EEWORLDEEWORLDEEWORLD

Part Number

Search

DC1496C-C

Description
Power management IC development tool LTC2941-1 Eval Board
CategoryEmbedded solution    Engineering tools    Power management IC development tools   
File Size1MB,11 Pages
ManufacturerADI
Websitehttps://www.analog.com
Environmental Compliance
Download Datasheet Parametric View All

DC1496C-C Online Shopping

Suppliers Part Number Price MOQ In stock  
DC1496C-C - - View Buy Now

DC1496C-C Overview

Power management IC development tool LTC2941-1 Eval Board

DC1496C-C Parametric

Parameter NameAttribute value
MakerADI
Product CategoryPower Management IC Development Tools
productEvaluation Boards
typeBattery Management
Tools for assessmentLTC2941-1
EncapsulationBulk
seriesLTC2941
Factory packaging quantity1
DEMO MANUAL DC1496C
LTC2941/LTC2942:
Battery Gas Gauge with I
2
C
Interface and 14-Bit ADC
DESCRIPTION
Demonstration circuit 1496C-A (Figure 1) features the
LTC
®
2941.
Demonstration circuit 1496C-B features the
LTC2942.
Demonstration circuit 1496C-C features the
LTC2941-1.
Demonstration circuit 1496C-D features the
LTC2942-1.
The C, D options have parts that use an internal
sense resistor while the A, B options rely on an external
precision sense resistor. All four devices measure battery
charge state in handheld PC and portable product applica-
tions. The operating range is perfectly suited for single
cell Li-Ion batteries. A precision analog coulomb counter
integrates current through a sense resistor between the
battery’s positive terminal and the load or charger. The
LTC2942 adds battery voltage and on-chip temperature
measurement with an internal 14-bit No Latency
∆Σ™
ADC. The three measured quantities (charge, voltage and
temperature) are stored in internal registers accessible via
the onboard SMBus/I
2
C interface.
The LTC2941/LTC2941-1 has programmable high and
low thresholds for accumulated charge. The LTC2942/
LTC2942-1 has programmable high and low thresholds for
all three measured quantities. If a programmed threshold
is exceeded, the device reports an alert using either the
SMBus alert protocol or by setting a flag in the internal
status register.
The LTC2941 and LTC2942 require only a single low
value sense resistor to set the measured current range.
The LTC2941-1 and the LTC2942-1 have their own 50mΩ
internal resistor. The default value assembled on the
DC1496 is 100mΩ for a maximum current measurement
of 500mA. Both parts have a software-configurable charge
complete/alert pin. When the pin is set for charge com-
plete, a jumper connects the pushbutton which simulates
a logic high input to indicate a full battery. When the pin is
configured for alert, the same jumper is used to connect
a red LED that indicates an alert is present.
The DC1496C is a part of the QuikEval™ system for quick
evaluation with a host controller through a PC.
Design files for this circuit board are available at
http://www.linear.com/demo/DC1496C.
L,
LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks and
No Latency
∆Σ
and QuikEval are trademarks of Linear Technology Corporation. All other
trademarks are the property of their respective owners.
Figure 1. DC1496C
dc1496cfb
1
How are user groups divided and upgraded?
How user groups are divided and upgraded....
l0700830216 Suggestions & Announcements
Features of digital display instruments
Digital display instruments, referred to as digital instruments, appeared in the early 1950s. With the application of digital measurement technology, semiconductor technology and computer technology i...
yalihuang Sensor
Does wince4.2 support .net? Urgent!
Thank you all for taking the time to answer the following questions: 1. Does WinCE 4.2 support .NET? 2. Can Windows programs developed under .NET be ported to WinCE 4.2?...
yuguohua43 Embedded System
Transfer LPC1343 development board
In line with the principle of making full use of and sharing good things with everyone, we have added the LPC1343 development board.Soso sister instructed: Friends who want it should write a brief pro...
simonprince NXP MCU
What is the default value of the pin pull-up resistor (weak pull-up) in Quartus II?
It's the weak pull-up resistor. You can choose on, off or nothing. When I don't choose anything, what does it default to? Thank you, experts....
3008202060 FPGA/CPLD
Please let me see
I use the continuous counting mode of G2553 timer A and want to read the value in the timer register TAR. Is it stored in 16-bit binary form? Why is it wrong when I assign it to a global variable dire...
青稚 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2085  2567  2127  431  1172  42  52  43  9  24 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号