spread-spectrum (dithered) square-wave output of fre-
quencies from 130kHz to 66.6MHz. The DS1089L is
shipped from the factory programmed at a specific
frequency. The DS1089L is pin-for-pin compatible with
the DS1087L, however, the DS1089L dithers at equal
percentages above and below the center frequency. The
user still has access to the internal frequency divider,
selectable ±1%, ±2%, ±4%, or ±8% dithered output, dith-
ering rate, and programmable output power-down/disable
mode through an I
2
C-compatible programming interface.
All the device settings are stored in nonvolatile (NV)
EEPROM allowing it to operate in stand-alone applica-
tions. The DS1089L also has power-down and output-en-
able control pins for power-sensitive applications.
●
●
●
●
●
Features
●
Factory-Programmed Square-Wave Generator from
33.3MHz to 66.6MHz
●
Center Frequency Remains Constant Independent of
Dither Percentage
●
No External Timing Components Required
●
EMI Reduction
●
Variable Dither Frequency
●
User Programmable Down to 130kHz with Divider
(Dependent on Master Oscillator Frequency)
●
±1%, ±2%, ±4%, or ±8% Selectable Dithered Output
●
Glitchless Output-Enable Control
●
I
2
C-Compatible Serial Interface
●
Nonvolatile Settings
●
Power-Down Mode
●
Programmable Output Power-Down/Disable Mode
Applications
Printers
Copiers
Computer Peripherals
POS Terminals
Cable Modems
Ordering Information
PART
DS1089LU-yxx*
TEMP RANGE
-40°C to +85°C
PIN-PACKAGE
8 µSOP (118 mil)
*See Standard Frequency Options Table.
Pin Configuration and Typical Operating Circuits appear at
end of data sheet.
Standard Frequency Options
PART
DS1089LU-21G
DS1089LU-4CL
DS1089LU-22F
DS1089LU-23C
DS1089LU-450
DS1089LU-866
DS1089LU-yxx
Add “/T” for Tape and Reel.
Custom frequencies available, contact factory.
FREQUENCY (MHz)
14.7456
18.432
24.576
33.3
50.0
66.6
Fixed up to 66.6
SPREAD (±%)
1
2
1
1
2
4
1, 2, 4, or 8
DITHER FREQUENCY
f
MOSC
/4096
f
MOSC
/4096
f
MOSC
/2048
f
MOSC
/4096
f
MOSC
/4096
f
MOSC
/2048 or 4096 or 8192
f
MOSC
/4096
EconOscillator is a trademark of Maxim Integrated Products, Inc.
19-7501; Rev 3; 2/15
DS1089L
3.3V Center Spread-Spectrum EconOscillator™
Absolute Maximum Ratings
Voltage on VCC Relative to Ground ....................-0.5V to +6.0V
Voltage on SPRD, PDN, OE, SDA,
SCL Relative to Ground* ...................... -0.5V to (V
CC
+ 0.5V)
Operating Temperature Range ........................... -40°C to +85°C
*This voltage must not exceed 6.0V.
Programming Temperature Range .........................0°C to +70°C
Storage Temperature Range ............................ -55°C to +125°C
Soldering Temperature ................. See IPC/JEDEC J-STD-020A
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Recommended Operating Conditions
(T
A
= -40°C to +85°C.)
PARAMETER
Supply Voltage
High-Level Input Voltage
(SDA, SCL, SPRD, PDN, OE)
Low-Level Input Voltage
(SDA, SCL, SPRD, PDN, OE)
SYMBOL
V
CC
V
IH
V
IL
(Note 1)
CONDITION
MIN
2.7
0.7 x V
CC
-0.3
TYP
3.3
MAX
3.6
V
CC
+
0.3
0.3 x
V
CC
UNITS
V
V
V
DC Electrical Characteristics
(V
CC
= +2.7V to +3.6V, T
A
= -40°C to +85°C.)
PARAMETER
High-Level Output Voltage (OUT)
Low-Level Output Voltage (OUT)
Low-Level Output Voltage (SDA)
High-Level Input Current
Low-Level Input Current
Supply Current (Active)
Standby Current (Power-Down)
SYMBOL
V
OH
V
OL1
V
OL2
I
IH
I
IL
V
OL
I
OL
= 4mA
CONDITION
I
OH
= -4mA, V
CC
= min
3mA sink current
6mA sink current
V
IH
= V
CC
V
IL
= 0V
C
L
= 15pF, f
OUT
= f
MOSCmax
Power-down mode
-1
12
10
MIN
2.4
0.4
0.4
0.6
1
TYP
MAX
UNITS
V
V
V
µA
µA
mA
µA
I
CCQ
I
CC
www.maximintegrated.com
Maxim Integrated
│
2
DS1089L
3.3V Center Spread-Spectrum EconOscillator™
Master Oscillator Characteristics
(V
CC
= +2.7V to +3.6V, T
A
= -40°C to +85°C.)
PARAMETER
SYMBOL
Internal Master Oscillator
Frequency
Master Oscillator Frequency
Tolerance
Voltage Frequency
Variation
Temperature Frequency Variation
(Note 4)
Dither Frequency Range
(Note 5)
f
MOSC
∆
f
MOSC
f
MOSC
∆
f
f
MOSC
∆
f
f
MOSC
CONDITION
MIN
33.3
TYP
MAX
66.6
+0. 5
+0.75
+0.75
+0.75
UNITS
MHz
%
%
%
V
CC
= 3.3V,
T
A
= +25°C (Notes 2, 10)
T
A
= +25°C (Note 3)
V
CC
= 3.3V,
f
OUT
= f
MOSCmax
J3 = J2 = GND
J3 = GND, J2 = V
CC
J3 = J2 = V
CC
J3 = V
CC
, J2 = GND
J1 = GND, J0 = V
CC
J1 = J0 = V
CC
T
A
= 0°C to +85°C
T
A
= -40°C to 0°C
-0. 5
-0.75
-0.75
-2.00
±1
±2
±4
±8
f
MOSC
/ 2048
f
MOSC
/ 4096
f
MOSC
/ 8192
%
Dither Frequency
(Note 5)
f
MOD
J1 = V
CC
, J0 = GND
Hz
AC Electrical Characteristics
(V
CC
= +2.7V to +3.6V, T
A
= -40°C to +85°C.)
PARAMETER
Frequency Stable After
PRESCALER Change
Power-Up Time
Enable of OUT After Exiting
Power-Down Mode
OUT Disabled After Entering
Power-Down Mode
Load Capacitance
Output Duty Cycle (f
OUT
)
t
POR
+
t
STAB
t
STAB
t
PDN
C
L
(Note 6)
(Note 6)
7
15
50
50
40
SYMBOL
CONDITION
MIN
TYP
MAX
1
200
512
UNITS
Period
µs
clock
cycles
µs
pF
%
www.maximintegrated.com
Maxim Integrated
│
3
DS1089L
3.3V Center Spread-Spectrum EconOscillator™
AC Electrical Characteristics—I
2
c Interface
PARAMETER
SCL Clock Frequency
Bus Free Time Between Stop and
Start Conditions
Hold Time (Repeated) Start
Condition
Low Period of SCL
High Period of SCL
Data Hold Time
Data Setup Time
Start Setup Time
SDA and SCL Rise Time
SDA and SCL Fall Time
Stop Setup Time
SDA and SCL Capacitive
Loading
EEPROM Write Time
SYMBOL
f
SCL
t
BUF
t
HD:STA
t
HIGH
t
LOW
(Note 7)
(V
CC
= +2.7V to +3.6V, T
A
= -40°C to +85°C, unless otherwise noted. Timing referenced to V
IL(MAX)
and V
IH(MIN)
.)
CONDITIONS
MIN
0
1.3
0.6
1.3
0.6
0
100
0.6
(Note 8)
(Note 8)
(Note 8)
(Note 9)
10
20 + 0.1CB
20 + 0.1CB
0.6
300
300
400
20
0.9
TYP
MAX
400
UNITS
kHz
µs
µs
µs
µs
µs
ns
µs
ns
ns
µs
pF
ms
t
HD:DAT
t
SU:DAT
t
SU:STA
t
R
t
F
t
SU:STO
C
B
t
WR
Nonvolatile Memory Characteristics
(V
CC
= +2.7V to +3.6V.)
Writes
Note
Note
Note
Note
Note
1:
2:
3:
4:
5:
PARAMETER
SYMBOL
+70°C
CONDITION
MIN
10,000
TYP
MAX
UNITS
All voltages are referenced to ground.
This is the absolute accuracy of the master oscillator frequency at the default settings with spread disabled.
This is the change that is observed in master oscillator frequency with changes in voltage at T
A
= +25°C.
This is the change that is observed in master oscillator frequency with changes in temperature at V
CC
= 3.3V.
The dither deviation of the master oscillator frequency is bidirectional and results in an output frequency centered at the
undithered frequency.
Note 6:
This indicates the time elapsed between power-up and the output becoming active. An on-chip delay is intentionally intro-
duced to allow the oscillator to stabilize. t
STAB
is equivalent to 512 master clock cycles and will depend on the programmed
master oscillator frequency.
Note 7:
Timing shown is for fast-mode (400kHz) operation. This device is also backward compatible with I
2
C standard-mode timing.
Note 8:
C
B
—total capacitance of one bus line in picofarads.
Note 9:
EEPROM write time applies to all the EEPROM memory and SRAM shadowed EEPROM memory when WC = 0.
The EEPROM write time begins after a stop condition occurs.
Note 10:
Typical frequency shift due to aging is ±0.25%. Aging stressing includes Level 1 moisture reflow conditioning (24hr) +125°C
bake, 168hr +85°C/85°RH moisture soak, and three solder reflow passes +269 +0/-5°C peak) followed by 408hr max V
CC
biased 125°C HTOL, 500 temperature cycles at -55°C to +125°C, 96hr +130°C/85%RH/3,6V HAST and 168hr +121°C/2
[i=s] This post was last edited by 骑IC看MCU on 2019-12-23 13:49[/i]This content is originally created by EEWORLD forum user Qi IC Kan MCU . If you want to reprint or use it for commercial purposes, you...
1. Introduction
With the rapid development of embedded-related technologies, the functions of embedded systems are becoming more and more powerful, and the application interfaces are becoming richer...
The author has also been studying the precise delay program for a long time, but often can't get the result! The following is the code analysis! If you have any questions, you can continue to communic...
[align=left][color=#000000] With an oscilloscope's built-in tools, such as cursors and automated measurements, it's easy to track down signal integrity issues that may affect your design. In addition,...
Smart home is the embodiment of Internet of Things under the influence of the Internet. Smart home connects various devices in the home (such as audio and video equipment, lighting system, curtain con...
The Portable Digital Data Acquisition System (PDDAS) uses LabVIEW Real-Time and PXI to control the wind tunnel test and record air pressure data from 128 different channels.
"The LabVIEW Real-...[Details]
System design is a complex process. It is not enough to just use ICs. There are many details to consider. This article uses a high-fidelity music playback system as an example to introduce how to s...[Details]
Battery life is critical for portable applications. For applications such as smoke detectors, security devices, and thermostats, factory-installed batteries need to last for more than 10 years. The...[Details]
My colleague and I spent the day chatting in the hotel bar. We had met with several customers. We were both wondering how come these engineers we were meeting knew almost nothing about analog techn...[Details]
This paper establishes a fuel cell engine test platform based on the NI integrated hardware and software environment. This platform can realize the test and control of fuel cell engines and their a...[Details]
Images in science fiction movies often break through the limits of reality, such as in the movie "Minority Report." Tom Cruise uses a multi-touch screen to browse information. Capacitive sensing te...[Details]
In the previous series, we have listed some basic knowledge of C language in Tables 1 to 3. We hope that beginners can strengthen their memory of the above tables and gradually learn to use them wh...[Details]
1. Overview
The Virtual CAN Interface (VCI) function library is an application program interface specifically provided for the use of ZLGCAN devices on PCs. The functions in the library ar...[Details]
1. Project Introduction
Shandong Dezhou Xingtai Paper Co., Ltd. is a newly built high-end paperboard production enterprise with domestic leading level established by Shandong Zhaodongfang Pape...[Details]
Xiaomi, a well-known Internet phone in mainland China, won a million-unit order contract from China Unicom on November 20 last year, which made Xiaomi famous in mainland China. In April this year...[Details]
Smart lighting control systems provide high controllability for various buildings and further enhance the level of green energy. They are the core products of energy conservation and digital techn...[Details]
With the continuous consumption of earth's energy and the scarcity of resources, the harm of greenhouse effect to human beings, and the serious pollution of the atmosphere to the earth, the intern...[Details]
In the analysis of electronic circuits, static analysis (also known as DC analysis) is the basis of circuit analysis. However, it is well known that electronic components are nonlinear, so the anal...[Details]
RS-422 and RS-485 are both serial data interface standards, which were developed and published by the Electronic Industries Association (EIA). RS-422 defines a balanced communication interface with a ...[Details]
The traditional display screen using 51 single-chip microcomputer to control LED dot matrix has relatively simple functions. If it is to achieve diversified functions, it often takes a lot of time ...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
