Current detecting resistors for power supply, motor circuits, etc
•
High reliability and performance with resistance
tolerance ±1.0％, T.C.R. ±100×10
-6
/K
•
Suitable for both reflow and flow solderings
•
Products with lead free termination meet EU RoHS
requirements. EU RoHS regulation is not intended for
Pb-glass contained in electrode, resistor element and glass.
•
AEC-Q200 Qualified
Resistance
(Inch Size Code)
Range
Type
L
.039
+.006
-.004
+0.1
(1.0
-0.05
)
.063±.008
(1.6±0.2)
Dimensions
inches
(mm)
W
c
d
.020
+.006
-.004
+0.1
(0.5
-0.05
)
.031
(0.8
+.006
-.004
+0.15
-0.1
)
t
dimensions and construction
c
L
c
1E (0402)
1J (0603)
1 - 10
0.1 - 0.43
0.47 - 10
.008±.004
(0.2±0.1)
.016±.004
(0.4±0.1)
.014±.004
(0.35±0.1)
.010±.004 .014±.002
(0.25±0.1) (0.35±0.05)
.018±.004
(0.45±0.1)
.014±.004
(0.35±0.1)
+.008
-.004
(0.4
+0.2
)
-0.1
.012
+.008
-.004
(0.3
+0.2
)
-0.1
.018±.004
(0.45±0.1)
W
Solder
Plating
t
d
Protective
Coating
Resistive Inner
Film
Electrode
Ni
Plating
0.1 - 0.43
.016
.079±.008
(2.0±0.2)
.049±.004
(1.25±0.1)
.016±.008
(0.4±0.2)
2A (0805)
0.47 - 10
.02±.004
(0.5±0.1)
0.1 - 0.43
2B (1206)
0.47 - 10
Ceramic
Substrate
.126±.008
(3.2±0.2)
.063±.008
(1.6±0.2)
.02±.012
(0.5±0.3)
+.008
-.004
(0.5
+0.2
)
-0.1
.02
0.1 - 0.39
2E (1210)
0.43 - 10
.126±.008
(3.2±0.2)
.102±.008
(2.6±0.2)
.02±.012
(0.5±0.3)
.016
+.008
-.004
(0.4
+0.2
)
-0.1
+.008
.02
-.004
(0.5
+0.2
)
-0.1
.016
+.008
-.004
(0.4
+0.2
)
-0.1
.024±.004
(0.6±0.1)
.024±.004
(0.6±0.1)
Derating Curve
SR73 2A (0.5W), SR73 2B (0.5W), SR73 2E (0.66W)
For resistors operated at an ambient temperature of 70°C
or above, a power rating shall be derated in accordance
with the derating curve.
ordering information
SR73
Type
2B
Size
NEW
1E: 0.166W
For resistors operated at a terminal part temperature of described for each size or above, a power rating shall be
derated in accordance with the derating curve.
Please refer to “Introduction of the derating curve based on the terminal part temperature” in the beginning of our
catalog before use.
RT
Termination
Material
RT: Sn
TD
Packaging
TD: 7" 4mm pitch punch paper
TP: 0402 only, 7" 2mm pitch paper
TPL: 0402 only, 2mm pitch paper
For further information on packaging,
please refer to Appendix A
R10
Nominal
Resistance
±2%, ±5%: 2 significant
figures + 1 multiplier “R”
indicates decimal on
values <10Ω
±1%: 3 significant figures
+ 1 multiplier “R” indicates
decimal on values <100Ω
J
Tolerance
F: ±1%
G: ±2%
J: ±5%
1J: 0.2W
2A: 0.33W, 0.5W
2B: 0.33W, 0.5W
2E: 0.5W, 0.66W
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
6/28/18
74
KOA Speer Electronics, Inc.
• 199 Bolivar Drive • Bradford, PA 16701 • USA • 814-362-5536 • Fax: 814-362-8883 • www.koaspeer.com
low resistance flat chip resistors
(anti sulfuration)
applications and ratings
Part
Designation
NEW
SR731ERT
(0402)
SR731JRT
(0603)
Power
Rating
Rated
Ambient
Temperature
70°C
70°C
Rated
Terminal
Part Temp.
125°C
125°C
T.C.R.
(ppm/°C)
Max.
±200
±200
0.2W
±300
±100
0.33W
SR732ART
(0805)
0.5W*
—
105°C
70°C
125°C
±200
±250
±100
±200
±250
±100
0.33W
SR732BRT
(1206)
0.5W*
—
110°C
70°C
125°C
±200
±250
±100
±200
±250
±100
0.5W
SR732ERT
(1210)
0.66W*
—
110°C
70°C
125°C
±200
±250
±100
±200
±250
Rated voltage =
√Power
rating x resistance value or max. working voltage, whichever is lower
1
Resistance Range
F (±1%)
E-24, E-96
1
1Ω - 10Ω
0.2Ω - 10Ω
0.1Ω - 0.18Ω
0.47Ω - 10Ω
0.2Ω - 0.43Ω
0.1Ω - 0.18Ω
0.47Ω - 10Ω
0.2Ω - 0.43Ω
0.1Ω - 0.18Ω
0.47Ω - 10Ω
0.2Ω - 0.43Ω
0.1Ω - 0.18Ω
0.47Ω - 10Ω
0.2Ω - 0.43Ω
0.1Ω - 0.18Ω
0.43Ω - 10Ω
0.2Ω - 0.39Ω
—
0.43Ω - 10Ω
0.2Ω - 0.39Ω
—
G (±2%)
E-24
1Ω - 10Ω
0.2Ω - 10Ω
0.1Ω - 0.18Ω
—
0.2Ω - 10Ω
0.1Ω - 0.18Ω
—
0.2Ω - 10Ω
0.1Ω - 0.18Ω
—
0.2Ω - 10Ω
0.1Ω - 0.18Ω
—
0.2Ω - 10Ω
0.1Ω - 0.18Ω
—
0.2Ω - 10Ω
—
—
0.2Ω - 10Ω
—
J (±5%)
E-24
1Ω - 10Ω
0.2Ω - 10Ω
0.1Ω - 0.18Ω
—
0.2Ω - 10Ω
0.1Ω - 0.18Ω
—
0.2Ω - 10Ω
0.1Ω - 0.18Ω
—
0.2Ω - 10Ω
0.1Ω - 0.18Ω
—
0.2Ω - 10Ω
0.1Ω - 0.18Ω
—
0.2Ω - 10Ω
0.1Ω - 0.18Ω
—
0.2Ω - 10Ω
0.1Ω - 0.18Ω
Operating
Temperature
Range
0.166W
-55°C
to
+155°C
The nominal resistance for SR731E (F:±1%), SR731J, 2A, 2B (0.1~0.43) and SR732E (0.1~0.39) is E-24 only
* Please use the derating curve based on the terminal part temperature in graph below.
If any questions should arise whether to use the “Rated Ambient Temperature” or the “Rated Terminal Part Temperature,” please give priority to the “Rated Terminal
Part Temperature.” Prior to use and for more details refer to “Introduction of the derating curves on the terminal part temperature” in the beginning of the catalog.
If my WINCE device enters Mass Storage Mode, then if the device is connected to a PC at this time, WINCE cannot recognize the contents of the Flash and SD card, and the PC (WINXP) sees the device as a...
I debugged several boards, and the other boards were all good. But one of them crashed when I left the simulator? And it didn't run when I powered it on again. Does anyone know why?...
As the title says: When the lower computer is working, it will generate a large amount of sampling data (nearly 5,000 times per second, and it may be faster if effective communication is possible). It...
． Experimental tasks As shown in Figure 4.1.1: Connect a light emitting diode L1 to the P1.0 port, so that L1 flashes on and off continuously, with a time interval of 0.2 seconds. 2. Circuit diagramF...
I am new to WINCE and don't know a lot of things. Please recommend some information (books, websites, e-books) on developing applications and USB drivers under WINCE. Please be as detailed as possible...
Today's computer peripherals are pursuing high speed and high versatility. In order to meet user needs, seven companies led by Intel launched the USB (Universal Serial Bus) bus protocol in 1994, wh...[Details]
China's new energy vehicles are in a transition period from research and development to real industrial development. In 2012, with the intensive launch of new energy vehicle policy planning, the de...[Details]
1. Introduction
Since the 1980s, with the continuous development of automotive electronic technology, there are more and more electronic control units in automobiles, such as electronic fuel i...[Details]
The solidification and modularization of intelligent video analysis algorithms are the current trends in the application of intelligent video analysis technology. It perfectly combines intelligent ...[Details]
introduction
The emergence of high-performance, low-power embedded CPUs and high-reliability network operating systems has made it possible to implement applications with large amounts of comp...[Details]
We know that microcontroller development tools generally include real-time online emulators and programmers. Among them, online emulators are very good tools, but they are also more expensive...[Details]
1 Introduction
Water resources are the basic conditions for human survival and the lifeline of economic development. The reality shows that due to the global shortage of water resources and th...[Details]
The concept of state machine
State machine is an important concept in software programming. More important than this concept is its flexible application. In a clear and efficient program, ther...[Details]
Among the many members of the single-chip microcomputer family, the MCS-51 series of single-chip microcomputers has occupied the main market of industrial measurement and control and automation eng...[Details]
From the previous section, we have learned that the timer/counter in the microcontroller can have multiple uses, so how can I make them work for the purpose I need? This requires setting the timer/...[Details]
Capacitance Measurement
Used to verify that capacitors meet the manufacturer's specifications. For quality control, a group of capacitors may be placed in an environmental chamber and the cap...[Details]
Introduction
Automakers are working to reduce vehicle weight to reduce CO2 emissions and improve fuel efficiency. Designers are therefore seeking new technologies and design techniques that can...[Details]
LED lighting: Basic circuit design can be completed in as little as one day
Semiconductor manufacturers are also getting involved in the LED lighting business. The power circuit of LED req...[Details]
Introduction
In industrial control, speed measurement is often required. Generally, a contact tachometer is used. This tachometer must be placed against the center of the shaft to measure. It...[Details]
The ARINC429 bus is one of the most commonly used communication buses between various subsystems of avionics. As the "skeleton" of modern avionics systems, once the bus system or the attached airbo...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
