demultplxr
Number of channels	8 Channel	4
Minimum operating temperature	- 40 C	-40 °C
Maximum operating temperature	+ 125 C	125 °C
length	19.5 mm	5 mm
width	6.48 mm	4.4 mm

Recommended Resources

Black light insecticide circuit

3V battery power supply output +-5V voltage stabilization circuit diagram

PI regulator circuit composed of F747 double operation

FOTILE FYW-T2 intelligent hot and cold water dispenser circuit diagram

Intermittent oscillator circuit diagram

Frequency shift keying (F expansion) square wave generator circuit

Logic circuit design experience[transfer]: [Specifications are very important. Friends who have worked in the company must know that the company emphasizes specifications, especially for large designs (whether software or hardware). It is almo...; 呱呱 MCU

What could be the problem when the power supply voltage drops momentarily when the power is turned on?: Use H-bridge circuit to control two back-to-back LEDs PMOS as switch, VCCS as current limit The two LEDs light up alternately with an interval of 5ms, and the light pulse is 0.2ms.Problem phenomenon: ...; jelly_bessie Analog electronics

How to set interrupt priority in PCI DMA driver!: Can the PCI DMA driver set the interrupt priority? How to set it? Please give me some ideas!...; saint Embedded System

When compiling any project with WorkBench under Vista, sh.exe fails: When I compile any project with WorkBench under Vista, it will show that sh.exe has an error, and then WorkBench stops working. What is going on?...; 鸟 Embedded System

Bipolar stepper motor acceleration and deceleration process application (good article): Bipolar stepper motor acceleration and deceleration process application (good article)...; 蓝雨夜 Analogue and Mixed Signal

Help on self-oscillating switching power supply: I want to ask you, I want to use two switch tubes to control the on and off, and finally output about +-9V, but now the circuit does not oscillate. Is it because of the transformer? Or the circuit? Pl...; 电子、 Power technology

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components